nach oben

The International Journal of Advanced Manufacturing Technology

Erschienen in:

24.06.2023 | Technical Note

Research on surface integrity and its influencing factors in the high-speed cutting of typical aluminum/titanium/nickel alloys: a review

verfasst von: Dongkai Wang

Erschienen in: The International Journal of Advanced Manufacturing Technology | Ausgabe 9-10/2023

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

This article mainly discusses high-speed milling of aluminum/titanium/nickel alloys (common materials in the aerospace field, such as 7075-T6 aluminum, Ti6Al4V, Inconel 718). The workpiece’s surface integrity significantly impacts the part’s fatigue life, material properties (wear resistance, corrosion resistance, etc.), and tool life. Improving the surface integrity of the workpiece effectively has always been a challenging problem in the manufacturing field. This article comprehensively reviews the factors that influence surface integrity in machining, including tool geometry parameters, workpiece material (elements, microstructure)/shape, cutting environment, cutting vibration, and tool wear. The article also summarizes various methods for improving surface integrity, such as cutting path planning, cutting vibration suppression, and tool wear monitoring. The article analyzes the characteristics of surface integrity in machining related to workpiece material, including surface morphology (surface roughness, waviness, scallop height, surface defects), microstructure modification (such as plastic deformation, grain size, and white layer), and mechanical properties (microhardness, residual stress). Current research progress shows that the study of the influence of cutting parameters on surface integrity in machining is mainly based on experimental data, which deeply analyzes the correlation between the two. However, there is a lack of systematic modeling methods for the relationship between cutting parameters, physical parameters during cutting (mechanical load, thermal load), and surface integrity characteristics. Due to the importance of establishing a mapping relationship between cutting parameters, surface integrity, and component fatigue life, when studying the influence of cutting parameters on surface integrity characteristics, it is necessary to consider the final component’s fatigue life.

Vorheriger Artikel Structural and winding sequence optimization of coreless filament wound composite lattice structures

Nächster Artikel Research on vibration characteristics of silicon nitride 6206 full-ceramic bearing with different pre-tightening force and oil supply rate

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Bhopale NN, Pawade RS, Joshi SS (2017) Surface quality analysis in ball end milling of Inconel 718 cantilevers by response surface methodology. Proc Inst Mech Eng Part B J Eng Manuf 231(4):628–640. https://doi.org/10.1177/0954405415600140CrossRef

Wang FZ, Zhao J, Li AH, Zhao JB (2013) Cutting forces and surface roughness in high-speed end milling of Ti6Al4V. In: 12th Conference on Machining and Advanced Manufacturing Technology, Xiamen, Peoples R China. pp 76–81. https://doi.org/10.4028/www.scientific.net/KEM.589-590.76

Wang ZH, Yuan JT, Huang J (2011) Study on surface roughness in high-speed milling for ALMn1Cu. In: International Conference on Mechatronics and Applied Mechanics, Hong Kong, PEOPLES R CHINA, 2011. pp 636-640. https://doi.org/10.4028/www.scientific.net/AMM.157-158.636

Zhao ZY, Huang LX, Xiao YS, Liu B (2010) Research on NC technology for high speed milling. In: International Conference on Frontiers of Manufacturing and Design Science, Chongqing, Peoples R China, 2010. pp 280. https://doi.org/10.4028/www.scientific.net/AMM.44-47.280

van Dijk NJM, Doppenberg EJJ, Faassen RPH, van de Wouw N, Oosterling JAJ, Nijmeijer H (2010) Automatic in-process chatter avoidance in the high-speed milling process. J Dyn Syst Meas Control 132(3). https://doi.org/10.1115/1.4000821

Aspinwall A (1997) Surface integrity and fatigue life of turned gamma titanium aluminide. J Mater Process Technol. https://doi.org/10.1016/S0924-0136(97)00204-5

Choudhury IA, El-Baradie MA (1998) Machinability of nickel-base super alloys: a general review. J Mater Process Technol 77(1–3):278–284. https://doi.org/10.1016/S0924-0136(97)00429-9CrossRef

Moussaoui K, Mousseigne M, Senatore J, Chieragatti R (2015) The effect of roughness and residual stresses on fatigue life time of an alloy of titanium. Int J Adv Manuf Technol 78(1–4):557–563. https://doi.org/10.1007/s00170-014-6596-7CrossRef

Sharman ARC (2001) The effects of machined workpiece surface integrity on the fatigue life of γ-titanium aluminide. Int J Machine Tools Manuf 41(11):1681–1685. https://doi.org/10.1016/S0890-6955(01)00034-7CrossRef

10.

Thakur A, Gangopadhyay S (2016) State-of-the-art in surface integrity in machining of nickel-based super alloys. Int J Mach Tools Manuf 100:25–54. https://doi.org/10.1016/j.ijmachtools.2015.10.001CrossRef

11.

Chen S, Zhao W, Yan P, Qiu T, Gu H, Jiao L, Wang X (2022) Effect of milling surface topography and texture direction on fatigue behavior of ZK61M magnesium alloy. Int J Fatigue 156:11. https://doi.org/10.1016/j.ijfatigue.2021.106669CrossRef

12.

Dong W, Sullivan P, Stout K (1994) Comprehensive study of parameters for characterising three-dimensional surface topography: III: parameters for characterising amplitude and some functional properties. Wear 178(1–2):29–43. https://doi.org/10.1016/0043-1648(94)90127-9CrossRef

13.

Zhang W, Bai FS, Zhao SH, Zhang L, Wang B, Feng RY (2021) Analysis of the texture direction of the milled surface on the wear resistance of the workpiece. Surf Topogr Metrol Prop 9(3):035044. https://doi.org/10.1088/2051-672X/ac2565CrossRef

14.

Taylor D, Clancy OM (1991) The fatigue performance of machined surfaces. Fatigue Fract Eng Mater Struct 14(2–3):329–336. https://doi.org/10.1111/j.1460-2695.1991.tb00662.xCrossRef

15.

Schreck S, Gahr K (2005) Laser-assisted structuring of ceramic and steel surfaces for improving tribological properties. Appl Surf Sci 247:616–622. https://doi.org/10.1016/j.apsusc.2005.01.173CrossRef

16.

Sadeghi M, Kharaziha M, Salimijazi HR, Tabesh E (2019) Role of micro-dimple array geometry on the biological and tribological performance of Ti6Al4V for biomedical applications. Surf Coat Technol 362:282–292. https://doi.org/10.1016/j.surfcoat.2019.01.113CrossRef

17.

Wang C, Huang H, Zhang ZY, Zhang L, Yan JW, Ren LQ (2022) Formation, evolution and characterization of nanoporous structures on the Ti6Al4V surface induced by nanosecond pulse laser irradiation. Mater Design 223:111243. https://doi.org/10.1016/j.matdes.2022.111243CrossRef

18.

Yao Y-t (2021) Effects of pore size and porosity on cytocompatibility and osteogenic differentiation of porous titanium. J Mater Sci Mater Med 3–11. https://doi.org/10.1007/s10856-021-06548-0

19.

Sheng Z, Wei Q, Cheng L, Suo L, Shi Y (2014) Effects of scan line spacing on pore characteristics and mechanical properties of porous Ti6Al4V implants fabricated by selective laser melting. Materials Design 63:185–193. https://doi.org/10.1016/j.matdes.2014.05.021CrossRef

20.

Su Y, Komasa S, Sekino T, Nishizaki H, Okazaki J (2016) Nanostructured Ti6Al4V alloy fabricated using modified alkali-heat treatment: characterization and cell adhesion. Mater Sci Eng C Mater Biol Appl 59:617–623. https://doi.org/10.1016/j.msec.2015.10.077CrossRef

21.

Krolczyk GM, Nieslony P, Krolczyk JB, Samardzic I, Legutko S, Hloch S, Barrans S, Maruda RW (2015) Influence of argon pollution on the weld surface morphology. Measurement 70:203–213. https://doi.org/10.1016/j.measurement.2015.04.001CrossRef

22.

Li W, Guo Y, Guo C (2013) Superior surface integrity by sustainable dry hard milling and impact on fatigue. CIRP Ann Manuf Technol 62(1):567–570. https://doi.org/10.1016/j.cirp.2013.03.024CrossRef

23.

Chang HB, Li SY, Shi RP, (2016) Design and manufacturing technology of high speed milling cutter for aluminum alloy. In: 13th Global Congress on Manufacturing and Management, Zhengzhou Univ, Zhengzhou, Peoples R China. pp 630–637. https://doi.org/10.1016/j.proeng.2017.01.200

24.

Zeng Z (2010) Mechanical engineering materials manual: metallic materials. Mechanical Industry Press

25.

Leyens C, Peters M (2003) Titanium and titanium alloys, Titanium and titanium alloys - fundamentals and applications.

26.

Wang B, Liu ZQ (2018) Influences of tool structure, tool material and tool wear on machined surface integrity during turning and milling of titanium and nickel alloys: a review. Int J Adv Manuf Technol 98(5–8):1925–1975. https://doi.org/10.1007/s00170-018-2314-1CrossRef

27.

Panin PV, Lukina EA (2020) Machinability assessment of beta-solidifying TiAl-based alloy with Zr, Cr, and Gd content variability, Materials today: proceedings. https://doi.org/10.1016/j.matpr.2020.08.233

28.

Fu T, YuQX ,Pang SQ (2006) Study and application on CVD diamond tools, Advances in Machining & Manufacturing Technology Viii2006. pp 720-724. https://doi.org/10.4028/www.scientific.net/KEM.315-316.720

29.

Ayas E, Kara A (2004) Pressureless sintering of Al2O3-TiCN composites, Euro Ceramics Viii, Pts 1-32004. pp 849-852. https://doi.org/10.4028/10.4028/www.scientific.net/KEM.264-268.849

30.

Shalaby MA, El Hakim MA, Abdelhameed MM, Krzanowski JE, Veldhuis SC, Dosbaeva GK (2014) Wear mechanisms of several cutting tool materials in hard turning of high carbon-chromium tool steel. Tribol Int 70:148–154. https://doi.org/10.1016/j.triboint.2013.10.011CrossRef

31.

Poulachon G, Moisan A, Jawahir IS (2001) Tool-wear mechanisms in hard turning with polycrystalline cubic boron nitride tools. Elsevier B.V. pp 576–586.

32.

Desai KA, Rao PVM (2008) Effect of direction of parameterization on cutting forces and surface error in machining curved geometries. Int J Mach Tools Manuf 48(2):249–259. https://doi.org/10.1016/j.ijmachtools.2007.08.007CrossRef

33.

Tsao CC (2008) Cutting performance and predictive models for end milling aluminum alloy. In: International Conference on Advances in Materials and Processing Technologies, Manama, BAHRAIN, 2008. pp 646-653. https://doi.org/10.4028/www.scientific.net/AMR.83-86.646

34.

Sur G, Motorcu AR, Nohutcu S (2022) Single and multi-objective optimization for cutting force and surface roughness in peripheral milling of Ti6Al4V using fixed and variable helix angle tools. J Manuf Process 80:529–545. https://doi.org/10.1016/j.jmapro.2022.06.016CrossRef

35.

Petru J (2022) Statistical analysis of machining parameters on burr formation, surface roughness and energy consumption during milling of aluminium alloy Al 6061–T6. Materials 15:8065. https://doi.org/10.3390/ma15228065CrossRef

36.

Yang SC, He CS, Zheng ML (2019) A prediction model for titanium alloy surface roughness when milling with micro-textured ball-end cutters at different workpiece inclination angles. Int J Adv Manuf Technol 100(5–8):2115–2122. https://doi.org/10.1007/s00170-018-2852-6CrossRef

37.

Tong X, Yu S (2020) Influence of micro-textured parameters on cutting performance and chip formation of milling Ti6Al4V. J Mech Sci Technol 34(9):3767–3774. https://doi.org/10.1007/s12206-020-0828-9CrossRef

38.

Zhang KD, Deng JX, Meng R, Gao P, Yue HZ (2015) Effect of nano-scale textures on cutting performance of WC/Co-based Ti55Al45N coated tools in dry cutting. Int J Refract Met Hard Mater 51:35–49. https://doi.org/10.1016/j.ijrmhm.2015.02.011CrossRef

39.

Aslantas K, Alatrushi LKH, Bedir F, Kaynak Y, Yilmaz N (2020) An experimental analysis of minimum chip thickness in micro-milling of two different titanium alloys. Proc Inst Mech Eng Part B J Eng Manuf 234(12):1486–1498. https://doi.org/10.1177/0954405420933098CrossRef

40.

Campos FD, Araujo AC, Munhoz ALJ, Kapoor SG (2020) The influence of additive manufacturing on the micromilling machinability of Ti6Al4V: a comparison of SLM and commercial workpieces. J Manuf Process 60:299–307. https://doi.org/10.1016/j.jmapro.2020.10.006CrossRef

41.

Ni CB, Zhu LD, Zheng ZP, Zhang JY, Yang Y, Hong RC, Bai YC, Lu WF, Wang H (2020) Effects of machining surface and laser beam scanning strategy on machinability of selective laser melted Ti6Al4V alloy in milling. Mater Design 194:108880. https://doi.org/10.1016/j.matdes.2020.108880CrossRef

42.

Li C, Duan CZ, Chang BB (2022) Instantaneous cutting force model considering the material structural characteristics and dynamic variations in the entry and exit angles during end milling of the aluminum honeycomb core. Mech Syst Signal Process 181:109456. https://doi.org/10.1016/j.ymssp.2022.109456CrossRef

43.

Zarrouk T, Salhi JE, Nouari M, Salhi M, Chaabelasri E, Makich H, Salhi N (2022) Modeling machining of aluminum honeycomb structure. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-022-10350-9

44.

Ma JW, Hu GQ, Jia ZY, Zhang N, Wang FJ (2018) Effect of geometric feature and cutting direction on variation of force and vibration in high-speed milling of TC4 curved surface. Int J Adv Manuf Technol 95:2207–2218. https://doi.org/10.1007/s00170-017-1388-5CrossRef

45.

Daymi A, Boujelbene M, Ben Amara A, Bayraktar E, Katundi D (2011) Surface integrity in high speed end milling of titanium alloy Ti-6Al-4V. Mater Sci Technol 27(1):387–394. https://doi.org/10.1179/026708310x12738371692932CrossRef

46.

Hu D, Guo J (2018) Tool path optimization algorithm of spatial cam flank milling based on NURBS surface. J Braz Soc Mech Sci Eng 40(4):1–8. https://doi.org/10.1007/s40430-018-1092-xCrossRef

47.

Jacso A, Matyasi G, Szalay T (2019) The fast constant engagement offsetting method for generating milling tool paths. Int J Adv Manuf Technol 103(9):4293–4305. https://doi.org/10.1007/s00170-019-03834-8CrossRef

48.

Xu J, Geng Z, Sun Y, Li L (2019) Generating gouge-free tool paths for ball-end cutter CNC milling of cloud of point by projecting guide curves. Int J Adv Manuf Technol 102(5):1193–1204. https://doi.org/10.1007/s00170-018-2973-yCrossRef

49.

Ezair B, Elber G (2018) Automatic generation of globally assured collision free orientations for 5-axis ball-end tool-paths. Comput Aided Des 102:171–181. https://doi.org/10.1016/j.cad.2018.04.011CrossRef

50.

Wu P, Suzuki H, Kase K (2005) Three-axis NC cutter path generation for subdivision surface with Z-map. Jsme Int J Series C Mech Syst Mach Elements Manuf 48(4):757–762. https://doi.org/10.1299/jsmec.48.757CrossRef

51.

Ming L, Ce H, Hafeez HM (2019) Four-axis trochoidal toolpath planning for rough milling of aero-engine blisks. Chinese J Aeronautics 32(8):2009–2016. https://doi.org/10.1016/j.cja.2018.09.001CrossRef

52.

Yuan C, Mi Z, Jia X, Lin F, Shen L (2020) Tool orientation optimization and path planning for 5-axis machining. J Syst Sci Complex 34(1):83–106. https://doi.org/10.1007/s11424-020-9270-1CrossRef

53.

Wang Q, Feng Y, Gao Y, Li Z, Tan J (2018) Smooth fillet-end cutter tool path generation method on triangular-mesh surface based on modified butterfly subdivision. Int J Adv Manuf Technol 98(9):2831–2847. https://doi.org/10.1007/s00170-018-2463-2CrossRef

54.

Bo PB, Fan HY, Barton M (2022) Efficient 5-axis CNC trochoidal flank milling of 3D cavities using custom-shaped cutting tools. Comput Aided Des 151:103334. https://doi.org/10.1016/j.cad.2022.103334MathSciNetCrossRef

55.

Chuang CM, Yau HT (2005) A new approach to z-level contour machining of triangulated surface models using fillet endmills. Comput Aided Des 37(10):1039–1051. https://doi.org/10.1016/j.cad.2004.10.005CrossRef

56.

Daniyan I, Mpofu K, Fameso F, Tlhabadira I, Phokobye S (2022) Computer-aided modelling and experimental evaluation of the pocket milling operation for alloy tool steel (AISI D3). Int J Adv Manuf Technol 122(11–12):4453–4466. https://doi.org/10.1007/s00170-022-09979-3CrossRef

57.

Sap E, Usca UA, Uzun M (2022) Machining and optimization of reinforced copper composites using different cooling-lubrication conditions. J Braz Soc Mech Sci Eng 44(9):399. https://doi.org/10.1007/s40430-022-03678-6CrossRef

58.

An QL, Cai CY, Zou F, Liang X, Chen M (2020) Tool wear and machined surface characteristics in side milling Ti6Al4V under dry and supercritical CO2 with MQL conditions. Tribol Int 151:106511. https://doi.org/10.1016/j.triboint.2020.106511CrossRef

59.

Karabulut S, Bilgin M, Karakoc H, Khanna N, Sarikaya M (2022) A study on the influence of thermally assisted novel hybrid methods on the drilling behavior of Ti6Al4V alloy. Tribol Int 175:107852. https://doi.org/10.1016/j.triboint.2022.107852CrossRef

60.

Karmiris-Obratanski P, Karkalos NE, Kudelski R, Markopoulos AP (2022) Experimental study on the effect of the cooling method on surface topography and workpiece integrity during trochoidal end milling of Incoloy 800. Tribol Int 176:107899. https://doi.org/10.1016/j.triboint.2022.107899CrossRef

61.

Li GX, Yi S, Li N, Pan WC, Wen CE, Ding SL (2019) Quantitative analysis of cooling and lubricating effects of graphene oxide nanofluids in machining titanium alloy Ti6Al4V. J Mater Process Technol 271:584–598. https://doi.org/10.1016/j.jmatprotec.2019.04.035CrossRef

62.

Gupta MK, Mia M, Pruncu CI, Khan AM, Rahman MA, Jamil M, Sharma VS (2020) Modeling and performance evaluation of Al2O3, MoS2 and graphite nanoparticle-assisted MQL in turning titanium alloy: an intelligent approach. J Braz Soc Mech Sci Eng 42(4):1–21. https://doi.org/10.1007/s40430-020-2256-zCrossRef

63.

Nguyen QM, Do TV (2022) Optimal approaches for hard milling of SKD11 steel under MQL conditions using SIO2 nanoparticles. Adv Mater Sci Eng. 2022. https://doi.org/10.1155/2022/2627522

64.

Ni CB, Zhu LD, Yang ZC (2019) Comparative investigation of tool wear mechanism and corresponding machined surface characterization in feed-direction ultrasonic vibration assisted milling of Ti-6Al-4V from dynamic view. Wear 436:203006. https://doi.org/10.1016/j.wear.2019.203006CrossRef

65.

Saha S, Deb S, Bandyopadhyay PP (2022) Shadow zone in MQL application and its influence on lubricant deficiency and machinability during micro-milling. Int J Mech Sci 220:107181. https://doi.org/10.1016/j.ijmecsci.2022.107181CrossRef

66.

Yu WW, Chen J, Li YG, Zuo ZY, Chen D, An QL, Chen M, Wang HW (2021) Comprehensive study on the cutting specific energy and surface roughness of milled in situ TiB2/Al composites and Al alloys. Int J Adv Manuf Technol 112(9–10):2717–2729. https://doi.org/10.1007/s00170-020-06478-1CrossRef

67.

Rong B, Wang DS, Yang YF, Xu HJ, He N (2013) Study on the cutting forces and surface integrity in high speed milling of aluminum-lithium alloy. In: 15th International Manufacturing Conference in China, Nanjing, Peoples R China. pp 64. https://doi.org/10.4028/www.scientific.net/MSF.770.64

68.

Huang PL, Li JF, Sun J, Ge MJ (2012) Milling force vibration analysis in high-speed-milling titanium alloy using variable pitch angle mill. Int J Adv Manuf Technol 58(1–4):153–160. https://doi.org/10.1007/s00170-011-3380-9CrossRef

69.

Li Q, Gong YD, Cai M, Liu MJ (2017) Research on surface integrity in milling Inconel718 superalloy. Int J Adv Manuf Technol 92(1–4):1449–1463. https://doi.org/10.1007/s00170-017-0080-0CrossRef

70.

Quintana G, Ciurana J (2011) Chatter in machining processes: a review. Int J Mach Tools Manuf 51(5):363–376. https://doi.org/10.1016/j.ijmachtools.2011.01.001CrossRef

71.

Feng JL, Sun ZL, Jiang ZH, Yang L (2016) Identification of chatter in milling of Ti-6Al-4V titanium alloy thin-walled workpieces based on cutting force signals and surface topography. Int J Adv Manuf Technol 82(9–12):1909–1920. https://doi.org/10.1007/s00170-015-7509-0CrossRef

72.

Jiang ZX, Sun J, Xiong QC, Wang LM, Li JF (2017) Structural design of groove and micro-blade of the end mill in aluminum alloys machining based on bionics. Int J Adv Manuf Technol 88(9–12):3343–3356. https://doi.org/10.1007/s00170-016-9022-5CrossRef

73.

Nguyen HT, Wang H, Hu SJ (2014) Modeling cutter tilt and cutter-spindle stiffness for machine condition monitoring in face milling using high-definition surface metrology. Int J Adv Manuf Technol 70(5–8):1323–1335. https://doi.org/10.1007/s00170-013-5347-5CrossRef

74.

Schmitz TL, Couey J, Marsh E, Mauntler N, Hughes D (2007) Runout effects in milling: surface finish, surface location error, and stability. Int J Mach Tools Manuf 47(5):841–851. https://doi.org/10.1016/j.ijmachtools.2006.06.014CrossRef

75.

Guo ML, Wei ZC, Wang MJ, Li SQ, Wang J, Liu SX (2021) Modal parameter identification of general cutter based on milling stability theory. J Intell Manuf 32(1):221–235. https://doi.org/10.1007/s10845-020-01569-yCrossRef

76.

Mohammadi Y, Ahmadi K (2018) Frequency domain analysis of regenerative chatter in machine tools with linear time periodic dynamics. Mech Syst Signal Process 120:378–391. https://doi.org/10.1016/j.ymssp.2018.10.029CrossRef

77.

Jin HY, Sun HY, Fu HY, Han ZY (2022) Milling process stability detection for curved workpiece based on MVMD and LSTM. Int J Adv Manuf Technol 123(3–4):1025–1036. https://doi.org/10.1007/s00170-022-10030-8CrossRef

78.

Fu Y, Zhang Y, Zhou H, Li D, Liu H, Qiao H, Wang X (2016) Timely online chatter detection in end milling process. In: Mechanical Systems and Signal Processing. https://doi.org/10.1016/j.ymssp.2016.01.003

79.

Dun Y, Zhus L, Yan B, Wang S (2021) A chatter detection method in milling of thin-walled TC4 alloy workpiece based on auto-encoding and hybrid clustering. Mech Syst Signal Process. 158. https://doi.org/10.1016/j.ymssp.2021.107755

80.

Chen D, Zhang X, Zhao H Ding H Development of a novel online chatter monitoring system for flexible milling process. Mech Syst Signal Process. 159. https://doi.org/10.1016/j.ymssp.2021.107799

81.

Yang Y, Yuan JW, Tie D, Wan M, Zhang WH (2023) An efficient and accurate chatter prediction method of milling processes with a transition matrix reduction scheme. Mech Syst Signal Process. 182. https://doi.org/10.1016/j.ymssp.2022.109535

82.

Ji YJ, Wang LY, Song Y, Wang HJ, Liu ZB (2022) Investigation of robotic milling chatter stability prediction under different cutter orientations by an updated full-discretization method. J Sound Vib. 536. https://doi.org/10.1016/j.jsv.2022.117150

83.

Ji Y, Wang X, Liu Z, Wang H, Wang K, Wang D (2019) Stability prediction of five-axis ball-end finishing milling by considering multiple interaction effects between the tool and workpiece. Mech Syst Signal Process 131:261–287. https://doi.org/10.1016/j.ymssp.2019.05.058CrossRef

84.

Falta J, Sulitka M, Zeman P An analytical formulation of ZOA-based machining stability for complex tool geometries: application to 5-axis ball-end milling. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-022-10170-x

85.

Ma JJ, Li YF, Zhang DH, Zhao B, Yan XH, Pang XY (2022) Investigation of tool flank wear effect on system stability prediction in the milling of Ti-6AI-4 V thin-walled workpiece. Int J Adv Manuf Technol 122(9–10):3937–3956. https://doi.org/10.1007/s00170-022-10136-zCrossRef

86.

Yang Y, Zhang WH, Ma YC, Wan M, Dang XB (2019) An efficient decomposition-condensation method for chatter prediction in milling large-scale thin-walled structures. Mech Syst Signal Process 121:58–76. https://doi.org/10.1016/j.ymssp.2018.11.013CrossRef

87.

Zhan D, Jiang S, Niu J, Sun Y (2020) Dynamics modeling and stability analysis of five-axis ball-end milling system with variable pitch tools. Int J Mech Sci 182:105774. https://doi.org/10.1016/j.ijmecsci.2020.105774CrossRef

88.

Huang PL, Li JF, Sun J, Zhou J (2013) Study on vibration reduction mechanism of variable pitch end mill and cutting performance in milling titanium alloy. Int J Adv Manuf Technol 67(5–8):1385–1391. https://doi.org/10.1007/s00170-012-4575-4CrossRef

89.

Zheng ML, Liu YX, Nie WY, Xu SC, Bi YQ Vibration response analysis of thin-walled workpiece considering material removal effects during machining with variable pitch end mill. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-022-10299-9

90.

Nie WY, Zheng ML, Xu SC, Liu YX, Yu HB (2021) Stability analysis and structure optimization of unequal-pitch end mills. Materials 14(22):7003. https://doi.org/10.3390/ma14227003CrossRef

91.

Sellmeier V, Denkena B (2011) Stable islands in the stability chart of milling processes due to unequal tooth pitch. Int J Mach Tools Manuf 51(2):152–164. https://doi.org/10.1016/j.ijmachtools.2010.09.007CrossRef

92.

Jin G, Qi HJ, Li ZJ, Han JX (2018) Dynamic modeling and stability analysis for the combined milling system with variable pitch cutter and spindle speed variation. Commun Nonlinear Sci Numerical Simul 63:38–56. https://doi.org/10.1016/j.cnsns.2018.03.004MathSciNetCrossRefMATH

93.

Liu GY, Dang JQ, Li C, Chen M (2020) Parametric study on the tool inclination angle for side milling thin-walled workpiece edges based on finite element simulation. Proc Inst Mech Eng Part B J Eng Manuf 234(3):439–452. https://doi.org/10.1177/0954405419876159CrossRef

94.

Li D, Cao H (2021) Fuzzy control of milling chatter with piezoelectric actuators embedded to the tool holder. Mech Syst Signal Process 148:16. https://doi.org/10.1016/j.ymssp.2020.107190CrossRef

95.

Ahmed GMS, Reddy PR, Seetharamaiah N (2012) Experimental investigation of magneto rheological damping effect on surface roughness of work piece during end milling process. Int J Precis Eng Manuf 13(6):835–844. https://doi.org/10.1007/s12541-012-0109-0CrossRef

96.

Wan SK, Li XH, Su WJ, Hong J, Milling chatter mitigation with projection-based robust adaptive controller and active magnetic bearing. Int J Precis Eng Manuf.https://doi.org/10.1007/s12541-022-00710-6

97.

Aggogeri F, Al-Bender F, Brunner B, Elsaid M, Mazzola M, Merlo A, Ricciardi D, Rodriguez M, Salvi E (2013) Design of piezo-based AVC system for machine tool applications. Mech Syst Signal Process 36:53–65. https://doi.org/10.1016/j.ymssp.2011.06.012CrossRef

98.

Chaari R, Haddar M, Djemal F, Chaari F, Haddar M (2019) Passive vibration absorber effect on the machining surface quality of a flexible workpiece. CR Mec 347(12):903–911. https://doi.org/10.1016/j.crme.2019.11.014CrossRef

99.

Jeelani S, Ramakrishnan K (1983) Subsurface plastic deformation in machining 6Al-2Sn-4Zr-2Mo titanium alloy. Wear 85(1):121–130. https://doi.org/10.1016/0043-1648(83)90340-XCrossRef

100.

Mativenga PT, Mubashar A (2007) White layer formation and tool wear in high speed milling of 57HRc tool steel using coated and uncoated tools. Int J Agile Syst Manag 2(2):172–185. https://doi.org/10.1504/IJASM.2007.015787CrossRef

101.

Ginting A, Nouari M (2009) Surface integrity of dry machined titanium alloys. Int J Mach Tools Manuf 49(3–4):325–332. https://doi.org/10.1016/j.ijmachtools.2008.10.011CrossRef

102.

Pretorius CJ, Soo SL, Aspinwall DK, Harden PM, M’Saoubi R, Mantle AL (2015) Tool wear behaviour and workpiece surface integrity when turning Ti-6Al-2Sn-4Zr-6Mo with polycrystalline diamond tooling. Cirp Ann Manuf Technol 64(1):109–112. https://doi.org/10.1016/j.cirp.2015.04.058CrossRef

103.

Yang HC, Chen ZT, Zhou ZT (2015) Influence of cutting speed and tool wear on the surface integrity of the titanium alloy Ti-1023 during milling. Int J Adv Manuf Techn 78(5–8):1113–1126. https://doi.org/10.1007/s00170-014-6593-xCrossRef

104.

Li BX, Zhang S, Li JF, Wang JC, Lu SL (2020) Quantitative evaluation of mechanical properties of machined surface layer using automated ball indentation technique. Mater Sci Eng Struct Mater Prop Microstruct Process 773:138717. https://doi.org/10.1016/j.msea.2019.138717CrossRef

105.

Liang XL, Liu ZQ (2017) Experimental investigations on effects of tool flank wear on surface integrity during orthogonal dry cutting of Ti-6Al-4V. Int J Adv Manuf Technol 93(5–8):1617–1626. https://doi.org/10.1007/s00170-017-0654-xCrossRef

106.

Moricz L, Viharos ZJ, Nemeth A, Szepligeti A, Buki M (2020) Off-line geometrical and microscopic & on-line vibration based cutting tool wear analysis for micro-milling of ceramics. Measurement 163:108025. https://doi.org/10.1016/j.measurement.2020.108025CrossRef

107.

Demir HG, Yesilyurt I (2022) A comparison of four machine learning techniques and continuous wavelet transform approach for detection and classification of tool breakage during milling process, Trans Can Soc Mech Eng. https://doi.org/10.1139/tcsme-2022-0052

108.

Zhang XD, Han C, Luo M, Zhang DH (2020) Tool wear monitoring for complex part milling based on deep learning. Appl Sci Basel 10(19):6916. https://doi.org/10.3390/app10196916CrossRef

109.

Zhou YQ, Sun BT, Sun WF, Lei Z (2022) Tool wear condition monitoring based on a two-layer angle kernel extreme learning machine using sound sensor for milling process. J Intell Manuf 33(1):247–258. https://doi.org/10.1007/s10845-020-01663-1CrossRef

110.

Yang YF, Guo YL, Huang ZP, Chen N, Li L, Jiang YF, He N (2019) Research on the milling tool wear and life prediction by establishing an integrated predictive model. Measurement 145:178–189. https://doi.org/10.1016/j.measurement.2019.05.009CrossRef

111.

Liu TS, Zhu KP, Wang G (2020) Micro-milling tool wear monitoring under variable cutting parameters and runout using fast cutting force coefficient identification method. Int J Adv Manuf Technol 111(11–12):3175–3188. https://doi.org/10.1007/s00170-020-06272-zCrossRef

112.

Wiciak-Pikula M, Felusiak-Czyryca A, Twardowski P (2020) Tool Wear prediction based on artificial neural network during aluminum matrix composite milling. Sensors (Basel, Switzerland) 20(20):5798. https://doi.org/10.3390/s20205798CrossRef

113.

Yang Y, Zhao XF, Zhao L (2022) Research on asymmetrical edge tool wear prediction in milling TC4 titanium alloy using deep learning. Measurement 203:111814. https://doi.org/10.1016/j.measurement.2022.111814CrossRef

114.

Bernini L, Albertelli P, Monno M (2023) Mill condition monitoring based on instantaneous identification of specific force coefficients under variable cutting conditions. Mech Syst Signal Process 185:109820. https://doi.org/10.1016/j.ymssp.2022.109820CrossRef

115.

Zhao PY, Cheng K, Jiang B, Zuo LH (2021) Development of the innovative differential tool wear modeling for high-feed milling and its experimental verification. Proc Inst Mech Eng Part B J Eng Manuf 235(1–2):85–97. https://doi.org/10.1177/0954405420949226CrossRef

116.

Dutta S, Pal SK, Sen R (2016) Progressive tool condition monitoring of end milling from machined surface images. Proc Inst Mech Eng Part B J Eng Manuf 232(2):251–266. https://doi.org/10.1177/0954405416640417CrossRef

117.

Khorasani A, Yazdi MRS (2017) Development of a dynamic surface roughness monitoring system based on artificial neural networks (ANN) in milling operation. Int J Adv Manuf Technol 93(1–4):141–151. https://doi.org/10.1007/s00170-015-7922-4CrossRef

118.

Nowakowski L, Skrzyniarz M, Blasiak S, Bartoszuk M (2020) Influence of the cutting strategy on the temperature and surface flatness of the workpiece in face milling. Materials 13(20):4542. https://doi.org/10.3390/ma13204542CrossRef

119.

Zhong ZL, Ai X, Liu ZQ (2013) Experimental study on cutting force and surface roughness for 7050-T7451 aluminum alloy of high speed milling. In: 3rd International Conference on Advanced Design and Manufacturing Engineering, Anshan, Peoples R China, 2013. pp 1026–1030. https://doi.org/10.4028/www.scientific.net/AMM.395-396.1026

120.

Pham TH, Nguyen DT, Banh TL, Tong VC (2020) Experimental study on the chip morphology, tool-chip contact length, workpiece vibration, and surface roughness during high-speed face milling of A6061 aluminum alloy. Proc Inst Mech Eng Part B J Eng Manuf 234(3):610–620. https://doi.org/10.1177/0954405419863221CrossRef

121.

Bu GB, Zhao C, Zuo DW (2008) Experimental research on aluminum alloy blade’s surface roughness of integrate rotor based on four-axis high speed milling. In: 9th Conference on Machining and Advanced Manufacturing Technology in China, Harbin, Peoples R China. pp 390. https://doi.org/10.4028/www.scientific.net/KEM.375-376.390

122.

Liu H, Wu CH, Chen RD (2010) Effects of cutting parameters on the surface roughness of Ti6Al4V titanium alloys in side milling. In: 4th Conference on Application of Diamond and Related Materials in China/1st International Symposium on Advances in Brazed Superabrasive Tools, Xiamen, PEOPLES R CHINA, 2010. pp 289–293. https://doi.org/10.4028/www.scientific.net/SSP.175.289

123.

Yang XY, Ren CZ, Chen G, Han B, Wang Y (2011) Effect of various cooling strategies on surface roughness of high speed milling Ti-6Al-4V. In: 14th International Manufacturing Conference in China, Tianjin, Peoples R China. pp 49. https://doi.org/10.4028/www.scientific.net/MSF.697-698.49

124.

Geng GS, Xu JH, (2008) Surface integrity and fatigue property of a high speed milled titanium alloy. In: International Conference on Surface Finishing Technology and Surface Engineering, Taiyuan, Peoples R China. pp 305. https://doi.org/10.4028/www.scientific.net/AMR.53-54.305

125.

Niu, Yongsong, Zhao, Peng, Xun, Guan, Chunming (2017) Influence of finish milling parameters on machined surface integrity and fatigue behavior of Ti1023 workpiece. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-016-9818-3

126.

Samsudeensadham S, Krishnaraj V (2014) An analysis on temperature & surface roughness during end milling of Ti-6Al-4V alloy. In: 16th International Mechanical Engineering Congress (IMEC), Tamil Nadu, India. pp 38–42.https://doi.org/10.4028/www.scientific.net/AMM.592-594.38

127.

Joshi SV, Vizhian SP, Sridhar BR, Jayaram K (2008) Parametric study of machining effect on residual stress and surface roughness of nickel base super alloy UDIMET 720. In: International Conference on Multifunctional Materials and Structures, Hong Kong, Peoples R China. pp 13. https://doi.org/10.4028/www.scientific.net/AMR.47-50.13

128.

Qiao Y, Ai X, Lu ZQ (2011) Influence of cutting parameters on surface characteristics for milling powder metallurgy nickel-based superalloy. In: International Conference on Chemical, Material and Metallurgical Engineering, Beihai, Peoples R China, 2011. pp 1635. https://doi.org/10.4028/www.scientific.net/AMR.399-401.1635

129.

Chen M, Wang CD, Jiang L, Niu QL (2012) Experimental study on milling parameters regression and optimization of super high strength steel 30CrMnSiNi2A. In: 5th International Conference on High Speed Machining, Shandong Univ, Jinan, Peoples R China. pp 293. https://doi.org/10.4028/www.scientific.net/MSF.723.293

130.

Cai XJ, Qin S, An QL, Chen M (2012) Experimental investigation on surface integrity of end milling nickel based alloy-Inconel 718. In: 10th Asia-Pacific Conference on Materials Processing, Shandong Univ, Jinan, Peoples R China. pp 51–57. https://doi.org/10.4028/www.scientific.net/AMR.500.51

131.

Hassanpour H, Sadeghi MH, Shajari S, Emami M (2011) Empirical modeling and analysis of surface roughness in milling process of nickel-based super alloy Nimonic 115 through response surface methodology. In:14th International Symposium on Advances in Abrasive Technology, Stuttgart, GERMANY. pp 430–435. https://doi.org/10.4028/www.scientific.net/AMR.325.430

132.

Chen Z, Huang CZ, Li BH, Jiang GY, Tang ZY, Niu JH, Liu HL (2022) Experimental study on surface integrity of Inconel 690 milled by coated carbide inserts. Int J Adv Manuf Technol 121(5–6):3025–3042. https://doi.org/10.1007/s00170-022-09456-xCrossRef

133.

Saleem MQ, Mumtaz S (2020) Face milling of Inconel 625 via wiper inserts: Evaluation of tool life and workpiece surface integrity. J Manuf Process 56:322–336. https://doi.org/10.1016/j.jmapro.2020.04.011CrossRef

134.

Umbrello D (2013) Investigation of surface integrity in dry machining of Inconel 718. Int J Adv Manuf Technol 69(9–12):2183–2190. https://doi.org/10.1007/s00170-013-5198-0CrossRef

135.

Pkg A, Vi A, Sk A Sr, B, (2020) Evaluation of surface roughness in incremental forming using image processing based methods. Measurement 164:108055. https://doi.org/10.1016/j.measurement.2020.108055CrossRef

136.

Chen W, Zou B, Li Y, Huang C (2021) A study of a rapid method for detecting the machined surface roughness. Int J Adv Manuf Technol 117:3115–27CrossRef

137.

Younis MA (1998) On line surface roughness measurements using image processing towards an adaptive control. Comput Ind Eng 35(1–2):49–52. https://doi.org/10.1016/S0360-8352(98)00017-5CrossRef

138.

Yi H, Jian L, Peng A, Lu E, Hang Z (2016) Visual method for measuring the roughness of a grinding piece based on color indices. Opt Express 24(15):17215–17233. https://doi.org/10.1364/OE.24.017215CrossRef

139.

Yi HA, Fang RJ, Wang SA, Niu YL, Jiao YM (2022) Research on the applicability of color vision-based roughness inspection method. Surf Topogr Metrol Prop 10(2):025016. https://doi.org/10.1088/2051-672X/ac6c1dCrossRef

140.

Chollet F (2017) Xception: deep learning with depthwise separable convolutions. In: 2017 IEEE Conference on Computer Vision and Pattern Recognition (CVPR). pp 1800-1807.

141.

Su JZ, Yi HA, Ling L, Shu AH, Lu EH, Jiao YM, Wang S (2023) Multi-object surface roughness grade detection based on Faster R-CNN. Meas Sci Technol 34(1):015012. https://doi.org/10.1088/1361-6501/ac900bCrossRef

142.

Li ZQ, Xiao JD, Han X, Zhang WF (2022) Z-map based cutting force prediction for elliptical ultrasonic vibration-assisted milling process. Int J Adv Manuf Technol 120(5–6):3237–3249. https://doi.org/10.1007/s00170-022-08976-wCrossRef

143.

Gao HN, Shen HD, Yu L, Wang YL, Yang Y, Yan SC, Li QB, Hu YJ (2022) Simulation study on surface topography and roughness in milling process of curved die. Integr Ferroelectr 227(1):1–12. https://doi.org/10.1080/10584587.2022.2065570CrossRef

144.

Shujuan L, Dong Y, Li Y, Li P, Yang Z, Landers RG (2019) Geometrical simulation and analysis of ball-end milling surface topography. Int J Adv Manuf Technol 102(5):1885–1900. https://doi.org/10.1007/s00170-018-03217-5CrossRef

145.

Li ZQ, Liu Q (2013) Surface topography and roughness in hole-making by helical milling. Int J Adv Manuf Technol 66(9–12):1415–1425. https://doi.org/10.1007/s00170-012-4419-2CrossRef

146.

Chen HQ, Wang QH (2019) Modelling and simulation of surface topography machined by peripheral milling considering tool radial runout and axial drift. Proc Inst Mech Eng Part B J Eng Manuf 233(12):2227–2240. https://doi.org/10.1177/0954405419838384CrossRef

147.

Hao YS, Liu Y (2017) Analysis of milling surface roughness prediction for thin-walled parts with curved surface. Int J Adv Manuf Technol 93(5–8):2289–2297. https://doi.org/10.1007/s00170-017-0615-4CrossRef

148.

Gao HN, Yue CX, Liu XL, Nan YC (2019) Simulation of surface topography considering cut-in impact and tool flank wear. Appl Sci 9(4):732. https://doi.org/10.3390/app9040732CrossRef

149.

Hao XL, Yue CX, Liu XL, Wang LH, Liang SVY, Nan YC (2020) Modeling of convex surface topography in milling process. Metals 10(9):1218. https://doi.org/10.3390/met10091218CrossRef

150.

Zhou RH, Chen QL (2021) An analytical prediction model of surface topography generated in 4-axis milling process. Int J Adv Manuf Technol 115(9–10):3289–3299. https://doi.org/10.1007/s00170-021-07410-xCrossRef

151.

Dong YH, Li SJ, Zhang Q, Li PY, Jia Z, Li Y (2021) Modeling and analysis of micro surface topography from ball-end milling in a trochoidal milling mode. Micromachines 12(10):1203. https://doi.org/10.3390/mi12101203CrossRef

152.

Sriyotha P, Sahasrabudhe A, Yamazaki K, Mori M (2006) Geometrical modelling of a ball-end finish milling process for a surface finish. Proc Inst Mech Eng Part B J Eng Manuf 220(4):467–477. https://doi.org/10.1243/09544054jem228CrossRef

153.

Rao KV, Ramesh C (2022) Modeling of tool vibration and its effect on roundness and surface roughness of hole in helical milling of Inconel 718. J Vib Control 28(1–2):159–168. https://doi.org/10.1177/1077546320974236CrossRef

154.

Quinsat Y, Lavernhe S, Lartigue C (2011) Characterization of 3D surface topography in 5-axis milling. Wear 271(3–4):590–595. https://doi.org/10.1016/j.wear.2010.05.014CrossRef

155.

Peng ZX, Jiao L, Yan P, Yuan MX, Gao SF, Yi J, Wang XB (2018) Simulation and experimental study on 3D surface topography in micro-ball-end milling. Int J Adv Manuf Technol 96(5–8):1943–1958. https://doi.org/10.1007/s00170-018-1597-6CrossRef

156.

Lotfi S, Wassila B, Gilles D (2018) Cutter workpiece engagement region and surface topography prediction in five-axis ball-end milling. Mach Sci Technol 22(2):181–202. https://doi.org/10.1080/10910344.2017.1337131CrossRef

157.

Liu C, He Y, Wang YL, Li YF, Wang SL, Wang LX, Wang Y (2019) An investigation of surface topography and workpiece temperature in whirling milling machining. Int J Mech Sci 164:105182. https://doi.org/10.1016/j.ijmecsci.2019.105182CrossRef

158.

Sun YW, Shi ZF, Guo Q, Xu JT (2022) A novel method to predict surface topography in robotic milling of directional plexiglas considering cutter dynamical displacement. J Mater Process Technol 304:117545. https://doi.org/10.1016/j.jmatprotec.2022.117545CrossRef

159.

Chen KD, Zhang H, van de Wouw N, Detournay E (2022) An alternative approach to compute chip thickness in milling. J Manuf Sci Eng 144(11):111006. https://doi.org/10.1115/1.4054804CrossRef

160.

Kong D, Zhu J, Duan C, Lu L, Chen D (2021) Surface roughness prediction using kernel locality preserving projection and Bayesian linear regression. Mech Syst Signal Process 152(2):107474. https://doi.org/10.1016/j.ymssp.2020.107474CrossRef

161.

Kong D, Zhu J, Duan C, Lu L, Chen D (2020) Bayesian linear regression for surface roughness prediction. Mech Syst Signal Process 142:106770. https://doi.org/10.1016/j.ymssp.2020.106770CrossRef

162.

Lu YA, Wang CY, Zhou L (2019) Geometric deviation evaluation for a five-axis flank milling tool path using the tool swept envelope. Int J Adv Manuf Technol 105(10):1811–21. https://doi.org/10.1007/s00170-019-04397-4CrossRef

163.

Quintana G, Garcia-Romeu ML, Ciurana J (2011) Surface roughness monitoring application based on artificial neural networks for ball-end milling operations. J Intell Manuf 22(4):607–617. https://doi.org/10.1007/s10845-009-0323-5CrossRef

164.

Quintana G, Bustillo A, Ciurana J (2012) Prediction, monitoring and control of surface roughness in high-torque milling machine operations. Int J Comput Integr Manuf 25(12):1129–1138. https://doi.org/10.1080/0951192x.2012.684717CrossRef

165.

Ying ZZ, Shu LM, Sugita N (2022) Bone milling: on monitoring cutting state and force using sound signals. Chin J Mech Eng 35(1):61. https://doi.org/10.1186/s10033-022-00744-xCrossRef

166.

Pimenov DY, Bustillo A, Mikolajczyk T (2018) Artificial intelligence for automatic prediction of required surface roughness by monitoring wear on face mill teeth. J Intell Manuf 29(5):1045–1061. https://doi.org/10.1007/s10845-017-1381-8CrossRef

167.

Li ZM, Wang GF, He GY (2018) Surface quality monitoring based on time-frequency features of acoustic emission signals in end milling Inconel-718. Int J Adv Manuf Technol 96(5–8):2725–2733. https://doi.org/10.1007/s00170-018-1773-8CrossRef

168.

Marinescu IL, Axinte DA (2011) An automated monitoring solution for avoiding an increased number of surface anomalies during milling of aerospace alloys. Int J Mach Tools Manuf 51(4):349–357. https://doi.org/10.1016/j.ijmachtools.2010.10.005CrossRef

169.

Marinescu I, Axinte D (2009) A time-frequency acoustic emission-based monitoring technique to identify workpiece surface malfunctions in milling with multiple teeth cutting simultaneously. Int J Mach Tools Manuf 49(1):53–65. https://doi.org/10.1016/j.ijmachtools.2008.08.002CrossRef

170.

Huang PB, Zhang HJ, Lin YC (2017) Development of a Grey online modeling surface roughness monitoring system in end milling operations. J Intell Manuf 30(4):1923–1936. https://doi.org/10.1007/s10845-017-1361-zCrossRef

171.

Li SY, Li SC, Liu Z, Vladimirovich PA (2022) Roughness prediction model of milling noise-vibration-surface texture multi-dimensional feature fusion for N6 nickel metal. J Manuf Process 79:166–176. https://doi.org/10.1016/j.jmapro.2022.04.055CrossRef

172.

Wan Y, Cheng K, Fu XL, Liu ZQ (2013) An experiment-based investigation on surface corrosion resistance behaviors of aluminum alloy 7050–T7451 after end milling. Proc Inst Mech Eng J Eng Tribol 227(11):1297–1305. https://doi.org/10.1177/1350650113491084CrossRef

173.

Wang B, Zhang Q, Wang MH, Zheng YH, Kong XJ (2021) Comparison of surface integrity of Ti6Al4V titanium alloy manufactured by laser deposition and traditional method after end milling. Proc Inst Mech Eng Part C J Mech Eng Sci 235(19):4097–4108. https://doi.org/10.1177/0954406220972135CrossRef

174.

Liu C, Ren CZ, Wang GF, Yang YW, Zhang L (2015) Study on surface defects in milling Inconel 718 super alloy. J Mech Sci Technol 29(4):1723–1730. https://doi.org/10.1007/s12206-015-0345-1CrossRef

175.

Dosbaeva GK, Veldhuis SC, Elfizy A, Fox-Rabinovich G, Wagg T (2010) Microscopic observations on the origin of defects during machining of direct aged (DA) Inconel 718 superalloy. J Mater Eng Perform 19(8):1193–1198. https://doi.org/10.1007/s11665-009-9587-3CrossRef

176.

Fernandez C, Cervera PC, Platero C, Sebastian JM, Aracil R (1993) On-line surface inspection for continuous cast aluminum strip. Proc SPIE Int Soc Opt Eng 1989:26–37. https://doi.org/10.1117/12.164877CrossRef

177.

Huang XQ, Luo XB (2014) A real-time algorithm for aluminum surface defect extraction on non-uniform image from CCD camera. Comm the Acm 10(3):556–561. https://doi.org/10.1109/ICMLC.2014.7009668CrossRef

178.

Liu K, Wang H, Chen H, Qu E, Ying T, Sun H (2017) Steel surface defect detection using a new Haar-Weibull-variance model in unsupervised manner. IEEE Trans Instrument Meas 66(10):2585–2596. https://doi.org/10.1109/TIM.2017.2712838CrossRef

179.

Wei R, Bi Y (2019) Research on recognition technology of aluminum profile surface defects based on deep learning. Materials 12(10):1681–1693. https://doi.org/10.3390/ma12101681CrossRef

180.

Neuhauser FM, Bachmann G, Hora P (2019) Surface defect classification and detection on extruded aluminum profiles using convolutional neural networks. Int J Mater Form 13(3):13. https://doi.org/10.1007/s12289-019-01496-1CrossRef

181.

Zhang D, Song K, Xu J, He Y, Yan Y (2019) Unified detection method of aluminium profile surface defects: Common and rare defect categories. Opt Laser Eng 126:23–35. https://doi.org/10.1016/j.optlaseng.2019.105936CrossRef

182.

Liang Y, Xu K, Zhou P (2020) Mask gradient response-based threshold segmentation for surface defect detection of milled aluminum ingot. Sensors 20(16):4519–4541. https://doi.org/10.3390/s20164519CrossRef

183.

Niu JT, Liu ZQ, Ai X, Huang WM, Wang GJ, Duan R (2019) Characteristics of machined surface integrity in face milling Al-Li alloy 2A97 with carbide inserts. Int J Adv Manuf Technol 101(1–4):839–848. https://doi.org/10.1007/s00170-018-2907-8CrossRef

184.

Altunpak Y, Akbulut H (2009) Effects of aging heat treatment on machinability of alumina short fiber reinforced LM 13 aluminum alloy. Int J Adv Manuf Technol 43(5–6):449–454. https://doi.org/10.1007/s00170-008-1724-xCrossRef

185.

Velásquez J, Tidu A, Bolle B, Chevrier P, Fundenberger JJ (2010) Subsurface and surface analysis of high speed machined Ti–6Al–4V alloy. Mater Sci Eng A 527(10–11):2572–2578. https://doi.org/10.1016/j.msea.2009.12.018CrossRef

186.

Wang Q, Liu Z, Yang D, Mohsan A (2017) Metallurgical-based prediction of stress-temperature induced rapid heating and cooling phase transformations for high speed machining Ti-6Al-4V alloy. Mater Design 119:208–218. https://doi.org/10.1016/j.matdes.2017.01.076CrossRef

187.

Yang D, Liu ZQ (2016) Quantification of microstructural features and prediction of mechanical properties of a dual-phase Ti-6Al-4V alloy. Materials 9(8):628. https://doi.org/10.3390/ma9080628CrossRef

188.

Huang PL, Zhou J, Xu L (2022) Online measurement of the elastic recovery value of machined surface in milling titanium alloy. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-022-09293-y

189.

Zhou JM, Bushlya V, Peng RL, Johansson S, Avdovic P, Stahl JE (2012) Effects of tool wear on subsurface deformation of nickel-based superalloy. In: 1st CIRP Conference on Surface Integrity (CSI), Bremen, Germany. https://doi.org/10.1016/j.proeng.2011.11.133

190.

Brown TL, Saldana C, Murthy TG, Mann JB, Guo Y, Allard LF, King AH, Compton WD, Trumble KP, Chandrasekar S (2009) A study of the interactive effects of strain, strain rate and temperature in severe plastic deformation of copper. Acta Materialia 57(18):5491–5500. https://doi.org/10.1016/j.actamat.2009.07.052CrossRef

191.

Bushlya V, Zhou JM, Lenrick F, Avdovic P (2011) Characterization of white layer generated when turning aged Inconel 718. Proc Eng 19:60–66. https://doi.org/10.1016/j.proeng.2011.11.080CrossRef

192.

Musfirah AH, Ghani JA, Haron CHC (2017) Tool wear and surface integrity of Inconel 718 in dry and cryogenic coolant at high cutting speed. Wear 376:125–133. https://doi.org/10.1016/j.wear.2017.01.031CrossRef

193.

Liao Z, Axinte D, Mieszala M, M’Saoubi R, Abelhafeez A, Michler J, Hardy M (2018) On the influence of gamma prime upon machining of advanced nickel based superalloy. Cirp Ann 1730–1734. https://doi.org/10.1016/j.cirp.2018.03.021

194.

Liao Z, Polyakov M, Diaz OG, Axinte D, Hardy M (2019) Grain refinement mechanism of nickel-based superalloy by severe plastic deformation - mechanical machining case. Acta Materialia 180:2–14. https://doi.org/10.1016/j.actamat.2019.08.059CrossRef

195.

Mohammadi Y, Amirabadi H (2021) Analytical modeling of work hardening of duplex steel alloys in milling process. https://doi.org/10.21203/rs.3.rs-293890/v1

196.

Yin QG, Liu ZQ, Wang B, Song QH, Cai YK (2020) Recent progress of machinability and surface integrity for mechanical machining Inconel 718: a review. Int J Adv Manuf Technol 109(1–2):215–245. https://doi.org/10.1007/s00170-020-05665-4CrossRef

197.

Zhu P (2021) Effects of sequential operation with heat treatment and mechanical milling on work hardening for superalloy GH4169. Metals 11:1367. https://doi.org/10.3390/met11091367CrossRef

198.

Caixu Yue XH (2020) Analytical prediction of residual stress in the machined surface during milling. Metals 10:498. https://doi.org/10.3390/met10040498CrossRef

199.

Wan Y, Li C, Liu ZD, Sun SF (2012) Influence of milling parameters on surface residual stresses of 7050-T7451 aluminum alloy. In: 5th International Conference on High Speed Machining, Shandong Univ, Jinan, Peoples R China, 2012. pp 208. https://doi.org/10.4028/www.scientific.net/MSF.723.208

200.

Changfeng Y, Daoxia W, Liang T, Junxue R, Kaining S, Zhenchao Y (2013) Effects of cutting parameters on surface residual stress and its mechanism in high-speed milling of TB6. Proc Inst Mech Eng Part B J Eng Manuf 227(4):483–493. https://doi.org/10.1177/0954405413475771CrossRef

201.

Zhou R, Yang W (2019) Analytical modeling of machining-induced residual stresses in milling of complex surface. Int J Adv Manuf Techn 105(1–4):565–577. https://doi.org/10.1007/s00170-019-04219-7CrossRef

202.

Takahei K, Miwa S, Shamoto E, Suzuki N (2023) Parameter identification for linear model of the milling process using spindle speed variation. Prec Eng J Int Soc Precis Eng Nanotechnol 79:16–33. https://doi.org/10.1016/j.precisioneng.2022.08.011CrossRef

203.

Jovani T, Blaysat B, Chanal H, Grediac M (2022) Applying the virtual fields method to measure during milling the through-thickness residual stress distribution in aluminum-alloy sheet material. Exp Mech. https://doi.org/10.1007/s11340-022-00909-8

204.

Li M, Wang J, Yang H, Shi J (2022) Research on influence of milling process parameters on residual stress of 7055 aluminum alloy. IOP Publishing Ltd. https://doi.org/10.1088/1742-6596/2268/1/012002

205.

Yao CF, Yang ZC, Huang XC, Ren JX, Zhang DH (2011) Thestudy of residual stresses in high-speed milling of titanium alloy TC11. In: International Conference on Manufacturing Science and Materials Engineering, Shanghai, Peoples R China, 2011. pp 160-165. https://doi.org/10.4028/www.scientific.net/AMR.443-444.160

206.

Hua Y, Liu ZQ (2018) Experimental investigation of principal residual stress and fatigue performance for turned nickel-based superalloy Inconel 718. Materials 11(6):879. https://doi.org/10.3390/ma11060879CrossRef

207.

Adrien Cellier, Florent Chalon, Virginie Grimal-Perrigouas, David Bonhoure, René Leroy (2014) Effects of cutting angles in Ti-6al-4v milling process on surface integrity: influence of roughness and residual stresses on fatigue limit. Mach Sci Technol 18:565–84. https://doi.org/10.1080/10910344.2014.955369CrossRef

208.

Zhang S, Gong M, Zeng X, Gao M (2021) Residual stress and tensile anisotropy of hybrid wire arc additive-milling subtractive manufacturing. J Mater Process Technol 293:117077. https://doi.org/10.1016/j.jmatprotec.2021.117077CrossRef

209.

Tong J, Zhao J, Chen P, Zhang Z, Zhao B (2019) Effect of ultrasonic longitudinal–torsional composite milling of the residual stress on the surface of titanium alloy. Proc Inst Mech Eng Part C J Mech Eng Sci 234(8):1598–1608. https://doi.org/10.1177/0954406219896595CrossRef

210.

Mb A, Rt B, Ky B (2021) Comprehensive study on effect of orthogonal turn-milling parameters on surface integrity of Inconel 718 considering production rate as constrain. Int J Lightweight Mater Manuf 4(2):145–155. https://doi.org/10.1016/j.ijlmm.2020.09.002CrossRef

Titel: Research on surface integrity and its influencing factors in the high-speed cutting of typical aluminum/titanium/nickel alloys: a review
verfasst von: Dongkai Wang
Publikationsdatum: 24.06.2023
Verlag: Springer London
Erschienen in: The International Journal of Advanced Manufacturing Technology / Ausgabe 9-10/2023
Print ISSN: 0268-3768
Elektronische ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-023-11808-0

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 9-10/2023

A looper-thickness coordinated control strategy based on ILQ theory and GA-BP neural network

Analytical modeling of workpiece temperature in laser-assisted milling considering the combined effect of multi-heat sources

Research on the sustainable measurement of machined surface roughness under the influence of cutting environment

Theoretical aspects and design of a numerical model for friction tapered hydro-pillar processing of AISI4140 steel

The influence of pH and H2O2 on surface quality and material removal rate during W-CMP

Effect of heat treatments on microstructure and mechanical properties of AlSi10Mg alloys fabricated by laser powder bed fusion

Premium Partner

Marktübersichten