nach oben

Journal of Materials Engineering and Performance

Erschienen in:

01.01.2015

Corrosion Resistance Analysis of Sintered NdFeB Magnets Using Ultrasonic-Aided EDM Method

verfasst von: L. Li, X. T. Wei, Z. Y. Li, X. Cheng

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 1/2015

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Absract

Sintered neodymium-iron-boron (NdFeB) permanent magnets are widely used in many fields because of their excellent magnetic property. However, their poor corrosion resistance has been cited as a potential problem that limits their extensive application. This paper presents an experimental investigation into the improvement of surface corrosion resistance with the ultrasonic-aided electrical discharge machining (U-EDM) method. A scanning electron microscope was used to analyze the surface morphology of recast layers formed through the EDM and U-EDM processes. The chemical structure and elements of these recast layers were characterized using x-ray diffraction and energy dispersive spectroscopy. Corrosion resistance was also studied by means of potentiodynamic polarization, electrochemical impedance spectroscopy, and immersion tests in 0.5 mol/L H₂SO₄ solution. Experimental results show that an amorphous structure was formed in the recast layer during the EDM and U-EDM processes and that this structure could improve the corrosion resistance of sintered NdFeB magnets. Moreover, the corrosion resistance of U-EDM-treated surface was better than that of the EDM-treated surface.

Vorheriger Artikel The Influence of Temperature on the Frictional Behavior of Duplex-Coated Die Steel Rubbing Against Forging Brass

Nächster Artikel Erratum to: Influence of Electropolishing and Magnetoelectropolishing on Corrosion and Biocompatibility of Titanium Implants

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

S.D. Mao, H.X. Yang, and Z.L. Song, Corrosion Behaviour of Sintered NdFeB Deposited with an Aluminium Coating, Corros. Sci., 2011, 53, p 1887–1894CrossRef

S.D. Mao, H.X. Yang, and J.L. Li, Corrosion Properties of Aluminum Coatings Deposited on Sintered NdFeB by Ion-beam-assisted Deposition, Appl. Surf. Sci., 2011, 257, p 5581–5585CrossRef

I. Rampin, F. Bisaglia, and M. Dabalà, Corrosion Properties of NdFeB Magnets Coated by a Ni/Cu/Ni Layer in Chloride and Sulfide Environments, J. Mater. Eng. Perform., 2010, 19, p 970–975CrossRef

S.M. Tamborim Takeuchi, D.S. Azambuja, and A.M. Saliba-Silva, Corrosion Protection of NdFeB Magnets by Phosphating with Tungstate Incorporation, Surf. Coat. Technol., 2006, 200, p 6826–6831CrossRef

W.J. Mo, L.T. Zhang, Q.Z. Liu, A.D. Shan, J.S. Wu, M. Komuro, and L.P. Shen, Microstructure and Corrosion Resistance of Sintered NdFeB Magnet Modified by Intergranular Additions of MgO and ZnO, J. Rare Earth., 2008, 26, p 268–273CrossRef

J.L. Xu, Z.C. Zhong, Z.X. Huang, and J.M. Luo, Corrosion Resistance of the Titania Particles Enhanced Acrylic Resin Composite Coatings on Sintered NdFeB Permanent Magnets, J. Alloys Compd., 2013, 570, p 28–33CrossRef

W.T. He, L.Q. Zhu, H.N. Chen, H.Y. Nan, W.P. Li, H.C. Liu, and Y. Wang, Electrophoretic Deposition of Grapheme Oxide as a Corrosion Inhibitor for Sintered NdFeB, Appl. Surf. Sci., 2013, 279, p 416–423CrossRef

J.Q. Yu, Y.H. Wen, and M. Yan, Effects of Dy and Nb on the Magnetic Properties and Corrosion Resistance of Sintered NdFeB, J. Magn. Magn. Mater., 2004, 283, p 353–356CrossRef

Y.R. Wu, J.J. Ni, T.Y. Ma, and M. Yan, Corrosion Resistance of NdFeB Sintered Magnets with Intergranular Addition of Cu60Zn40 Powders, Phys. B Condens. Matter, 2010, 405, p 3303–3307CrossRef

10.

F. Liu, Q. Li, L.Q. Li, S.Y. Wang, and H.X. Zhang, Effect of Corrosion Protection of Sol Enhanced Cooperating Coatings on Sintered NdFeB Permanent Magnets, Trans. Inst. Met. Finish., 2012, 90, p 203–208CrossRef

11.

F. Liu, Q. Li, X.K. Yang, Y. Dai, F. Luo, S.Y. Wang, and H.X. Zhang, Corrosion Resistance of Environment-friendly Sealing Layer for Zn-Coated Sintered NdFeB Magnet, Mater. Corros., 2011, 62, p 1141–1148CrossRef

12.

S.W. Tang, Q.X. Chi, and J. Hu, The Evolution of Growth Morphology and Corrosion Behavior of Electrodeposited Ni-P Coatings on Alumina Borate Whisker-Reinforced Pure Aluminum Composite, Surf. Interface Anal., 2012, 44, p 1373–1378CrossRef

13.

Y.H. Cheng, Y. Zou, L. Cheng, and W. Liu, Effect of the Microstructure on the Anti-Fouling Property of the Electroless Ni-P Coating, Mater. Lett., 2008, 62, p 4283–4285CrossRef

14.

15.

M.P. Jahan, M. Rahman, and Y.S. Wong, Study of the Diffusion of Carbon, Its Sources, and Effect on Finishing Micro-EDM Performance of Cemented Carbide, J. Mater. Eng. Perform., 2012, 21, p 1655–1668CrossRef

16.

D. Ulutan and T. Ozel, Machining Induced Surface Integrity in Titanium and Nickel Alloys: A Review, Int. J. Mach. Tools Manuf, 2011, 51, p 250–280CrossRef

17.

F.L. Amorim, L.J. Stedile, R.D. Torres, P.C. Soares, and C.A.H. Laurindo, Performance and Surface Integrity of Ti6Al4V After Sinking EDM with Special Graphite Electrodes, J. Mater. Eng. Perform., 2013, 32, p 1408–1488

18.

M.P. Jahan, Y.S. Wong, and M. Rahman, A Study on the Fine-Finish Die-Sinking Micro-EDM of Tungsten Carbide Using Different Electrode Materials, J. Mater. Process. Technol., 2009, 209, p 3956–3967CrossRef

19.

J. Simao, H.G. Lee, D.K. Aspinwall, R.C. Dewes, and E.M. Aspinwall, Workpiece Surface Modification Using Electrical Discharge Machining, Int. J. Mach. Tools Manuf., 2003, 43, p 121–128CrossRef

20.

Y.L. Hwang, C.L. Kuo, and S.F. Hwang, The Coating of TiC Layer on the Surface of Nickel by Electric Discharge Coating (EDC) with a Multi-layer Electrode, J. Mater. Process. Technol., 2010, 210, p 642–652CrossRef

21.

T.C. Lee, J.H. Zhang, and W.S. Lau, Machining of Engineering Ceramics by Ultrasonic Vibration Assisted EDM Method, Mater. Manuf. Process., 1998, 13, p 133–146CrossRef

22.

Z.Y. Yu, Y. Zhang, J. Li, J. Luan, F. Zhao, and D. Guo, High Aspect Ratio Micro-hole Drilling Aided with Ultrasonic Vibration and Planetary Movement of Electrode by Micro-EDM, CIRP Ann. Manuf. Technol., 2009, 58, p 213–216CrossRef

23.

L. Li, R.G. Gou, and G.M. Yuan, A New Erosion Protection Machining Method for Sintered NdFeB Permanent Magnet, J. Aust. Ceram., 2008, 44, p 31–33

24.

Y.C. Lin, B.H. Yan, and Y.S. Chang, Machining Characteristics of Titanium Alloy (Ti-6Al-4V) Using a Combination Process of EDM with USM, J. Mater. Process. Technol., 2000, 104, p 171–177CrossRef

25.

V. Srivastava and P.M. Pandey, Effect of Process Parameters on the Performances of EDM Process with Ultrasonic Assisted Cryogenically Cooled Electrode, J. Manuf. Process., 2012, 14, p 393–402CrossRef

26.

J.L. Xu, Z.X. Huang, J.M. Luo, and Z.C. Zhong, Effect of Titania Particles on the Microstructure and Properties of the Epoxy Resin Coatings on Sintered NdFeB Permanent Magnets, J. Magn. Magn. Mater., 2014, 355, p 3–36CrossRef

Titel: Corrosion Resistance Analysis of Sintered NdFeB Magnets Using Ultrasonic-Aided EDM Method
verfasst von: L. Li
X. T. Wei
Z. Y. Li
X. Cheng
Publikationsdatum: 01.01.2015
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 1/2015
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-014-1298-8

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Absract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 1/2015

A Method to Estimate Residual Stress in Austenitic Stainless Steel Using a Microindentation Test

Effect of Die Strength and Work Piece Strength on the Wear of Hot Forging Dies

Electrodeposition, Morphology, Composition, and Corrosion Performance of Zn-Mn Coatings from a Deep Eutectic Solvent

Paired Dislocations and Their Interactions with γ′ Particles in Polycrystalline Superalloy GH4037

Multiaxial Fatigue Life Prediction for Steels Based on Some Simple Approximations

Cutting Speed Dependent Microstructure and Transformation Behavior of NiTi Alloy in Dry and Cryogenic Machining

Premium Partner

Marktübersichten