nach oben

Journal of Materials Engineering and Performance

Erschienen in:

01.11.2015

Effect of Preheat Treatment on the Texture Evolution During Cold Rolling of AA 3003 Aluminum Alloy

verfasst von: W. X. Wang, M. Ma, H. L. Li, J. X. Zhang, W. C. Liu

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 11/2015

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The effect of preheat treatment on the texture evolution during rolling of AA 3003 aluminum alloy was investigated by x-ray diffraction. The texture evolution during rolling was quantified in terms of a simple relation between the texture volume fractions and true rolling strain. It was found that the alloy annealed at 538 °C had a higher value of k _i and a lower value of n _i than the alloy annealed at 593 °C for all the texture components. The difference in texture evolution between the two preheat treatments was mainly attributed to the initial texture. The alloy annealed at 538 °C had a higher formation rate of β fiber component than the alloy annealed at 593 °C because of the relatively weak cube texture and the presence of the P texture.

Vorheriger Artikel Characterization of Tensile Properties, Limiting Strains, and Deep Drawing Behavior of AA5754-H22 Sheet at Elevated Temperature

Nächster Artikel Study on the Indentation Creep Behavior of Mg-4Al-RE-0.8Ca Magnesium Alloy

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

O. Engler, J. Hirsch, and K. Lücke, Texture Development in Al 1.8 wt.% Cu Depending on the Precipitation State—I. Rolling Textures, Acta Mater., 1989, 37, p 2743–2753CrossRef

K. Lücke and O. Engler, Effects of Particles on Development of Microstructure and Texture During Rolling and Recrystallisation in Fcc Alloys, Mater. Sci. Technol., 1990, 6, p 1113–1130CrossRef

O. Engler and K. Lücke, Influence of the Precipitation State on the Cold Rolling Texture in 8090 Al-Li Material, Mater. Sci. Eng. A, 1991, 148, p 15–23CrossRef

O. Engler, M. Crumbach, and S. Li, Alloy-Dependent Rolling Texture Simulation of Aluminium Alloys with a Grain-Interaction Model, Acta Mater., 2005, 53, p 2241–2257CrossRef

W.C. Liu, Z. Li, C.-S. Man, D. Raabe, and J.G. Morris, Effect of Precipitation on Rolling Texture Evolution in Continuous Cast AA 3105 Aluminum Alloy, Mater. Sci. Eng. A, 2006, 434, p 105–113CrossRef

N. Hansen and D. Juul Jensen, Deformation and Recrystallization Textures in Commercially Pure Aluminum, Metall. Trans. A, 1986, 17A, p 253–259CrossRef

O. Engler, Influence of the Initial Grain Size on the Rolling and Recrystallization Textures in the Alloy Al-1.8% Cu, Textures Microstruct., 1995, 23, p 61–86CrossRef

H. Yuan, Q.F. Wang, J.W. Zhang, W.C. Liu, and Y.K. Gao, Effect of Grain Shape on the Texture Evolution During Cold Rolling of Al-Mg Alloys, J. Alloys Compd., 2011, 509, p 922–928CrossRef

J. Hirsch, E. Nes, and K. Lücke, Rolling and Recrystallization Textures in Directionally Solidified Aluminum, Acta Metal., 1987, 35, p 427–438CrossRef

10.

A. Oscarsson, W.B. Hutchinson, and H.E. Ekström, Influence of Initial Microstructure on Texture and Earing in Aluminum Sheet After Cold Rolling and Annealing, Mater. Sci. Technol., 1991, 7, p 554–564CrossRef

11.

W.C. Liu, T. Zhai, C.S. Man, B. Radhakrishnan, and J.G. Morris, Effect of Initial Texture on Texture Evolution in Cold Rolled AA 5182 Aluminum Alloy, Philos. Mag., 2004, 84, p 3305–3321CrossRef

12.

X.Y. Kong, W.C. Liu, J. Li, and H. Yuan, Deformation and Recrystallization Textures in Straight-Rolled and Pseudo Cross-Rolled AA 3105 Aluminum Alloy, J. Alloys Compd., 2010, 491, p 301–307CrossRef

13.

W.C. Liu and J.G. Morris, Comparison of the Texture Evolution in Cold Rolled DC and SC AA 5182 Aluminum Alloys, Mater. Sci. Eng. A, 2003, 339, p 183–193CrossRef

14.

W.C. Liu and J.G. Morris, Quantitative Analysis of Texture Evolution in Cold-Rolled, Continuous-Cast AA 5xxx-Series Aluminum Alloys, Metall. Trans. A, 2004, 35, p 265–277CrossRef

15.

H.J. Bunge, Texture Analysis in Materials Science, Butterworths, London, 1982

16.

O. Engler, P. Yang, and X.W. Kong, On the Formation of Recrystallization Textures in Binary Al-1.3%Mn Investigated by Means of Local Texture Analysis, Acta Mater., 1996, 44, p 3349–3369CrossRef

17.

O. Engler, X.W. Kong, and P. Yang, Influence of Particle Stimulated Nucleation on the Recrystallization Textures in Cold Deformed Al-Alloys, Scripta Mater., 1997, 37, p 1665–1674CrossRef

18.

O. Daaland and E. Nes, Recrystallization Texture Development in Commercial Al-Mn-Mg Alloys, Acta Mater., 1996, 44, p 1413–1435CrossRef

19.

K. Sjølstad, O. Engler, S. Tangen, K. Marthinsen, and E. Nes, Recrystallization Textures and the Evolution of the P-Orientation as a Function of Precipitation in an AA3103 Alloy, Mater. Sci. Forum, 2002, 408–412, p 1471–1476CrossRef

20.

J. Liu and J.G. Morris, Recrystallization Textures of Continuous Cast AA 3015 Alloy: Development of the P Orientation {011} 〈566〉, Metall. Trans. A, 2003, 34, p 2029–2032CrossRef

21.

W.C. Liu and J.G. Morris, Evolution of Recrystallization and Recrystallization Texture in Continuous-Cast AA 3015 Aluminum Alloy, Metall. Trans. A, 2005, 36, p 2829–2848CrossRef

22.

W.C. Liu and J.G. Morris, Effect of Hot and Cold Deformation on the P {011} <455> Recrystallization Texture in a Continuous Cast Al-Mn-Mg Aluminum Alloy, Scripta Mater., 2006, 54, p 2095–2099CrossRef

23.

Q. Zeng, X. Wen, and T. Zhai, Effect of Precipitates on the Development of P Orientation {011} 〈566〉 in a Recrystallized Continuous Cast AA 3004 Aluminum Alloy After Cold Rolling, Metall. Trans. A, 2009, 40, p 2488–2497CrossRef

24.

J. Hirsch and K. Lücke, Overview No. 76: Mechanism of Deformation and Development of Rolling Textures in Polycrystalline f.c.c. Metals—II. Simulation and Interpretation of Experiments on the Basis of Taylor-Type Theories, Acta Metall., 1988, 36, p 2883–2904CrossRef

25.

Y. Zhou, L.S. Tóth, and K.W. Neale, On the Stability of the Ideal Orientations of Rolling Textures for F.C.C. Polycrystal, Acta Metall. Mater., 1992, 40(11), p 3179–3193CrossRef

26.

H. Masui, Simulation for f.c.c. Deformation Texture by Modified Pencil Glide Theory, Acta Mater., 1999, 47, p 4283–4298CrossRef

27.

W.C. Liu, C.-S. Man, and J.G. Morris, Lattice Rotation of the Cube Orientation to the β Fiber During Cold Rolling of AA 5052 Aluminum Alloy, Scripta Mater., 2001, 45, p 807–814CrossRef

28.

W.C. Liu, X.Y. Kong, M.B. Chen, J. Li, H. Yuan, and Q.X. Yang, Texture Development in a Pseudo Cross-Rolled AA 3105 Aluminum Alloy, Mater. Sci. Eng. A, 2009, 516, p 263–269CrossRef

Titel: Effect of Preheat Treatment on the Texture Evolution During Cold Rolling of AA 3003 Aluminum Alloy
verfasst von: W. X. Wang
M. Ma
H. L. Li
J. X. Zhang
W. C. Liu
Publikationsdatum: 01.11.2015
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 11/2015
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-015-1744-2

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 11/2015

Microhardness Distribution and Microstructural Evolution in Pure Aluminum Subjected to Severe Plastic Deformation: Elliptical Cross-Sectioned Spiral Equal-Channel Extrusion (ECSEE)

Nondestructive Evaluation of Friction Stir-Welded Aluminum Alloy to Coated Steel Sheet Lap Joint

Effects of Al3(Sc,Zr) and Shear Band Formation on the Tensile Properties and Fracture Behavior of Al-Mg-Sc-Zr Alloy

Characteristics of Friction Welding Between Solid Bar of 6061 Al Alloy and Pipe of Al-Si12CuNi Al Cast Alloy

Effect of Quenching Process on the Microstructure and Hardness of High-Carbon Martensitic Stainless Steel

Effect of Ultrasonic Vibration on Compression Behavior and Microstructural Characteristics of Commercially Pure Aluminum

Premium Partner

Marktübersichten