nach oben

Journal of Materials Engineering and Performance

Erschienen in:

09.08.2022 | Technical Article

Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties

verfasst von: Xiaoyan Yu, Jiaxiang Xue, Qingkai Shen, Zehong Zheng, Ning Ou, Wei Wu

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 3/2023

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Functionally graded material (FGM) is an appropriate response to high-performance and multi-functional applications. In this research, dual-wire plasma arc welding can be used to fabricate SS 316L-Inconel 625 FGM with a composition gradient of 50 wt.% by adjusting the volume fraction of welding wire delivered to the melt pool. The phase evolution, microstructure, composition, microhardness and tensile properties of different composition regions along the building direction were analyzed. The results show that good bonding in the bi-metallic interface region and defect-free microstructure. The microstructure along the deposition direction is mainly columnar and equiaxed dendritic structure, and the grain growth direction is mainly along the deposition direction. The existence of Laves phases is proved by EDS mapping and point detection. Due to remelting, an error is existed between the actual composition distribution and the designed discrete gradient. The microhardness value decreases first, and reaching a minimum at the bi-metallic interface of the 100–50 wt.% SS 316L, and then increase gradually (157 HV-208 HV). The ultimate tensile strength, yield strength and elongation are 554.12 ± 7.44 MPa, 340.79 ± 4.13 MPa and 26.65 ± 0.27%, respectively. From the feasibility study, the dual-wire plasma arc welding provides a novel additive manufacturing process for the FGMs.

Vorheriger Artikel Defect Control of Electro-spark Deposition WC–Co Coatings via Adjusting Pulse Energy and Deposited Layer Number

Nächster Artikel Effect of Retrogression and Re-Aging on Microstructures and Mechanical Properties of an Al-Cu-Mg Alloy

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

J.P. Oliveira, A. Shamsolhodaei, J. Shen, J.G. Lopes, R.M. Gonçalves, M. de Brito Ferraz, L. Piçarra, Z. Zeng, N. Schell, N. Zhou and, H. Seop Kim, Improving the Ductility in Laser Welded Joints of CoCrFeMnNi High Entropy Alloy to 316 Sainless Steel, Mater. Des., 2022 https://doi.org/10.1016/j.matdes.2022.110717CrossRef

A.M.S. Costa, J.P. Oliveira, V.F. Pereira, C.A. Nunes, A.J. Ramirez and, A.P. Tschiptschin, Ni-Based Mar-M247 Superalloy as a Friction Stir Processing Tool, J. Mater. Process Tech., 2018, 262, p 605–614. https://doi.org/10.1016/j.jmatprotec.2018.07.034CrossRef

L. Yan, Y.T. Chen and, F. Liou, Additive Manufacturing of Functionally Graded Metallic Materials Using Laser Metal Deposition, Addit Manuf, 2020, 31, p 100901. https://doi.org/10.1016/j.addma.2019.100901CrossRef

J. Coleman, A. Plotkowski, B. Stump, N. Raghavan, A.S. Sabau, M.J.M. Krane, J. Heigel, R.E. Ricker, L. Levine and, S.S. Babu, Sensitivity of Thermal Predictions to Uncertain Surface Tension Data in Laser Additive Manufacturing, J. Heat Trans., 2020 https://doi.org/10.1115/1.4047916CrossRef

G. Xu, R. Wu, K. Luo and, J. Lu, Effects of Heat Treatment on Hot Corrosion Behavior of Directed Energy Deposited In718/316L Functionally Graded Material, Corros. Sci., 2022, 197, p 110068.CrossRef

U. Savitha, G. Jagan Reddy, A. Venkataramana, A. Sambasiva Rao, A.A. Gokhale and, M. Sundararaman, Chemical Analysis, Structure and Mechanical Properties of Discrete and Compositionally Graded SS316–IN625 Dual Materials, Mater. Sci. Eng.: A, 2015, 647, p 344–352. https://doi.org/10.1016/j.msea.2015.09.001CrossRef

R. Ghanavati and H. Naffakh-Moosavy, Additive Manufacturing of Functionally Graded Metallic Materials: A Review of Experimental and Numerical Studies, J. Mater. Res. Technol., 2021, 13, p 1628–1664. https://doi.org/10.1016/j.jmrt.2021.05.022CrossRef

A. Strojny-Nedza, K. Pietrzak and, W. Weglewski, The Influence of Al2O3 Powder Morphology on the Properties of Cu-Al2O3 Composites Designed for Functionally Graded Materials (FGM), J. Mater. Eng. Perform., 2016, 25(8), p 3173–3184. https://doi.org/10.1007/s11665-016-2204-3CrossRef

M. K, FGM Activities in Japan, Compos. Part B: Eng., 1997, 28(1–2), p 1–4. https://doi.org/10.1016/S1359-8368(96)00016-9CrossRef

10.

B.E. Carroll, R.A. Otis, J.P. Borgonia, J.O. Suh, R.P. Dillon, A.A. Shapiro, D.C. Hofmann, Z.K. Liu and, A.M. Beese, Functionally Graded Material of 304L Stainless Steel and inconel 625 Fabricated by Directed Energy Deposition: Characterization and Thermodynamic Modeling, Acta Mater., 2016, 108, p 46–54. https://doi.org/10.1016/j.actamat.2016.02.019CrossRef

11.

K. Shah, I. ulHaq, A. Khan, S.A. Shah, M. Khan and, A.J. Pinkerton, Parametric Study of Development of Inconel-Steel Functionally Graded Materials by Laser Direct Metal Deposition, Mater. Des., 2014, 54, p 531–538. https://doi.org/10.1016/j.matdes.2013.08.079CrossRef

12.

S. Mohan Kumar, A. Rajesh Kannan, N. Pravin Kumar, R. Pramod, N. Siva Shanmugam, A.S. Vishnu and, S.G. Channabasavanna, Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material, J. Mater. Eng. Perform., 2021, 30(8), p 5692–5703. https://doi.org/10.1007/s11665-021-05617-3CrossRef

13.

G.H. Loh, E.J. Pei, D. Harrison and, M.D. Monzon, An Overview of Functionally Graded Additive Manufacturing, Addit Manuf, 2018, 23, p 34–44. https://doi.org/10.1016/j.addma.2018.06.023CrossRef

14.

D. Raabe, C.C. Tasan and, E.A. Olivetti, Strategies for Improving the Sustainability of Structural Metals, Nature, 2019, 575, p 64–74.CrossRef

15.

W. Zixian, G. Shi, Y. Yang, X. Wen, C. Guo, and A. Zhang, Micro Metal Additive Manufactured Low-Loss Slotted Rectangular Waveguides Operating at 220-500 GHz, Front. Phys., 2021 https://doi.org/10.3389/fphy.2021.696318CrossRef

16.

A. Singh, S. Kapil, and M. Das, A Comprehensive Review of the Methods and Mechanisms for Powder Feedstock Handling in Directed Energy Deposition, Addit Manuf, 2020, 35, p 101388. https://doi.org/10.1016/j.addma.2020.101388CrossRef

17.

W. Meng, W.H. Zhang, W. Zhang, X.H. Yin, and B. Cui, Fabrication of Steel-Inconel Functionally Graded Materials by Laser Melting Deposition Integrating with Laser Synchronous Preheating, Opt. Laser Technol., 2020, 131, p 106451. https://doi.org/10.1016/j.optlastec.2020.106451CrossRef

18.

A.U. Rehman, N.K. Babu, M.K. Talari, Y.S. Usmani, and H. Al-Khalefah, Microstructure and Mechanical Property Correlation Between Rotary Friction Welded Nitinol–Nitinol Joints, Front. Mater., 2021 https://doi.org/10.3389/fmats.2021.726383CrossRef

19.

A. Reichardt, R.P. Dillon, J.P. Borgonia, A.A. Shapiro, B.W. McEnerney, T. Momose, and P. Hosemann, Development and Characterization of Ti-6Al-4V to 304L Stainless Steel Gradient Components Fabricated with Laser Deposition Additive Manufacturing, Mater. Des., 2016, 104, p 404–413. https://doi.org/10.1016/j.matdes.2016.05.016CrossRef

20.

C. Wei, Z. Sun, Q. Chen, Z. Liu, and L. Li, Additive Manufacturing of Horizontal and 3D Functionally Graded 316L/Cu10Sn Components via Multiple Material Selective Laser Melting, J. Manuf. Sci. Eng., 2019 https://doi.org/10.1115/1.4043983CrossRef

21.

Y. Su, B. Chen, C. Tan, X. Song, and J. Feng, Influence of Composition Gradient Variation on the Microstructure and Mechanical Properties of 316 L/Inconel718 Functionally Graded Material Fabricated by Laser Additive Manufacturing, J. Mater. Process Tech., 2020, 283, p 116702. https://doi.org/10.1016/j.jmatprotec.2020.116702CrossRef

22.

E. Tenuta, A. Nycz, M. Noakes, S. Simunovic, and M.H.A. Piro, Material Properties and Mechanical Behaviour of Functionally Graded Steel Produced by Wire-Arc Additive Manufacturing, Addit. Manuf., 2021, 46, p 102175. https://doi.org/10.1016/j.addma.2021.102175CrossRef

23.

W.C. Ke, J.P. Oliveira, B.Q. Cong, S.S. Ao, Z.W. Qi, B. Peng, and Z. Zeng, Multi-Layer Deposition Mechanism in Ultra High-Frequency Pulsed Wire Arc Additive Manufacturing (WAAM) of NiTi Shape Memory Alloys, Addit. Manuf., 2022, 50, p 102513. https://doi.org/10.1016/j.addma.2021.102513CrossRef

24.

A. Ramalho, T.G. Santos, B. Bevans, Z. Smoqi, J.P. Oliveira, and P. Rao, Effect of Contaminations on the Acoustic Emissions During Wire and Arc Additive Manufacturing of 316L Stainless Steel, Addit. Manuf., 2022, 51, p 102585. https://doi.org/10.1016/j.addma.2021.102585CrossRef

25.

Q.K. Shen, X.D. Kong, X.Z. Chen, X.K. Yao, V.B. Deev, and E.S. Prusov, Powder Plasma Arc Additive Manufactured CoCrFeNi(SiC)(x) High-Entropy Alloys: Microstructure and Mechanical Properties, Mater. Lett., 2021 https://doi.org/10.1016/j.matlet.2020.128736CrossRef

26.

S. Qingkai, and K.C.Y.D.P. XiangdongXizhangXukaiVBES, Powder Plasma Arc Additive Manufactured CoCrFeNi(SiC)x High-Entropy Alloys: Microstructure and Mechanical Properties, Mater. Lett., 2021, 282, p 128736. https://doi.org/10.1016/j.matlet.2020.128736CrossRef

27.

X. Chen, J. Han, J. Wang, Y. Cai, G. Zhang, L. Lianzhong, Y. Xin, and Y. Tian, A Functionally Graded Material from TC4 to 316L Stainless Steel Fabricated by Double-Wire + Arc Additive Manufacturing, Mater. Lett., 2021, 300, p 130141. https://doi.org/10.1016/j.matlet.2021.130141CrossRef

28.

G. Marinelli, F. Martina, H. Lewtas, D. Hancock, S. Ganguly, and S. Williams, Functionally Graded Structures of Refractory Metals by Wire Arc Additive Manufacturing, Sci. Technol. Weld. Jol., 2019, 24(5), p 495–503. https://doi.org/10.1080/13621718.2019.1586162CrossRef

29.

C. Shen, Z. Pan, D. Cuiuri, J. Roberts, and H. Li, Fabrication of Fe-FeAl Functionally Graded Material Using the Wire-Arc Additive Manufacturing Process, Metall. Mater. Trans. B, 2015, 47(1), p 763–772. https://doi.org/10.1007/s11663-015-0509-5CrossRef

30.

J. Han, L. Lianzhong, Y. Xin, X. Chen, G. Zhang, Y. Cai, and Y. Tian, Microstructure and Mechanical Properties of a Novel Functionally Graded Material from Ti6Al4V to Inconel 625 Fabricated by Dual Wire + Arc Additive Manufacturing, J. Alloy. Compd., 2022, 903, p 163981. https://doi.org/10.1016/j.jallcom.2022.163981CrossRef

31.

T.A. Rodrigues, N. Bairrão, F.W.C. Farias, A. Shamsolhodaei, J. Shen, N. Zhou, E. Maawad, N. Schell, T.G. Santos, and J.P. Oliveira, Steel-Copper Functionally Graded Material Produced by Twin-Wire and Arc Additive Manufacturing (T-WAAM), Mater. Des., 2022, 213, p 110270. https://doi.org/10.1016/j.matdes.2021.110270CrossRef

32.

C. Shen, K.-D. Liss, M. Reid, Z. Pan, X. Hua, F. Li, G. Mou, Y. Huang, B. Dong, D. Luo, and H. Li, Effect of the Post-Production Heat Treatment on Phase Evolution in the fe3Ni–FeNi Functionally Graded Material: An in-Situ Neutron Diffraction Study, Intermetallics, 2021, 129, p 107032. https://doi.org/10.1016/j.intermet.2020.107032CrossRef

33.

T.S. Senthil, S.R. Babu, M. Puviyarasan, and V. Dhinakaran, Mechanical and Microstructural Characterization of Functionally Graded INCONEL 825-SS316L Fabricated Using Wire Arc Additive Manufacturing, J. Mater. Res. Technol., 2021, 15, p 661–669. https://doi.org/10.1016/j.jmrt.2021.08.060CrossRef

34.

J.R. Zhang, X.J. Di, X. Jiang, and C.N. Li, Effect of Synchronous Electromagnetic Stirring on Laves Phase Morphology and Mechanical Property of Inconel625-HSLA Steel Functionally Graded Material Fabricated by Wire Arc Additive Manufacturing, Mater. Lett., 2022, 316, p 132015. https://doi.org/10.1016/j.matlet.2022.132015CrossRef

35.

D. Zaguliaev, S. Konovalov, Y. Ivanov, and V. Gromov, Effect of Electron-Plasma Alloying on Structure and Mechanical Properties of Al-Si Alloy, Appl. Surf. Sci., 2019, 498, p 143767. https://doi.org/10.1016/j.apsusc.2019.143767CrossRef

36.

V. Hutsaylyuk, M. Student, V. Posuvailo, O. Student, V. Hvozdets’kyi, P. Maruschak, and V. Zakiev, The role of Hydrogen in the Formation of Oxide-Ceramic Layers on Aluminum Alloys During their Plasma-Electrolytic Oxidation, J. Market. Res., 2021, 14, p 1682–1696. https://doi.org/10.1016/j.jmrt.2021.07.082CrossRef

37.

W. Yangfan, C. Xizhang, and S. Chuanchu, Microstructure and Mechanical Properties of INCONEL 625 Fabricated by Wire-Arc Additive Manufacturing, Surf. Coat. Technol., 2019, 374, p 116–123. https://doi.org/10.1016/j.surfcoat.2019.05.079CrossRef

38.

T. Pinomaa, M. Lindroos, M. Walbruhl, N. Provatas, and A. Laukkanen, The Significance of Spatial Length Scales and Solute Segregation in Strengthening Rapid Solidification Microstructures of 316L Stainless Steel, Acta Mater., 2020, 184, p 1–16. https://doi.org/10.1016/j.actamat.2019.10.044CrossRef

39.

G.T. Gray, V. Livescu, P.A. Rigg, C.P. Trujillo, C.M. Cady, S.R. Chen, J.S. Carpenter, T.J. Lienert, and S.J. Fensin, Structure/Property (Constitutive and Spallation Response) of Additively Manufactured 316L Stainless Steel, Acta Mater., 2017, 138, p 140–149. https://doi.org/10.1016/j.actamat.2017.07.045CrossRef

40.

S.H. Kim, H. Lee, S.M. Yeon, C. Aranas, K. Choi, J. Yoon, S.W. Yang, and H. Lee, SELECTIVE Compositional Range Exclusion via Directed Energy Deposition to Produce a Defect-free INCONEL 718/SS 316L Functionally Graded Material, Addit. Manuf., 2021, 47, p 102288. https://doi.org/10.1016/j.addma.2021.102288CrossRef

41.

W. Li, X. Chen, L. Yan, J. Zhang, X. Zhang, and F. Liou, Additive Manufacturing of a New Fe-Cr-Ni Alloy with Gradually Changing Compositions with Elemental Powder Mixes and Thermodynamic Calculation, Int. J. Adv. Manuf. Tech., 2017, 95(1–4), p 1013–1023. https://doi.org/10.1007/s00170-017-1302-1CrossRef

42.

D.Y. Deng, R.L. Peng, H. Brodin, and J. Moverare, Microstructure and Mechanical Properties of Inconel 718 Produced by Selective Laser Melting: Sample Orientation Dependence and Effects of Post Heat Treatments, Mat. Sci. Eng. A-Struct., 2018, 713, p 294–306. https://doi.org/10.1016/j.msea.2017.12.043CrossRef

43.

D.C. Kong, C.F. Dong, S.L. Wei, X.Q. Ni, L. Zhang, R.X. Li, L. Wang, C. Man and X.G. Li, About Metastable Cellular Structure in Additively Manufactured Austenitic Stainless Steels, Addit. Manuf., 2021, 38, p 101804. https://doi.org/10.1016/j.addma.2020.101804CrossRef

44.

D. Wu, X. Liang, Q. Li, and L. Jiang, Laser Rapid Manufacturing of Stainless Steel 316L/Inconel718 Functionally Graded Materials: Microstructure Evolution and Mechanical Properties, Int. J. Opt., 2010, 2010, p 1–5. https://doi.org/10.1155/2010/802385CrossRef

45.

Y. Zhong, Z.Z. Zheng, J.J. Li, and C. Wang, Fabrication of 316L Nuclear Nozzles on the Main Pipeline with Large Curvature by CMT Wire Arc Additive Manufacturing and Self-Developed Slicing Algorithm, Mat. Sci. Eng. A-Struct., 2021, 820, p 141539. https://doi.org/10.1016/j.msea.2021.141539CrossRef

46.

W. Li, L. Yan, X. Chen, J. Zhang, X. Zhang, and F. Liou, Directed Energy Depositing a New Fe-Cr-Ni alloy with gradually changing Composition with Elemental Powder Mixes and PARTICLE size’ Effect in Fabrication Process, J. Mater. Process Tech., 2018, 255, p 96–104. https://doi.org/10.1016/j.jmatprotec.2017.12.010CrossRef

47.

B.R. Barbero, and E.S. Ureta, Comparative study of Different Digitization Techniques and their Accuracy, Comput. Aided Design, 2011, 43(2), p 188–206. https://doi.org/10.1016/j.cad.2010.11.005CrossRef

48.

R. Ghanavati, H. Naffakh-Moosavy, and M. Moradi, Additive Manufacturing of thin-Walled SS316L-IN718 Functionally Graded Materials by Direct Laser Metal Deposition, J. Mater. Res. Technol., 2021, 15, p 2673–2685. https://doi.org/10.1016/j.jmrt.2021.09.061CrossRef

49.

D. Verdi, M.A. Garrido, C.J. Munez, and P. Poza, Microscale Effect of High-Temperature Exposition on Laser Cladded Inconel 625-Cr3C2 Metal Matrix Composite, J. Alloys Compd., 2017, 695, p 2696–2705. https://doi.org/10.1016/j.jallcom.2016.11.185CrossRef

50.

Y.M. Wang, T. Voisin, J.T. McKeown, J. Ye, N.P. Calta, Z. Li, Z. Zeng, Y. Zhang, W. Chen, T.T. Roehling, R.T. Ott, M.K. Santala, P.J. Depond, M.J. Matthews, A.V. Hamza, and T. Zhu, Additively Manufactured Hierarchical Stainless Steels with High Strength and Ductility, Nat. Mater., 2018, 17(1), p 63–71. https://doi.org/10.1038/nmat5021CrossRef

51.

H. Xiao, S.M. Li, X. Han, J. Mazumder, and L.J. Song, Laves Phase Control of Inconel 718 Alloy using Quasi-Continuous-Wave Laser Additive Manufacturing, Mater. Des., 2017, 122, p 330–339. https://doi.org/10.1016/j.matdes.2017.03.004CrossRef

52.

B. Chen, Y. Su, Z.H. Xie, C.W. Tan, and J.C. Feng, Development and Characterization of 316L/Inconel625 Functionally Graded Material Fabricated by Laser Direct Metal Deposition, Opt. Laser Technol., 2020, 123, p 105916. https://doi.org/10.1016/j.optlastec.2019.105916CrossRef

53.

E. Chauvet, P. Kontis, E.A. Jagle, B. Gault, D. Raabe, C. Tassin, J.J. Blandin, R. Dendievel, B. Vayre, S. Abed, and G. Martin, Hot Cracking Mechanism Affecting a Non-Weldable Ni-Based superalloy Produced by Selective Electron BEAM Melting, Acta Mater., 2018, 142, p 82–94. https://doi.org/10.1016/j.actamat.2017.09.047CrossRef

54.

X. Chen, J. Li, X. Cheng, B. He, H. Wang, and Z. Huang, Microstructure and Mechanical Properties of the Austenitic Stainless Steel 316L Fabricated by Gas Metal Arc Additive Manufacturing, Mater. Sci. Eng. A, 2017, 703, p 567–577. https://doi.org/10.1016/j.msea.2017.05.024CrossRef

55.

D.R. Feenstra, A. Molotnikov, and N. Birbilis, Effect of Energy Density on the Interface Evolution of Stainless Steel 316l Deposited Upon INC 625 via Directed Energy Deposition, J. Mater. Sci., 2020, 55(27), p 13314–13328. https://doi.org/10.1007/s10853-020-04913-yCrossRef

56.

M.S. Pham, B. Dovgyy, P.A. Hooper, C.M. Gourlay, and A. Piglione, The Role of Side-Branching in Microstructure Development in Laser Powder-Bed Fusion, Nat. Commun., 2020, 11(1), p 749. https://doi.org/10.1038/s41467-020-14453-3CrossRef

Titel: Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties
verfasst von: Xiaoyan Yu
Jiaxiang Xue
Qingkai Shen
Zehong Zheng
Ning Ou
Wei Wu
Publikationsdatum: 09.08.2022
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 3/2023
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-022-07158-9

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 3/2023

Comparison of Wear Performance of Low Temperature Nitrided and Carburized 316L Stainless Steel under Dry Sliding and Corrosive-Wear Conditions

Machinability Analysis of Composite Electrode Produced by Spark Plasma Sintering Process during Electro-Discharge Machining of Titanium Alloy

A Comparative Study on Conventional and Hybrid Quenching Hot Forming Methods of 22MnB5 Steel for Mechanical Properties and Microstructure

Constitutive Modelling and Processing Map of GH3128 Superalloy during Hot Deformation

Safety Assessment of Aircraft Panel under the Impact Load by Tire Fragment Based on Thermal–Mechanical Effect

Optimization and Prediction of Responses Using Artificial Neural Network and Adaptive Neuro-Fuzzy Interference System during Taper Profiling on Pyromet-680 Using Wire Electric Discharge Machining

Premium Partner

Marktübersichten