nach oben

Energy Efficiency

Erschienen in:

Open Access 05.07.2018 | Original Article

Simulating the deep decarbonisation of residential heating for limiting global warming to 1.5 °C

verfasst von: Florian Knobloch, Hector Pollitt, Unnada Chewpreecha, Vassilis Daioglou, Jean-Francois Mercure

Erschienen in: Energy Efficiency | Ausgabe 2/2019

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Patentsuche

Aus

Abstract

Whole-economy scenarios for limiting global warming to 1.5 °C suggest that direct carbon emissions in the buildings sector should decrease to almost zero by 2050, but leave unanswered the question how this could be achieved by real-world policies. We simulate which policy measures could induce an almost complete decarbonisation of residential heating, the by far largest source of direct emissions in residential buildings. Under which assumptions is it possible, and how long would it take? We use the non-equilibrium bottom-up model FTT:Heat to simulate policies for a transition towards low-carbon heating in a context of inertia and bounded rationality, focusing on the uptake of heating systems. Our results indicate that the near-zero decarbonisation is achievable by 2050, but requires substantial policy efforts. We find that policy mixes are more effective for incentivising the uptake of fuel-efficient low-carbon technologies, compared to a residential carbon tax as the only policy. In combination with subsidies and procurement policies for renewables, near-complete decarbonisation could be achieved with a tax of 50–200 €/tCO_2. Without being complimented by additional policies, carbon taxes show a decreasing marginal impact on total emission reductions, thus remaining insufficient for deep decarbonisation. In all scenarios, the decarbonisation of heating would increase projected heating costs faced by households initially, but could lead to cost reductions in most world regions in the medium term. We show that the potential impacts of policies highly depend on behavioural decision-making by households, especially in a context of deep decarbonisation and rapid transformation.

ESM 1 (XLSX 363 kb)

Electronic supplementary material

The online version of this article (https://doi.org/10.1007/s12053-018-9710-0) contains supplementary material, which is available to authorized users.

Introduction

Final energy demand in residential buildings was estimated to be 24 PWh/year in 2010, causing direct on-site emissions of 2.18 GtCO₂/year and indirect emissions from electricity use of 3.5 GtCO₂/year (Lucon et al. 2014). At the same time, plenty of unexploited mitigation options exist in buildings, many at low (or even negative¹) cost (Ürge-Vorsatz et al. 2012a). For limiting global warming to 2 °C, all transformation pathways reviewed in IPCC-AR5 therefore suggest substantial reductions of the buildings sector’s direct carbon emissions: around 50–75% until 2050 and up to 100% by 2100 (Clarke et al. 2014). Limiting global warming to 1.5 °C implies a lower remaining budget for cumulative economy-wide emissions (730–880 GtCO₂ from 2015 to 2100, Millar et al. 2017) and therefore requires to reach net-zero carbon emissions as early as mid-century (Rogelj et al. 2015). Because remaining decarbonisation options compared to 2 °C pathways are limited, scenarios for reaching the 1.5 °C target rely much more strongly on rapid emission reductions in the buildings sector: around 85–95% by 2050, relative to their current level (Rogelj et al. 2015). While such pathways indicate what may be optimal from a social planning perspective, they strongly focus on the supply side of the energy system, leaving open the question how such a deep decarbonisation could be achieved by real-world demand-side policies, and which timescale would be realistic.

It is estimated that 56% of final energy in residential building is used for space and water heating, of which 55% is generated by fossil fuels, around 30% by biomass, and 15% by electricity and district heating systems (IEA 2013a). Heating is thus by far the largest energy end-use in households, and responsible for most of residential on-site CO₂ emissions. Despite that, it only receives relatively limited policy attention compared to the electricity and transport sectors (IEA 2014). While the theoretical emission reduction potential is well-known (Ürge-Vorsatz et al. 2012b), it remains unclear which real-world policy instruments could reduce the sector’s CO₂ emissions to near-zero sufficiently fast.

There is a consensus that the global demand for heating can be fulfilled much more energy efficiently, thereby reducing fuel use and emissions without reducing comfort (Lucon et al. 2014). Heating loads can be reduced by an improved thermal insulation of houses, and the remaining heat demand can be serviced by renewable and energy-efficient technologies. Through their integrated application, building energy use can be reduced by up to 90% compared to conventional buildings (Urge-Vorsatz et al. 2013; Ürge-Vorsatz et al. 2012a). Given that 50% of the current building stock will still be in use by 2050 (75% in OECD countries) (IEA 2013b), levels of building efficiency in the next decades strongly depend on building shell retrofits of existing houses (Ürge-Vorsatz et al. 2012b, 2015b).

Aside from space heating, over 40% of global heat demand is for water heating, which is less impacted by insulation (Connolly et al. 2014), but likely to rise with growing income in many world regions (Daioglou et al. 2012). Near-zero-emissions are thus unachievable as long as the remaining heat demand is not provided by renewable and efficient electricity-based technologies. Available alternatives to fossil fuel heating systems rely on the use of biomass (traditional or in modern boilers), electricity (e.g. electric resistance or immersion heating), ambient heat (heat pumps) or solar energy (solar thermal panels) (for an overview, see IEA 2014). While the operation of solar and biomass systems can potentially be carbon neutral (abstracting from life-cycle considerations²), heating with electricity can be a renewable technology once electricity generation is decarbonised; otherwise, electricity-related emissions must be accounted for. A much more efficient use of electricity can be achieved by heat pumps, which upgrade the ambient low-temperature energy of an air, water or ground source into higher-temperature heat for space and water heating, effectively achieving efficiencies of 200–400% (average ratio of heat output to electricity input) (for an overview, see IEA/ETSAP and IRENA 2013). The cost-competitiveness of these capital-intensive renewable technologies, with respect to incumbent fossil fuel technologies, strongly depends on a combination of local circumstances (such as local electricity and fuel prices, solar irradiation), generally not achieved in most countries.

The potential of modern renewable heating technologies remains largely unexploited: their combined use (excluding heat pumps) accounted for less than 5% of global heat generation in 2012 (for a market overview, see IEA 2014). Some countries have introduced policy instruments and market and institutional conditions for incentivising their uptake, most commonly in the form of capital subsidies (e.g. in Austria and China), carbon taxes (e.g. in Northern Europe) and use obligations (e.g. in Germany and Spain) (Connor et al. 2013; Ürge-Vorsatz et al. 2015a). Due to such policy support, an increased diffusion of renewables can be observed in some places (such as solar thermal heating in China): from 2010 to 14, their combined market share grew by 8% (International Energy Agency 2017). While progress of the observed extent can improve the energy efficiency of heating incrementally, it is insufficient for achieving large absolute reductions in CO₂ emissions, which thus require more ambitious policy approaches (Jotzo et al. 2012; Mundaca et al. 2013a, b; Mundaca and Markandya 2016; Wilhite and Norgard 2004).

Planning for a technological transition in the heating sector requires information on policy strategies that can generate the right level of incentive to achieve the required changes in consumer choices. In this paper, we focus on analysing the diffusion of renewable and efficient heating technologies in terms of various possible choices of realistic composite policy packages, in 59 regions of the world. Which policy mixes could induce a sufficiently fast transition towards renewable heating, under which conditions and behavioural assumptions, and how long would it take? In a first step, we use the IMAGE-REMG model (Daioglou et al. 2012; Isaac and van Vuuren 2009) to project trends of residential heating demand until 2050. Our focus, however, is on the future technology portfolio, which depends on the choice of heating technologies by households.

We project household choices of heating technologies using the ‘Future Technology Transformations’ model FTT:Heat (Knobloch et al. 2017). It is a bottom-up simulation model of technology diffusion, aiming to project how the technology composition of residential heating systems in 59 world regions may develop until 2050 under the chosen assumptions on heat demand and choice behaviour. Based on projected preferences and decisions, the model simulates which technologies supply which share of the heating market and estimates the resulting levels of fuel use and emissions. It is designed to simulate the potential impact of various sets of possible policy strategies.

The paper is structured as follows. In section ‘Background and literature’, we review the literature, and in section ‘Methods and data’, we present our model and data. Policy scenarios and results of the model simulations are presented and discussed in section ‘Results’. Section ‘discussion and conclusion’ concludes.

Background and literature

Residential heat generation is overwhelmingly small scale and distributed, taking place on site within homes. The uptake of new heating equipment depends on the individual decision-making by heterogeneous households, each with subjective preferences and perceptions, and only limited information, time and cognitive capacities to evaluate alternative options. At the system level, the sum of such decisions inevitably deviates from the least-cost optimum as it would be determined by models that assume a single, fully rational agent or social planner (Kirman 1992), leading to the criticism that many bottom-up energy-models are based an unrealistic representations of real technology choice-making (for reviews, see Mundaca et al. 2010; Wilson and Dowlatabadi 2007; Worrell et al. 2004). Avoiding costly policy-design failures requires an upfront simulation of policy effects, based on an analysis that better represents people’s actual behaviour under bounded rationality and limited information, and accounting for non-linear diffusion dynamics (Mercure et al. 2016; Rai and Henry 2016). A behavioural modelling of decision-making is particularly relevant for policies aiming at a premature replacement of existing systems, which will likely be necessary for deep decarbonisation (Geels et al. 2017). For instance, in such decisions, households are found to apply very strict payback thresholds (Newell and Siikamki 2015; Olsthoorn et al. 2017), reflected in high implicit discount rates as estimated from consumer choices (Hausman 1979; Schleich et al. 2016; Sutherland 1991; Train 1985). In this section, we review the aspects relevant to building a simulation-based diffusion model that takes into account known behavioural features of decision-making.

Household decision-making

Applied behavioural research shows that household decisions between different heating systems are driven by a diverse set of individual preferences and behavioural characteristics (for a review, see Kastner and Stern 2015). Multiple studies find that main determinants of investments in heating systems are related to costs (Achtnicht and Madlener 2014; Lillemo et al. 2013; Sopha et al. 2011). Other significant factors are the influence by social norms, and social comparisons with peers (Hecher et al. 2017; Sopha et al. 2010). Michelsen and Madlener (2012) find that preferences depend on sociodemographic (e.g. age, education), spatial (e.g. urban/rural) and home characteristics (e.g. home type, size). Wilson et al. (2015) point out that energy efficiency investments should not be seen in isolation, but as processes that emerge from social practices. Psychological and sociological research points to the behavioural relevance of norms, attitudes, values, motivation and social influence, all of which can impact technology choice (Abrahamse et al. 2005; Abrahamse and Steg 2009; Clayton et al. 2015; Dietz et al. 2009; Steg 2008; Stern 1986; Wilson and Dowlatabadi 2007).

The heterogeneity of household characteristics and perceptions may partly explain the ‘energy efficiency gap’ (Allcott and Greenstone 2012; Jaffe and Stavins 1994) between a hypothetical optimum as seen from an outside economics-engineering perspective and observed household decisions, which seem to undervalue future energy savings relative to upfront investment costs, resulting in a typically lower than expected uptake of energy-efficient technologies (reflected in high empirical estimates of implicit discount rates, as reviewed by Hausman 1979; Train 1985). Various explanations are discussed in the literature (for a review, see Gillingham and Palmer 2014), which can be grouped into market barriers (e.g. hidden costs), market failures (e.g. asymmetric or imperfect information, split incentives) and systematic behavioural biases, as described by behavioural economics (e.g. loss aversion, sub-optimal decision heuristics, status quo bias, saliency, procrastination) (Allcott and Mullainathan 2010; Bager and Mundaca 2017; Frederick et al. 2002; Kahneman and Tversky 1979; Lillemo 2014; Shogren and Taylor 2008; Simon 1955).

The cumulative effect of household heterogeneity, imperfect information and social influence implies that the diffusion of new technologies does not happen instantaneously once they become economically attractive, but typically follows an S-shaped trajectory (Rogers 2010): a slow initial growth is driven by a small group of early adopters, eventually followed by the large majority and, finally, laggards. The process is further amplified by learning-based gradual cost decreases once a technology grows in market share (Weiss et al. 2010), the nature and scale of transaction costs (Mundaca et al. 2013a, b) and industrial dynamics (e.g. capacity constraints, see Wilson 2012). For energy technologies, these up-scaling dynamics have been extensively studied (Grübler et al. 1999; Wilson and Grubler 2011), emphasising the significance of formative phases and path dependence. The resulting technology transitions usually take decades rather than years, being accompanied by changes in regulation, infrastructure, user practices and culture (Geels 2002). Hence, policies aiming at transitions must be designed with an understanding of how new technologies slowly diffuse out of niches and of households’ diverse motivations to adopt and use them.

Modelling of the diffusion of heating systems

Various types of energy end-use models exists, which can be grouped into various categories, such as accounting-based, optimisation, agent-based or bottom-up (Mundaca et al. 2010; Worrell et al. 2004), each with different (or sometimes no) representations of decision-making (Wilson and Dowlatabadi 2007). Many national or global level energy-economy models (such as integrated assessment models) are of normative nature, used for analysing the cost-effectiveness (e.g. TIMES, MESSAGE) or cost-benefit ratio (e.g. FUND, PAGE, DICE) of technology pathways from a social planning perspective (Li et al. 2015).³ While such an approach can be insightful for exploring cost-effective technology pathways, optimisation models mostly neglect behavioural, social and industrial dynamics, effectively assuming that a single representative agent with perfect information and foresight is taking the decisions. The analysis of how (and if) a scenario can be achieved with which types of incentives requires simulation models that better capture some of the complex interactions between heterogeneous agents (Mercure et al. 2016), and some of the salient behavioural features involved in real decision-making, a need which is also highlighted in IPCC-AR5 (Kolstad et al. 2014).

For the heating sector, some attempts have been made to introduce a representation of household behaviour into optimisation bottom-up models of technology uptake. Cayla and Maïzi (2015) extended the TIMES-Households model for France by including different household categories. Also for France, Giraudet et al. (2012) introduce consumer heterogeneity and intangible costs into a bottom-up sub-module of IMACLIM-R. Li (2017) presents an optimisation model with heterogeneous decision-making which covers heating in the UK. However, most of these studies feature a relatively low resolution of technology types for heating and are restricted to one (or mostly a few) countries. Furthermore, the behaviour represented typically comes in the form of frictions or externalities (e.g. using higher discount rates) introduced to prevent the models from reaching their otherwise normative optimal technological configurations.

As an alternative to optimisation, several authors have developed agent-based models (ABMs) of heating system uptake, such as Sopha et al. (2011) for wood pellet heating in Norway. While the approach allows the simulation of heterogeneous households, non-standard decision-making and social influences, the calibration of ABMs requires a rich set of socioeconomic data, usually generated by household surveys and interviews, which implies challenging requirements for their application on a larger scale (Rai and Henry 2016). A more qualitative approach of analysis is taken in the ‘Energy Efficiency in Buildings’ model, which provides a replicable methodology for local market analysis (WBCSD 2016).

A modelling approach of intermediate complexity is the use of discrete choice models with multinomial logit structures for representing household diversity, such as the CIMS model for energy demand in Canada (Rivers and Jaccard 2005), the Invert/EE-Lab model for building-related energy demand in selected European countries (Kranzl et al. 2013; Stadler et al. 2007) and the bottom-up models of household energy use by Van Ruijven et al. (2011) and Daioglou et al. (2012) (together forming the REMG model component of IMAGE, see section ‘Simulating future heat demand with IMAGE-REMG’), differentiating for urban and rural households and including income distributions. Some of these models are technology-rich and coupled with detailed building-physics models of the housing stock (e.g. Invert), which increases their degree of realism from an engineering perspective. At the same time, the data requirements are immense, so that models either tend to focus on a limited set of countries (CIMS and Invert) or only have limited technology representation (IMAGE-REMG).

Modelling the global scale is crucial in questions related to climate targets, as it is the only way to calculate global emissions required to estimate climate change. We acknowledge the difficulties to include (and parameterise) behavioural dynamics and diversity with only limited data available at the global scale, given that such behavioural features must vary by country. In FTT:Heat, we therefore choose a compromise: heterogeneous decision-making and social dynamics are represented in a stylised but tractable way. To the best of our knowledge, there exists so far no similar simulation model for the diffusion of heating systems at the global scale. This enables FTT:Heat to be made into a component of a new type of integrated assessment model, E3ME-FTT-GENIE (Mercure et al. 2018).

Methods and data

Simulating future heat demand with IMAGE-REMG

First, we use the IMAGE-REMG model to project future changes in heat demand (UE_tot), directly after the methodology described in Isaac and van Vuuren (2009) and Daioglou et al. (2012). Demand levels are projected for (i) a baseline scenario, (ii) a mitigation scenario consistent with limiting radiative forcing to 1.9 W/m² (1.5 °C target), involving increased efficiency of new buildings, and (iii) a variant of the mitigation scenario which additionally assumes increased retrofitting of existing houses.

IMAGE-REMG projects UE_tot as the sum of demand for space and water heating. For water heating, future demand per person is modelled as a function of income, converging to a maximum saturation value which depends on heating degree days (HDD) (Daioglou et al. 2012). For space heating, demand is modelled as a function of population, floor space per person (m²/cap), heating degree days (HDD) and the useful energy heating intensity (UE/m²/HDD) (Isaac and van Vuuren 2009):

$$ {UE}_{space}=\mathrm{Population}\times {\mathrm{m}}^2/\mathrm{cap}\times \mathrm{HDD}\times UE/{\mathrm{m}}^2/\mathrm{HDD} $$

(1)

Future changes in population, climate and income are exogenous drivers, based on the SSP (Shared Socioeconomic Pathway) 2 (‘middle of the road’) (see Riahi et al. 2017). The mitigation scenario (SSP2–1.9) projects reductions in heating intensity which would be consistent with achieving the 1.5 °C target, which implies an improved thermal insulation of houses (e.g. by means of building standards and retrofits). Floor space is an intermediate driver, calculated as a function of income and population density. HDD are derived from monthly mean temperatures, taking into account future levels of global warming. All relevant data is publicly available via the IMAGE website (including future trends in m²/cap, HDD and UE_space) (PBL 2018).

Heating intensity foremost depends on heating practices and levels of building insulation, with current values ranging from 50–150 kJ_UE/m²/HDD. The IMAGE-REMG model treats residential energy demand on aggregate, not specifically modelling building stocks, retrofitting or specific technology/efficiency standards. Instead, the heating demand is exogenously driven based on scenario assumptions, not attached to specific actions. In the SSP2 scenario, the heating intensity of all houses is assumed to decrease towards an average of 90 kJ_UE/m²/HDD by 2100 in all world regions (from 100 to 150 kJ_UE/m²/HDD by 2015) or remains at the current level if this is lower, meant to reflect the improvement of worst performing buildings with a convergence towards current average intensities. In the SSP2–1.9 scenario, it is assumed that the heating intensity decreases to 60 kJ_UE/m²/HDD by 2100 (corresponding roughly to the ‘sub-optimal’ scenario in the GEA, see Ürge-Vorsatz et al. 2012a), consistent with the assumption that aggregate insulation efficiency increases (e.g. in reaction to more stringent building regulations). Last but not least, the retrofitting scenario assumes that the heating intensity decreases towards 45 kJ/m²/HDD by 2050. This would be consistent with rapid insulation improvements of the existing building stock.⁴

Simulating technology uptake with FTT:Heat

The core of FTT:Heat is a simulation of technology diffusion, in which individual heating technologies (e.g. gas boilers, heat pumps) compete for market shares of the total heat demand. Importantly, the model does not minimise or maximise some objective function, such as system cost or intertemporal utility. Instead, it simulates the decision-making of households: under given behavioural assumptions and levels of heat demand, which heating technologies would they choose, and how fast can new technologies grow within the market?

Initial market shares of individual technologies i, S_i(t), are calculated from historic data on heat generation by technology i, UE_i(t), as:

$$ {\displaystyle \begin{array}{l}\\ {}{S}_i(t)=\frac{UE_i(t)}{UE_{tot}(t)},\kern0.5em \sum \limits_i{S}_i(t)=1\end{array}} $$

(2)

At every time step Δt of the simulation (set to 1/4 year), FTT:Heat models the change in future market shares based on three central elements (further described below):

Decision-making by diverse households

Dynamic growth of technologies

Learning by doing

From the resulting shares, the model projects the new levels of useful energy demand per technology, UE_i(t).

UE_i can change when the total demand for heating (UE_tot) changes (e.g. due to improved levels of thermal insulation) and/or when the technology composition (S_i) changes (e.g. due to ongoing trends in technology uptake or due to the introduction of new policies). Final energy demand, fuel use and capacities are then estimated based on technology-specific conversion efficiencies and capacity factors (also depending on the climate). Negative changes in a technology’s capacity correspond to decommissions that are not replaced. Finally, on-site CO₂ emissions are calculated from projected fuel use, based on the respective carbon content.

Decision-making by diverse households

In each simulation period (set to ¼ year), a fraction of households decides between heating systems: either for replacing existing systems that come to the end of their lifetime (or became so expensive to operate that they are replaced ahead of that) or to satisfy new demand.

For systems coming to the end of their lifetime, FTT:Heat simulates a pairwise comparison of all available heating technologies by heterogeneous households, based on distributed costs and preferences. These are represented as the generalised cost of heating, GCOH_i:

$$ {GCOH}_i={LCOH}_i+{\gamma}_i $$

(3)

GCOH_i consists of two parts: an engineering-based annualised levelised cost calculation (LCOH_i) and an empirical estimate of technology characteristics which are valued by households (based on observed technology uptake), γ_i. Levelised costs are calculated for all technologies, as:

$$ {LCOH}_i={\sum}_t\frac{\frac{IC_{i,t}}{CF_i}+\frac{MR_{i,t}}{CF_i}+\frac{FC_{i,t}}{CE_i}}{{\left(1+r\right)}^t}/{\sum}_t\frac{1}{{\left(1+r\right)}^t} $$

(4)

IC_i,t, MR_i,t and FC_i,t are upfront investment costs, maintenance-repair costs and the fuel price respectively. CF_i is the capacity factor (depending on a region’s heating degree days), and CE_i the technological conversion efficiency (output of useful heat, relative to input of fuel). t is the time period, and r is the discount rate. It is meant to describe how households value future relative to present costs, using a rate of 9%, based on Jaccard and Dennis (2006) (a sensitivity analysis is given in Table 2).⁵ In addition, policies can be imposed, such as a carbon tax or a capital subsidy.

As a representation of household diversity, IC_i,t, MR_i,t and FC_i,t are all distributed around their mean values. Such diversity originates from different individual characteristics of the household, the technology or the dwelling. Accordingly, LCOH_i is not treated as a unique value, but as a frequency distribution with a mean and a standard deviation (illustrated in the left panel of Fig. 1), combined using standard error propagation:

$$ \Delta {LCOH}_i=\sqrt{\frac{\varDelta {IC}_i^2}{CF_i^2}+\frac{\varDelta {MR}_i^2}{CF_i^2}+\frac{\varDelta {FC}_i^2}{CE_i^2}} $$

(5)

Many additional aspects may be valued by households which remain unspecified in the LCOH_i, such as the perceived inconvenience of a technology (e.g. for pellet heating, see Sopha et al. 2010), possible co-benefits (e.g. using a heat pump for cooling purposes) or existing policies. We refer to such aspects as ‘intangibles’, the value of which is represented in the technology- and region-specific empirical parameter γ_i. It is derived using a calibration with historical diffusion data: we search for the set that makes the rate of diffusion continuous at the cross-over between historical and simulation periods, in each region (a description of the methodology is given in the appendix). The values of ‘intangibles’ may change over time. However, we cannot estimate their future values before new data on technology uptake becomes available. We therefore assume that ‘intangibles’ remain constant throughout the simulation period.

For a population of heterogeneous households, the comparison of two technologies is then performed by comparing the frequency distributions of their generalised cost:

$$ {F}_{ij}\left(\Delta {C}_{ij}\right)={\int}_{-\infty}^{\infty }{F}_j(C){f}_i\left(C-\Delta {C}_{ij}\right) dC\kern0.5em \Delta {C}_{ij}={GCOH}_i-{GCOH}_j $$

(6)

F(C) and f(C) are the cumulative cost distribution function and the cost distribution density, respectively. F_ij denotes the fraction of households preferring technology i over technology j. It is calculated as the fraction of households for which the GCOH with technology i is less than with technology j (i.e. the model calculates a binary logit). For example, if F_ij = 0.7, 70% of households in this region would prefer technology i over j, while 30% have the reverse preference. The comparison is performed for all possible pairs of available technologies, resulting in a complete order of distributed household preferences, summarised in the matrix F (which is endogenously calculated for all regions and updated in each simulation period). The diversity of choices implies a differentiation of the market, in which households take different decisions at different points in time for different reasons, as described by diffusion theory (Rogers 2010).

Technology diffusion dynamics

Once preferences are estimated, the change in technology shares is simulated (Mercure 2012, 2015). First, we derive the substitution of market shares from heating technology j to i in period Δt, as:

$$ \Delta {S}_{j\to i}={S}_j{F}_{ij}{\tau}_j^{-1}{S}_i\Delta t $$

(7)

Substitutions from j to i depend on the fraction of households who would prefer technology i over j (the preference matrix F_ij, which is newly estimated in each period), the previous market shares of both technologies (S_i and S_j), and the fraction of technology j which needs to be replaced (estimated as the inverse of its average technological lifetime, τ_j).⁶

Since preferences are diverse, another fraction of households may have the reverse preference and would choose technology j over i. We thus calculate the net substitution from technology j to technology i.⁷ Finally, the sum of all such pairwise comparisons over all competing technologies j yields the cumulative net change in market shares of technology i:

$$ \Delta {S}_i=\sum \limits_j{S}_i{S}_j\left({F}_{ij}{\tau}_j^{-1}-{F}_{ji}{\tau}_i^{-1}\right)\Delta t $$

(8)

Formula (8) is the non-linear dynamic shares equation, conceptually similar to the modelling of imitation dynamics in evolutionary game theory (Hofbauer and Sigmund 1998), originating in the description of evolutionary competition between different species. Each single flow from a technology j to an alternative technology i is determined by three interacting elements:

Preferences (F_ij): which fraction of households would prefer which technology, given that they were to buy a heating system within period Δt?

II.

Replacement needs $ \left({S}_j{\tau}_j^{-1}\right) $: how many heating systems of technology j need replacement in period Δt?

III.

Dynamic constraints (S_i): given preferences and replacement needs, which fraction of substitutions can be realised?

Substitutions are dynamically constrained, as a stylised representation of (a) limited capacities to produce and install new technologies and (b) limited information and behavioural decision-making on part of households. Psychological research reports that households typically do not optimise, but tend to stick to the status quo, are impacted by prevalent social norms or follow the behaviour of others (Abrahamse and Steg 2013; Frederiks et al. 2015). For heating systems, the main information sources are interpersonal sources and installers (Mahapatra and Gustavsson 2008). For the diffusion of innovations, industrial and social dynamics are self-reinforcing, and both make it more likely that households choose dominant technologies. We represent these dynamics by constraining a technology’s growth by its market share (S_i), based on Mercure (2015, 2017).

As a central implication, technology transitions in the model are subject to inertia, as technological trajectories cannot change direction rapidly, and resembles S-shaped diffusion curves. While undoubtedly remaining a stylised representation of underlying behavioural, social and industrial dynamics, it is an improvement in comparison to exogenous growth constraints in standard optimisation models, since here the constraint is fully endogenous.

Substitutions can be further constrained to account for behavioural and technical plausibility/feasibility. We follow Kranzl et al. (2013) and assume that households would not switch back to technologies with a much lower comfort level, i.e. that households with modern heating systems (such as district heat, gas, electricity) would not go back to coal or traditional biomass.

Finally, new levels of heat generation per technology (UE_i) are obtained by multiplying their new shares by a region’s total heat demand (UE_tot) (modelled by IMAGE-REMG).

Premature replacements

Equation (8) would suggest that households replace heating devices only at the end of their lifetime. However, in reality, households may consider to replace functioning heating systems ahead of that, based on economic considerations. For a household with perfect information and without risk-aversion, this would be beneficial once the marginal running costs of operating the current system exceed the full levelised costs of buying and operating an alternative technology. In practice, it is known that households apply much stricter criteria and only consider a premature replacement if the potential savings exceed the initial investment in a limited period of time—the so-called payback threshold (Gillingham and Palmer 2014).

Thus, in the model, premature replacements are only considered as sufficiently attractive if (and only if) the savings (due to reduced operating costs, MC_i) exceed the investment costs of another technology (IC_j, inclusive of an eventual subsidy) within the considered payback time (b), so if:

$$ {MC}_i>{MC}_j+{IC}_j/b $$

(9)

Given the costs, decisions strongly depend on the assumed value of b. In choice experiments, Olsthoorn et al. (2017) find that the mean payback threshold for a premature replacement of space heating systems is as low as 3 ± 1 years, while Newell and Siikamäki (2015) report a mean threshold of 3–5 years. Assuming that this applies to all regions, we use 3 ± 1 years. A sensitivity for b is given in section ‘Dynamics in an exemplary decarbonisation scenario’.

Learning by doing

We endogenously model cost reductions in upfront investment costs over time, IC_i(t), which occur due to the accumulation of knowledge and experience (‘learning by doing’), leading to the empirically well-described phenomenon of learning curves. Endogenous cost reductions increases path dependence in technology diffusion (Arthur 1989), leading to increasing returns to scale for growing technologies.

In each period, updated investment costs are calculated as a function of the increase in cumulative global capacity of a technology, based on technology-specific learning rates: they describe the relative cost reduction that is expected for every additional doubling of the global capacity. We use learning rates from a review of empirical evidence by Weiss et al. (2010) (given in the appendix).

Economic feedbacks

FTT:Heat is hard-linked to the macroeconometric global simulation model E3ME (Cambridge Econometrics 2014), most importantly via variables for fuel use and household expenditures. Policies which are primarily targeted at the heating sector can lead to changes in households’ demand for different fuels or to higher expenses for heating systems. For each year of the simulation, E3ME projects the wider macroeconomic impacts of such effects and allows to analyse the implications for other economic sectors. We focus on the impact on electricity generation: policies for household heating can lead to changes in a region’s electricity demand and thereby impact the power sector, leading to changes in its fuel use and CO₂ emissions. Such effects are endogenously simulated by FTT:Power, which is hard-linked to FTT:Heat via the E3ME model (Mercure et al. 2014, 2018).

Energy demand

Only limited data is available on the specific demand for residential heating, the related fuel consumption and technology composition (IEA 2014; Lucon et al. 2014). We combine data on fuel use and technology diffusion from various sources and provide the resulting database as SI.

Final energy demand for heating in EU countries is taken from the ODYSSEE database (Enerdata 2017), which contains annual data for space and water heating in all 28 member states. For non-EU regions, the IEA energy statistics report final residential energy demand by fuel type, but do not differentiate by end-use application (IEA 2017). The share of heating in household energy demand strongly depends on climatic conditions and levels of building insulation, ranging from 10% India to 87% in Russia, with water heating being of dominant importance in warmer climates (IEA 2013a). We calculate the shares of heating for ASEAN, Brazil, China, India, Mexico, Russia, South Africa and the USA based on estimates in IEA (2013a) and country-specific sources (Daioglou et al. 2012; Eom et al. 2012; Wang and Jiang 2017). For sub-Saharan Africa, we adjust the fuel use data to bottom-up estimates of heat demand by the IMAGE-REMG model. For remaining world regions, the heating share is estimated based on heating degree days, assuming a comparable heating intensity as in world regions with a similar climate.

Residential heat generation by solar thermal installations for most world regions is available in the IEA energy statistics, which we amended by data from the IEA Solar Heating Programme (Mauthner et al. 2016). No standardised global data exists on heat generation by heat pumps. For most EU countries and Norway, time series were available from the European Heat Pump Association (2016), which was amended by data from EurObserv’ER (2017). For other world regions, the heat generation by ground-source heat pumps is taken from Lund and Boyd (2016). Data on the use of air-source heat pumps is taken from country-specific sources where available (China Heat Pump Committee of China Energy Conservation Association 2015 for China; EIA 2017 for the USA; Japan Refrigeration and Air Conditioning Industry Association (JRAIA) 2017 for Japan; Kegel et al. 2014 for Canada; Lapsa et al. 2017 for the USA).

In the model, data on final energy demand (E_i) is transformed into useful energy demand (UE_i) according to technology-specific conversion efficiencies (CE_i) (see Appendix-Table 5), so that:

$$ {UE}_i(t)={E}_i(t)\times {CE}_i\kern0.50em $$

(10)

The resulting top-down estimate of heat demand has to be seen as a simplification, owing to the absence of reliable information on residential energy end-use in most world regions, and is subject to the uncertainty of underlying data and assumed efficiencies.

We estimate that in 2014, global final energy demand for residential space and water heating was around 12 PWh, useful energy demand 9.6 PWh, direct on-site CO₂ emissions 1.5 GtCO₂/year (around 70% of reported direct residential building sector emissions in 2010, Lucon et al. 2014) and indirect emissions in the electricity sector 0.5 GtCO₂/year.

Technology data

Cost and performance data for the 13 different kinds of heating technologies is summarised in Appendix Table 5. Country-specific Investment costs (incl. of installation) for EU countries are taken from Fleiter et al. (2016) and Connolly (2014). For other world regions, we estimated the relative differences in investment costs from levels of real available household income. A standard deviation equivalent to 1/3 of the mean cost is assumed for all technologies (Danish Energy Agency 2016, based on cost ranges reported by 2013; NREL 2016). Residential fuel prices are taken from the IEA (2016a), with an assumed standard deviation of 15% (30% for biomass, based on NREL 2016). More details and the data are given in the appendix.

Scenario definition

We created ten model scenarios (labelled a–j) aiming at a decarbonisation of residential heating until 2050, all of which use a different set of policies, implemented from 2020 onwards. Scenario a is our baseline projection, without improved insulation of the building stock (SSP2). It includes a continuation of current policies, the effect of which is implicitly included in the γ_i parameters. Scenario b assumes increased levels of thermal insulation for new houses (SSP2–1.9), which often is the prerequisite for an effective use of renewables. In scenario c, we simulate the additional effects of having more ambitious retrofitting of existing buildings, leading to further demand reductions. In addition to the improved insulation levels of scenario c, scenarios d–i explores policy instruments which are aimed at the uptake of heating technologies: a residential carbon tax, technology subsidies and ‘kick start’ schemes for new technologies. These policies were chosen based on their successful previous implementation in at least some countries (for an overview, see Connor et al. 2013; IEA 2014), as well as from advice from policy analysts at the European Commission. Scenario j explores complete electrification. We assume the political acceptability of the simulated policies for the purpose of our analysis. The gap between the modelled carbon tax levels and levels observed in reality reflects the political economy of carbon pricing mechanisms.

The (sectoral) carbon tax is specified as an absolute increase in the household price of fossil fuels, relative to their respective carbon content (we do not assume an inclusion of households into emissions trading).⁸ We simulate carbon taxes of 50 €/tCO₂ (scenario d) and 100 €/tCO₂ (scenario e). From 2020 to 2050, the tax is assumed to linearly increase by + 10% per year, relative to its respective starting value (reaching 200 €/tCO₂ and 400 €/tCO₂ in 2050). The 50 €/tCO₂ tax is equivalent to fuel price increases of around + 0.01 €/kWh for gas, + 0.013 €/kWh for oil and + 0.018 €/kWh for coal. In practice, such a tax may also take the form of subsidy removal in countries where household fuel use is currently subsidised (e.g. in form of reduced VAT rates, such as on domestic fuel use in the UK⁹).

II.

Technology subsidies are defined as a relative reduction in a renewable heating technology’s mean upfront investment cost. Eligible are solar thermal, heat pumps and modern biomass. Two subsidy rates are simulated: − 25% (scenario f) and − 50% (scenario g). We assume that subsidy rates remain constant from 2020 until 2030 and are linearly phased out afterwards, reaching zero in 2050.

III.

A kick start policy is not market-based, but represents a policy measure that introduces a new technology by means of a procurement scheme, use obligation in building codes or other regulation. Such a policy is useful for driving initial markets in countries where a new technology’s uptake is very limited or absent so far, thereby limiting the spread of relevant first-hand experiences between households and preventing the build-up of necessary expertise and capacity in the building and heating industries. Precedents for such policies can be found in Spain and Germany, amongst others (Connor et al. 2013). In the model, we represent such a policy for limited time periods (5–10 years) by assuming that in each year, one percentage point of the dominant fossil fuel technology’s market share is replaced by a mix of renewable alternatives.

Scenarios d–g focus on single policy instruments, while policy mixes involving two or more policies are simulated in scenarios h–j.

For all scenarios, we assume constant energy prices, for two reasons: first, future energy prices are highly uncertain, especially in a context of global deep decarbonisation. Effectively, this makes constant prices as likely as any other scenario. Second, it allows for a clearer identification of policy effects, which may otherwise be convoluted with the effects of a change in energy prices. A sensitivity analysis shows that our results do not substantially differ under increasing and decreasing future energy prices and other parameters (see Table 2).

In all scenarios, solar thermal is limited to the demand of water heating in each country (as it is mainly used for water heating and only as a supplementary source for space heating). District heating is only an option in those regions where it already exists (we do not assume the construction of new heat networks, which could well be an alternative to decentralised renewable heating in some regions).

Results

Heat demand

We first estimate future residential demand for space and water heating under different assumptions on future building efficiency and retrofitting, by applying projected demand trends from IMAGE-REMG to the historically estimated heat demand in 2014. Figure 2 depicts the resulting baseline demand trends by world region (SSP2, in which heating intensity globally converges to 90 kJ/m²/HDD by 2100), a scenario of improved efficiency of newly built houses (SSP2–1.9, in which heating intensity globally converges to 60 kJ/m²/HDD by 2100), and a scenario which additionally assumes increased levels of retrofitting of the existing building stock (assuming a decrease to a heating intensity of 45 kJ/m²/HDD by 2050). It becomes evident that changes in future global demand strongly depend on China, which currently still shows very low levels of average heating intensity. Large demand increases are projected with continuously rising income, which may still be limited by improved building efficiency of newly built housing stock. Projected increases in warmer world regions mainly reflect growing demand for water heating, which empirically depends on income, and is unaffected by our assumptions on housing insulation. Estimated effects of retrofitting are largest in Western Europe and North America, where heat demand remains high, but is largely saturated.

Environmental effectiveness of policies

The main results for policy scenarios a–j are illustrated by Fig. 3, which shows the projected global technology composition (left) and CO₂ emissions (right) until 2050. Indirect CO₂ emissions from electricity use are projected by FTT:Power, assuming a power sector decarbonisation scenario that is consistent with limiting global warming to 1.5 °C (the projected emission intensities on the global level are shown in the appendix and are reported for all regions in the SI). In addition, dashed lines show the total emission levels under current trends of power sector decarbonisation. Table 1 presents the cumulative changes in CO₂ emissions from 2020 to 2050. In the appendix, we show the underlying projected changes in the fuel mix, as well as the induced technology diffusion for five major world regions.

Table 1

Cumulative 2020–2050 CO₂ emissions, by residential heating and electricity generation for residential heating, in gtco₂. The top row shows absolute values in the baseline scenario (a), the following rows the changes relative to baseline in scenarios with improved insulation and heating decarbonisation (b–j). Emissions by electricity generation are shown for a scenario with a power sector decarbonisation trajectory consistent with limiting global warming to 1.5 °C (i) and a scenario without further decarbonisation of the power sector (ii)

	Scenario	Residential heating	Electricity generation for heating		Heating + electricity
	Scenario	Residential heating	(i) Decarbonisation	(ii) Baseline	(i) Decarbonisation	(ii) Baseline
Baseline (GtCO₂)	a	51 Gt	9 Gt	26 Gt	60 Gt	78 Gt
Diff. to baseline (ΔGtCO₂)	b	− 8 (− 15%)	− 1 Gt (− 16%)	− 5 Gt (− 19%)	− 9 Gt (− 15%)	− 13 Gt (− 16%)
	c	− 9 Gt (− 18%)	− 1 Gt (− 16%)	+ 5 Gt (+ 20%)	− 11 Gt (− 18%)	− 15 Gt (− 19%)
	d	− 25 Gt (− 48%)	+ 1 Gt (+ 11%)	+ 6 Gt (+ 21%)	− 24 Gt (− 40%)	− 19 Gt (− 25%)
	e	− 31 Gt (− 61%)	+ 3 Gt (+ 39%)	+ 13 Gt (+ 50%)	− 28 Gt (− 47%)	− 18 Gt (− 23%)
	f	− 13 Gt (− 26%)	− 1 Gt (− 14%)	− 4 Gt (− 16%)	− 14 Gt (− 24%)	− 17 Gt (− 22%)
	g	− 19 Gt (− 36%)	− 1 Gt (− 11%)	− 3 Gt (− 11%)	− 20 Gt (− 23%)	− 21 Gt (− 28%)
	h	− 30 Gt (− 59%)	+ 1 Gt (+ 12%)	+ 4 Gt (+ 14%)	− 29 Gt (− 49%)	− 27 Gt (− 35%)
	i	− 32 Gt (− 63%)	+ 1 Gt (+ 11%)	+ 4 Gt (+ 14%)	− 31 Gt (− 52%)	− 29 Gt (− 37%)
	j	− 36 Gt (− 71%)	+ 20 Gt (+ 236%)	+ 77 Gt (+ 292%)	− 16 Gt (− 28%)	+ 40 Gt (+ 52%)

Values from 1995 to 2014 are estimates based on historical data, while the model simulation starts in 2015 (indicated by the dashed vertical line). 2014 values for total heat demand and emissions are represented as horizontal dashed lines. In plots for scenarios b–j, solid curves indicate the baseline demand trend (from scenario a). Percentage values refer to changes in demand and total annual CO₂ emissions by 2050, relative to 2014. Values in brackets refer to the respective changes in direct CO₂ emissions.

In our baseline projection under current policies and diffusion trends (scenario a), annual direct CO₂ would peak by 2030, before returning to their 2014 level by 2050. Given the projected increase in heat demand of + 46%, this suggests a decrease in the direct emission intensity by around 30%. Importantly, these changes in our baseline do not result from any exogenous efficiency change, but from the endogenous continuation of current technology diffusion trends: the model projects a continuously increasing market share of heat pumps, solar thermal heating and modern biomass systems. Their combined share would grow from 9 p.p. (percentage points) of heat production in 2014 to 30 p.p. in 2050. An uptake of more efficient gas heating systems and a gradual replacement of coal and oil based systems leads to further emission reductions. Still, fossil fuel systems are projected to supply a more or less constant amount of heat and keep a combined market share of 40 p.p. by 2050, down from 50 p.p. in 2014. Total emissions are projected to decrease by − 18% by 2050, given that the power sector is decarbonised.

In scenario b, improved insulation of houses would reduce overall heat demand in 2050 by 20% (relative to baseline scenario a), indicating the untapped potential of increased building efficiency. In combination with a continued diffusion of renewables, this could lead to a 31% reduction of total emission levels, although absolute heat demand would still be 18% larger than in 2014. Compared to baseline, the increased thermal efficiency of new houses would reduce cumulative total CO₂ emissions by 9 GtCO₂ between 2020 and 2050.

In scenario c, we assume that all houses converge to an average heating intensity of 45 kJ/m²/HDD until 2050, which implies that a large fraction of existing buildings would be retrofitted with improved insulation. As can be seen in Fig. 2, this would foremost lead to additional demand reductions in North America, Europe and the Former Soviet Union (by 15–20% in 2050, relative to demand in SSP2–1.9). Compared to scenario b, total global heat demand by 2050 would be 9% lower than in 2014, leading to projected additional reductions of direct emission of a similar magnitude.

Other than for scenarios b and c, the resulting impacts of technology policies in scenarios d–j are not imposed by assumption (e.g. by assuming stricter building codes), but are subject to the simulated decision-making by households. The resulting technology transitions therefore depend on the behavioural characteristics of simulated decisions.

In scenario d, an (increasing) carbon tax of 50–200 €/tCO₂ is introduced in 2020. Due to bounded rationality and limited information on part of households, the projected changes in technology uptake would only unfold very gradually, showing considerable inertia: households would still install new oil systems until 2035 and new gas systems even up to 2050. As households learn about the new technologies, and industry capacities expand, renewables would increasingly grow in market shares. Compared to scenario c, annual heat generation in 2050 by heat pumps would be 90% larger, solar thermal by 18% and modern biomass by 50% (reaching a combined market share of 45 p.p. by 2050). The resulting decrease in annual total emissions would be 77% in 2050.

In scenario e, an (increasing) carbon tax of 100–400 €/tCO₂ is projected to bring down direct emissions by 95% and total emissions by 84%. Relative to the lower carbon price in scenario d, the 2050 market shares of heat pumps and modern biomass would increase by + 13 and + 11%, while shares of solar remain virtually unaffected. This indicates a decreasing marginal impact of carbon taxes on household decisions: although moderate tax levels can be sufficient for slowly steering household choices for regular replacements and new installations away from fossil fuel technologies, slow turnover rates limit the resulting pace of change in the technology composition. Furthermore, households tend to discount future fuel savings which can be achieved by adopting highly efficient, but capital-intensive modern renewables. Such technologies are disadvantaged by their higher upfront costs, which have a more than proportional impact on households’ decision-making. Instead, the carbon price would induce a shift towards (less efficient) direct electric heating (which would grow by 30%, relative to scenario d), resulting in indirect emission increases.

Subsidy schemes are simulated in scenarios f and g. The projected decrease in annual total CO₂ emissions by 2050 is 49% for a 25% subsidy and 62% for a 50% subsidy. Results suggest a clear shift of household choices towards more capital-intensive and efficient technologies, in comparison to the carbon tax: solar thermal and ground-source heat pumps show the largest increases in uptake (up to + 100 and + 200% relative to scenario c, respectively). Accordingly, electricity use for heating is around 50% lower than in the carbon tax scenarios, making the technology portfolio much more robust against potential indirect emission increases in the power sector. Still, results suggest that on their own, even large subsidies could not motivate many households to replace functioning systems prematurely. Even if ‘scrapping’ would look beneficial from an outside perspective, households tend to apply strict behavioural payback criteria for such decisions, which makes ‘scrapping’ unattractive from their subjective perspectives (see section ‘Premature replacements’).

In scenario h, the 50% subsidy on renewables is combined with the 50–200 €/tCO₂ carbon tax. From a behavioural perspective, the policy mix impacts households’ decision-making like ‘carrot and stick’: the tax enacts a steadily increasing economic pressure on households, strong enough so that a growing proportion of them may eventually want to reconsider their preference for fossil fuel technologies. In parallel, the subsidy has an over-proportional impact on costs as they are perceived by households, in particular in case of premature replacements (see Fig. 6), thereby benefiting modern renewables. According to the model projections, the policy mix could thus induce a wave of premature replacements. As a result, annual total emissions by 2050 could be reduced by 85%.

While the policy mix of scenario h is projected to incentivise a decarbonisation pathway in most world regions, results suggest that the policies would be relatively ineffective in the Middle East and Russia, where two-third of remaining emissions would occur by 2050. In both regions, the diffusion of renewables is not just constrained by comparably low fossil fuel prices but also by the practical absence of such technologies in the present technology mix, which implies limited local knowledge and experience. Scenario i therefore adds ‘kick start’ policies for driving the initial market for renewables in Russia and OPEC states, e.g. in form of procurement schemes (see section ‘Scenario definition’). Once households and local industry learn about the new technologies, a diffusion process is nucleated, and the financial incentives can have a much larger impact. Overall, the policy mix is projected to reduce total emissions by 90% (direct emissions by 95%), the largest total reduction in all scenarios.

Results of scenarios h and i imply that mixing policies enables to impose a lower carbon price and reduce costs to households (see section ‘Cost-effectiveness of policies’), in contrast to common model assumptions in which all policies are assumed to have a ‘carbon price equivalent’. In a diffusion model, policy interacts, and the behavioural details of the policy mix (and how it impacts household decisions) matters. Compared to a carbon price on its own (scenario e), our results suggest that the transition to renewables could take place with more efficient (albeit more capital-intensive) technologies: although leading to similar direct emission reductions, the carbon tax on its own would lead to much higher electricity use, leading to larger expenses on electricity and indirect emission increases in the power sector.

In all scenarios, an increased electrification of residential heating has direct implications for the power sector. Annual electricity demand for residential heating in 2014 was around 1 PWh/year (or 4% of global electricity demand), causing indirect emissions of 0.5 GtCO₂/year. In our baseline projection, it would increase to 2 PWh/year in 2050. Without decarbonisation of the power sector, indirect emission could then reach 1.1 GtCO₂/year. Net reductions in cumulative 2015–2050 CO₂ emissions thus strongly depend on a parallel decarbonisation of electricity generation (see Table 1). Indirect emission increases cancel out 5–20% of direct emission savings when assuming a rapid power sector decarbonisation, but up to 55% when the sector continues on its current trajectory. Net savings are much more sensitive to induced power sector emissions in scenarios which only rely on a carbon tax, due to their relatively higher levels of electricity demand. Despite this, residential emission reductions in scenarios c–i would always exceed potential emission increases in the power sector.

In scenario j, we explore the extreme case of complete electrification. In addition to the 100–400 €/tCO₂ carbon tax from scenario e, we assume that electricity use for heating is subsidised by 0.05 €/kWh and the purchase of all electricity-based systems by 30%. Because electric heaters are a readily available and well-known technology in most world regions, also being clean and convenient in use, our model suggests a relatively rapid uptake once costs are favourable: direct electric heating alone would gain a 75% market share by 2050, reducing on-site emissions by as much as 99%. However, resulting electricity demand would reach 9 PWh/year, requiring 2,000–2,400 GW of additional generation capacity (almost half of the currently installed global capacity). Indirect emissions would cancel out 80% of direct CO₂ reductions even under power sector decarbonisation and could reach up to 6 GtCO₂/year otherwise. This makes a direct electrification of heating an overall rather ineffective (or even counterproductive) mitigation strategy, particularly given the availability of much more efficient alternatives.

Table 2 presents the sensitivity of our scenario results with respect to key parameters (for the sensitivity with respect to ‘scrapping’ assumptions, see section ‘Dynamics in an exemplary decarbonisation scenario’). It becomes evident that results are relatively robust to changes in cost parameters: under alternative assumptions on fuel price trends, learning rates and discount rates, cumulative direct CO₂ emissions do not change by more than 7% in any scenario. The largest emission increases can be seen for changes in ‘intangible’ cost components: if they are reduced by 50%, cumulative emissions are up to 12% higher (even 25% in case of the complete electrification scenario, because electric heating would become less attractive). This is partly due to the fact that large ‘intangible’ costs are attributed to coal, the reduction of which would lead to the uptake of emission-intensive coal heating systems. Apart from cost parameters, results are sensitive to the assumptions on technology lifetimes: in case of shorter lifetimes, technological change can take place more quickly, reducing cumulative emissions. The reverse effect can be observed for longer lifetimes, albeit being less pronounced (as more households would be projected to replace their heating systems prematurely, which would partly offset the effect of longer technological lifetimes).

Table 2

Sensitivity of cumulative 2015–2050 direct CO₂ emissions in residential heating, with regard to: (I) future energy price developments (relative to scenarios with constant future energy prices), assuming: (a) a linear increase in all residential fuel prices by + 1% per year (2018–2050), (b) a linear decrease in all residential fuel prices by − 1% per year (2018–2050); (II) learning rate for heating systems (50% lower than default assumption); (III) discount rate (50% higher than default assumption); (IV) ‘intangible’ component of generalised heating cost (50% lower than default estimates); and (IV) technology lifetimes (− 50 and + 50%)

% deviation of cumulative 2015–2050 direct CO₂ emissions, relative to default parameters
	Increasing fuel prices	Decreasing fuel prices	Learning rates	Discount rate	Intangibles	Technology lifetimes
	(+ 1%p.a.)	(1%p.a.)	(− 50%)	(+ 50%)	(− 50%)	(− 50%)	(+ 50%)
a	− 4%	+ 5%	+ 3%	+ 3%	+ 7%	− 13%	+ 4%
b	− 3%	+ 4%	+ 2%	+ 2%	+ 7%	− 12%	+ 4%
c	− 3%	+ 4%	+ 2%	+ 2%	+ 7%	− 12%	+ 4%
d	0%	+ 1%	+ 4%	+ 2%	+ 10%	− 20%	+ 8%
e	+ 2%	− 1%	+ 4%	+ 1%	+ 12%	− 20%	+ 9%
f	− 4%	+ 6%	+ 3%	+ 2%	+ 8%	− 16%	+ 5%
g	− 3%	+ 7%	+ 5%	+ 1%	+ 10%	− 17%	+ 8%
h	0%	0%	+ 5%	+ 1%	+ 10%	− 18%	+ 9%
i	− 1%	+ 1%	+ 6%	+ 1%	+ 9%	− 20%	+ 9%
j	+ 3%	− 2%	+ 2%	+ 1%	+ 25%	− 19%	+ 35%

Cost-effectiveness of policies

From a public policy perspective, the decarbonisation of heating could not only be beneficial for climate change mitigation but potentially also enable a more efficient provision of heat in monetary terms. The cumulative projected costs and savings from the induced technology transitions (in scenarios d–j) are presented in Table 3 and illustrated by Fig. 4, relative to scenario c (with improved insulation, but without technology policies). Figure 5 exemplarily shows the underlying changes over time per world region in case of four scenarios.

Table 3

Cumulative changes in global expenses on residential heating (billion Euro, bn€), for policy scenarios d–j (aiming at uptake of low-carbon technologies), relative to scenario c (improved insulation and retrofitting, without technology policies). Monetary values are shown in constant 2015-Euros (undiscounted). Changes in expenses on heating systems per tCO₂ refer to net reductions in CO₂ emissions (direct plus indirect from electricity use). Note that estimates of avoided social costs of CO₂ emissions are not included in the calculations

	Scenario	Expenses on heating systems		Expenses on energy for heating	Total expenses on heating	Policy revenue (Tax minus subsidy)
	Scenario	bn€(‘15)	€(‘15)/tCO₂	bn€(‘15)	bn€(‘15)	bn€(‘15)
	c	4.600	–	16.030	20.630	–
Diff. to (c), in bn€(‘15)	d	+ 460(+ 10%)	36	− 1.010(− 6%)	− 550(− 3%)	2.750
	e	+ 770(+ 17%)	44	− 830(− 5%)	− 60(− 0%)	3.730
	f	+ 460(+ 10%)	121	− 1.160(− 7%)	− 700(− 3%)	− 400
	g	+ 1.170(+ 25%)	132	− 2.600(− 16%)	− 1.430(− 7%)	− 1.220
	h	+ 1.540(+ 33%)	82	− 3.190(− 20%)	− 1.650(− 8%)	590
	i	+ 1.650(+ 36%)	80	− 3.400(− 21%)	− 1.750(− 8%)	240
	j	+ 1.640(+ 36%)	284	+ 3.080(+ 19%)	+ 4.720(+ 23%)	− 10.800

As illustrated by Fig. 4, our results suggest that a carbon tax would induce emission reductions at relatively lower additional investments per t/CO₂, compared to policy mixes which involve subsidies. However, high carbon taxes show a decreasing marginal impact on total emissions and could therefore only reduce them up to a certain extent (− 84% in our simulations). While a carbon tax on its own would set the stage for making renewables more cost-competitive, larger emission reductions could be achieved by richer policy mixes, which are projected to trigger more fuel-efficient pathways of technological change (see Appendix Fig. 9). Albeit being more capital-intensive (reflected in higher additional investments per t/CO₂), such policy mixes could also lead to larger fuel savings (reflected in higher savings in energy expenses per t/CO₂).

In all scenarios, cumulative expenses on heating systems are projected to increase between 10 and 36%. Subsidies would lead to relatively larger increases (compared to carbon taxes) in terms of €/tCO2 net reduction, as they incentivise the purchase of more capital-intensive technologies. At the same time, the new technologies are much more energy-efficient, thus enabling substantial reductions in energy expenses for heating, which range between 5 and 21%. As for expenses on heating systems, policy mixes which involve subsidies are also projected to result in larger energy savings, as they lead to the adoption of more energy-efficient technology portfolios.

In all scenarios, projected savings from energy expenses exceed the additional costs for the purchase of new heating systems (assuming constant energy prices), leading to reductions in overall expenses on heating by up to 8%. The notable exemption is scenario j, in case of which the transition to (relatively inefficient) electric resistance heating would increase overall expenses by more than 20%. Projected net savings are largest for policy mixes which involve both taxes and subsidies (h and i). While they show the largest increases in expenses on heating systems, those would also enable the largest energy savings and emission reductions.

Households, however, do not directly face the changes in net costs. They also need to pay for the carbon taxes, while potentially benefiting from purchase subsidies. When taxes are used as the only policy instrument, tax payments would by far exceed the achievable savings in real costs. Net benefits for households would then depend on the way in which tax revenues are redistributed. In case of policy mixes, part of the tax revenues would be recycled into purchase subsidies. Savings in real costs would then exceed the net burden from policies to households (tax payments minus subsidy payments) by a factor of 3–7.

Importantly, costs and savings would not occur simultaneously (see Fig. 5). In most world regions, additional expenses on heating systems would peak around 2030. Meanwhile, resulting changes in energy expenses only gradually increase over time, not reaching their full extent before 2050. In most world regions, substantial net savings are thus not projected before 2040. This type of temporal trade-off implies that while overall net savings may be large from a public policy perspective, specific technology choices may still remain unattractive from the perspective of individual households (which tend to discount future savings), if they are not incentivised by policies.

Furthermore, costs and savings are not equally distributed between world regions. While most regions show a similar profile of relative changes in expenses over time, some regions are projected to realise much larger net savings (e.g. in China), while others could face net cost increases for longer periods of time (e.g. in North America). The largest relative cost increases could occur in Russia and North Africa/Middle East, where current fossil fuel prices are considerably lower than in other world regions. The addition of ‘kick start’ policies for those regions, however, is projected to reduce those cost increases considerably, as it would incentivise the diffusion of more efficient alternative technologies.

Dynamics in an exemplary decarbonisation scenario

We here analyse the dynamics of decarbonising residential heating, focusing on scenario i. The cost dynamics underlying the technology transition are illustrated in Fig. 6 and the resulting impacts on technological change in Fig. 7, under different assumption regarding household behaviour.

The left panel of Fig. 6 shows global averages for the generalised cost per technology as seen by households, including policies and ‘intangibles’. Without new policies and at current prices, heat pumps are not yet competitive with gas heating, but on par with oil. Solar thermal is already competitive on average, which mainly reflects low costs in China, where 66% of the global capacity was installed in 2014. Biomass is competitive with fossil fuels in most world regions, but uptake is often less influenced by prices than by households’ preferences, which tend to regard biomass as less convenient. When introducing new policies in 2020, the carbon tax increases the cost of fossil fuel heating, while subsidies decrease the cost of renewables, making them competitive with gas. The gradual phase-out of subsidies after 2030 is largely compensated by learning-induced decreases in investment costs, keeping levelised costs of renewables relatively stable until 2050. Induced by large capacity increases, investment costs for solar thermal and ground-source heat pumps are projected to decrease by − 20 and − 45% until 2030 (relative to 2014), respectively, with further reductions until 2050 (overall − 30 and − 66%, respectively). For comparison: the IEA (2016b) expects the costs of solar thermal to decrease by around − 40% until 2030.

The right panel shows the marginal running costs of fossil fuel heating, compared to full payback costs for renewable technologies (assuming a payback period of 3 years). Choice experiments on the behavioural decision-making of households indicate that as long as the former do not exceed the latter, households would not consider a premature replacement, even if it would be highly profitable from an outside perspective (Newell and Siikamäki 2015; Olsthoorn et al. 2017). The combined effect of the 50–200 €/tCO₂ fuel and 50% subsidy on renewables is just large enough (despite translating into much larger differences in levelised costs): after 2020, the fuel savings from replacing an oil or gas system by renewables increasingly exceeds the necessary investment in less than 3 years, potentially incentivizing the scrapping of fossil fuel capacities before they reach the end of their rated technological lifetime.

The resulting dynamics in technological change can be seen in Fig. 7, which shows projections for the total global heating capacity, capacity built per year and capacity scrapped per year, under different behavioural assumptions. Under the modelled mean payback threshold of 3 years (middle panels), scrapping happens rarely before 2020: less than 20 GW (0.3%) of the global capacity would be replaced prematurely each year, while total capacity additions are around 400 GW/year (6.6%). After 2020, scrapping would gradually increase, peaking at 115 GW/year (around 1.8%) in the 2030s. While small on an annual basis, the model suggests that households would scrap a total capacity of 2.700 GW from 2020 to 2050, which is around 45% of the installed capacity in 2020. The induced dynamics are self-reinforcing, allowing a faster growth of households’ experience and industry know-how regarding renewable heating technologies, and eventually an almost complete phase-out of fossil fuel systems by 2050.

The importance of household behaviour and related uncertainty becomes evident in comparison with the upper and lower panels of Fig. 7, which depict the same dynamics for hypothetical mean payback thresholds of 15 years and 1 year. Applying a threshold of 15 years is equivalent to a discount rate of 3% (given a technical life expectancy of 20 years), implying the optimistic assumption that household decisions take into account potential future savings to almost full extent. If households were indeed acting in that way, the model suggests that they should scrap around 130 GW/year (2.4%) even before policies get introduced in 2020 and up to 200 GW/year (3.6%) immediately afterwards. Households would also favour more capital-intensive technologies, as evidenced by the rapid uptake of solar thermal and ground-source heat pumps. In a world of such forward-looking households, heating could be largely decarbonised by 2035, around 15 years earlier than in scenario i.

The opposite result is projected if households were to apply an average payback threshold of 1 year. In this case, they would only replace their heating system once expected savings exceed the upfront cost within 1 year. Scrapping would then be virtually non-existent before 2020 (8 GW/year) and not exceed 50 GW/year (0.8%) in the 2030s. While renewables could still grow to service additional demand (such as in China), the decarbonisation of the existing building stock would largely depend on regular replacements. Given average technical lifetime of 20 years and the implemented model assumptions on diffusion dynamics (in which growth is correlated to current market shares), our projections suggest that a complete transition is then not achievable until 2050, at least not under the simulated policies: fossil fuel capacities in 2050 would remain at 40% of their current level.

Discussion and conclusion

Our results suggest that an almost complete decarbonisation of residential heating is possible until 2050, based on a combination of improved building insulation and existing technologies, but unlikely to happen without stringent policy instruments. We find that a carbon tax on its own could drive an initial decarbonisation (up to − 84% by 2050), but shows a decreasing marginal impact on total emission reductions. A more ambitious decarbonisation (up to − 90%) at lower tax rates can be achieved when the carbon tax is supplemented by subsidies and procurement policies for renewables. Such policy mixes are projected to be more effective for driving the market of low-carbon technologies, resulting in lower cumulative net emissions and reduced cost burdens for households, compared to a carbon tax on its own. From a societal perspective, emission reductions may be achieved at low or even negative cost: initially higher capital expenses could lead to permanently decreased energy expenses in most world regions.

The simulated technology transitions in residential heating would need decades rather than years, in parts simply due to long average lifetimes of heating equipment. Given such time-scales, our model projections suggest that a complete decarbonisation until 2050 does not only require an immediate ramp-up of low-carbon investments but also that households replace (or ‘scrap’) a substantial share of inefficient heating systems prematurely. Therefore, the simulated effectiveness of policies inevitably depends on behavioural assumptions on ‘scrapping’ decisions.

Overall, there remains a considerable degree of uncertainty regarding behaviour, data and the future development of technology characteristics, under which the true long-term effect of any policy is hard to estimate a priori. Representing all relevant behavioural factors in a quantitative global energy model may remain an unachievable benchmark, given that no model can ever be more than a stylised representation of reality. We thus chose a midway compromise, integrating in a stylised form available knowledge on technology diffusion and household decision-making into a bottom-up simulation model of technology choice. While it remains limited in its degree of realism, we argue that it provides a clear improvement on incumbent optimisation models, shedding light on important diffusion dynamics and behavioural uncertainties.

Our results show that such uncertainties are particularly relevant in the context of limiting global warming to 1.5 °C, which requires policies aiming at rapid deep decarbonisation, and are outside of what has so far been implemented in most parts of the world. Due to our inclusion of behavioural features, however, our projections are potentially more valuable to policy-makers for carrying out impact assessments of possible sets of policies, in comparison to standard optimisation models that assume perfect information and rationality. Due to their use of unrealistic behavioural assumptions, the latter could potentially mislead policy-makers towards excessively simplistic policy strategies for incentivising the decarbonisation of households.

Other aspects of household decision-making are likely relevant, but still remain unspecified in our modelling—such as split incentives (e.g. in case of rented property) or a limited access to finance (which is one possible reason explaining low required payback times). The value of ‘intangibles’, which we estimate from historical diffusion trends, is not necessarily constant over decades, but may change over time. Some behavioural uncertainties remain impossible to simulate, so that our results may still be considered as optimistic.

While our modelling achieves the target with our set of assumed behavioural features, it can only indicate the potential of behaviourally-oriented policies. Much remains unknown on how to specifically design and implement such policies, which must take into account as much additional behavioural knowledge as possible, and can benefit substantially from psychological and sociological research. While the evidence base remains relatively thin, there is little time to spare, and therefore, further research in the direction of behavioural science and modelling will need to be carried out in conjunction to the introduction of policies.

Acknowledgements

FTT:Heat originates from a project commissioned by the European Commission, Directorate-General for Energy (Contract No. ENER/A4/2015-436/SER/S12.716128) (more details are available at the link http://ec.europa.eu/energy/en/data-analysis/energy-modelling). The authors thank Lorena van Duuren and Pim Vercoulen for the research assistance, Aileen Lam for the data collection on Asia, Richard Lewney for coordinating the project from Cambridge Econometrics, Mark Huijbregts for the feedback and valuable discussions, Joan Canton from the European Commission for the guidance and the other DG ENER staff for the helpful feedback and additional guidance. We gratefully thank the anonymous referees who helped us improve this manuscript significantly.

Compliance with ethical standards

Conflict of interest

The authors declare that they have no conflict of interest.

Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Vorheriger Artikel Mobility, food and housing: responsibility, individual consumption and demand-side policies in European deep decarbonisation pathways

Nächster Artikel Will policies to promote energy efficiency help or hinder achieving a 1.5 °C climate target?

Electronic supplementary material

ESM 1 (XLSX 363 kb)

Appendix

Table 4

Grouping of the 59 E3ME regions (right) into 11 major world regions (left) (aggregation is only for presentation of results, FTT:Heat simulates all 59 regions individually)

Western Europe	Belgium, Denmark, Germany, Greece, Spain, France, Ireland, Italy, Luxembourg, Netherlands, Austria, Portugal, Finland, Sweden, UK, Cyprus, Malta, Norway, Switzerland, Iceland, Turkey
Central and Eastern Europe	Czech Republic, Estonia, Latvia, Lithuania, Hungary, Poland, Slovenia, Slovakia, Bulgaria, Romania, Croatia, Macedonia
North America	USA, Canada
Latin America	Mexico, Brazil, Argentina, Colombia, Rest of Latin America
Former Soviet Union	Russia, Belarus, Ukraine
China	China
South and Pacific Asia	Indonesia, the rest of ASEAN, India, Korea, Taiwan
Oceania (Pacific OECD)	Australia, New Zealand, Japan
North Africa and Middle East	Saudi Arabia, OPEC excl. Venezuela, Africa OPEC
Sub-Saharan Africa	Nigeria, South Africa, the rest of Africa
The rest of world	The rest of world (all other countries)

Estimation of intangible cost components

The technology- and region-specific empirical parameter γ_i is estimated in a two-step calibration procedure (shown in Appendix Fig. 10): first, we run the model based on the cost estimates of LCOH_i only, with γ_i = 0 for all technologies. For each region, we then compare the growth of technologies as projected by the model with the diffusion trend as observable in the historic data, using a graphical interface. If there are deviations, we iteratively adjust the values of γ_i (upwards or downwards), until the projected diffusion at the start of the simulation is consistent with the empirical trends. The estimated values of ‘intangibles’ are assumed to be constant over the simulation period, since we have no possibility to estimate future preferences.

On average, we find that oil, gas (incl. LPG) and district heating are slightly more attractive to households than suggested by the pure costs, leading to values of γ_i in the range of − 10 to − 15%, relative to the pure LCOH_i. For electric resistance heating, the average γ_i is equivalent to − 30% of its LCOH_i. The opposite holds for coal and biomass heating, for which typical γ_i values are between + 40 and + 80%. For solar thermal and heat pumps, values differ by region, usually between − 20 and + 20%.

Detailed technology data

Table 5

Model assumptions for residential heating technologies. Costs refer to mean values. (Data sources: Fleiter et al. (2016), IEA/ETSAP (2012), Danish Energy Agency (2013), EHPA (2016))

	Upfront cost (€/kW_th)	O&M cost (€/kW_th pa)	Efficiency (kWh_th/kWh)	Learning rate (%)
Oil	471	19	0.75	–
Oil condensing	512	20	0.86	− 10%
Gas	391	8	0.75	–
Gas condensing	434	9	0.9	− 10%
Biomass stove	440	0.1	0.1–0.7	–
Biomass boiler	523	2	0.85	− 10%
Coal	247	5	0.75	–
District heating	265	16	0.98	–
Direct electric	538	0.5	1.00	–
HP-ground source	1400	14	3.50	− 30%
HP-air/water	750	15	2.50–2.70	− 30%
HP-air/air	510	51	2.50–2.70	− 30%
Solar thermal	773	8	–	− 10%

Conversion efficiencies refer to the ratio of thermal energy ‘leaving’ the heating system, relative to the necessary energy input, covering both space and water heating. In the case of traditional biomass, lower conversion efficiencies (10–50%) are assumed in developing countries (IEA 2014). For heat pumps, efficiency values are defined as their seasonal performance factor (the annual average ratio of delivered heat to electricity input), which differs by climate region. For solar thermal, local productivities are calculated from data by the IEA Solar Heat Programme (Mauthner et al. 2016), which we integrate into the model as region-specific capacity factors (i.e. units of heat produced per unit of capacity installed). The average technical life expectancy is set to 20 years for all technologies, based on literature estimates (the actual lifetime may be shorter if households decide to replace a system earlier for economic reasons) (Danish Energy Agency 2016; IEA/ETSAP 2012).

Table 6

Model estimates for levelised cost of heating (LCOH), generalised cost of heating (GCOH), estimated values of intangible cost components and standard deviation of LCOH. All numbers refer to mean values, calculated as the average of all 59 modelled world regions (weighted by their heat demand)

	LCOH	GCOH	Estimated values of intangibles		Standard deviation of LCOH
	€-Cent/kWh_th	€-Cent/kWh_th	€-Cent/kWh_th	%LCOH	€-Cent/kWh_th	%LCOH
Oil	11.1	9.7	− 1.3	− 12%	0.02	17%
Oil condensing	10.2	9.0	− 1.3	− 13%	0.02	17%
Gas	9.3	8.0	− 1.2	− 13%	0.02	17%
Gas condensing	8.2	6.6	− 1.6	− 20%	0.01	18%
Biomass stove	5.8	5.1	− 0.7	− 11%	0.02	29%
Biomass boiler	4.3	5.9	1.6	37%	0.01	30%
Coal	3.0	5.5	2.5	84%	0.01	27%
District heating	7.2	6.2	− 1.1	− 15%	0.01	16%
Direct electric	11.8	8.6	− 3.2	− 27%	0.02	14%
HP-ground	9.3	8.7	− 0.7	− 7%	0.02	25%
HP-air/water	8.7	8.0	− 0.7	− 8%	0.02	21%
HP-air/air	8.8	8.4	− 0.4	− 5%	0.02	19%
Solar thermal	10.8	10.0	− 0.8	− 8%	0.04	33%

Regional technology pathways in scenario i

Appendix Fig. 11 summarises the simulated future development of residential heating systems in five major world regions, together accounting for 80% of heat demand and direct heating CO₂ emissions in 2014. Technology composition and emissions by region are shown for a projection under improved levels of building insulation (scenario c) on the left and under additional policies for technological decarbonisation of heating (scenario i) on the right.

In Western Europe and North America, heating is currently dominated by gas. Under baseline conditions, their technology composition would stay relatively constant, while the ongoing diffusion of more efficient gas heating systems and a limited uptake of renewables implies a continued but slow decrease of emissions. Under policies in scenario h, fossil fuel heating and direct electric heating in both regions would be substituted by a mix of heat pumps and solar thermal, with only limited diffusion of modern biomass.

In Central and Eastern Europe, large shares of the heating demand are currently serviced by district heat networks, biomass and gas. Most direct emissions, however, originate in a relatively large share of coal heating, compared to other world regions. Modern renewables are mostly absent under current technology diffusion trends. Under decarbonisation policies, our model suggests that fossil fuels would be substituted by a mix of biomass and heat pumps, while the projected uptake of solar thermal remains low.

In China, fossil fuels still play a smaller role in heating. Historically, most emissions result from coal. Oil and gas are on the rise, however, and would continue their ongoing growth under baseline conditions. At the same time, a widespread uptake of solar thermal systems and heat pumps is taking place, so that baseline emissions are projected to peak around 2030 and decrease afterwards. With additional policies, the shift to renewables would be accelerated, with solar supplying the equivalent of two-thirds of the water heating demand by 2050. Importantly, China is also the region with largest projected demand increases until 2050, driven by continuously rising incomes (and coming from historically very low values of heating intensity).

In the Former Soviet Union, 60% of heat is currently provided by district heating systems, the remaining fraction by gas and oil. No use of renewables is reported, limiting the potential for a fast technology transition. Therefore, only little change would take place in the baseline, with slowly rising emission levels until 2050. With decarbonisation policies, only the introduction of ‘kick start’ schemes would eventually lead to a limited uptake of renewables. Most emissions occur not on site, but in centralised heat plants. A parallel decarbonisation would thus need to take place in the country’s district heating systems, which are not explicitly modelled here (the same holds for central heating in other world regions).

Cost is potentially negative when mitigation options do not only reduce emissions, but also the underlying energy use, which may lead to savings on energy expenses in excess of the necessary investment.

Woody biomass can be considered as emission neutral assuming that plants grow to compensate the carbon emitted as they are combusted, so that the stock of forests (and carbon therein) does not decline as a result of biomass combustion. For discussions, see Zanchi et al. (2012) and Lamers and Junginger (2013).

Under the incorrect assumption that the sum of individual cost-optimisers corresponds to a cost-optimising social planner, optimisation is often seen as descriptive; otherwise, optimisation is always normative (Mercure 2017).

The Passive House standard requires a maximum space heating energy demand of 15 kWh/m² (PHI 2018). This roughly translates to a maximum useful heating intensity of 20 kJ/m²/HDD. As we model aggregate heating intensity, reducing global heating intensity from 50 to 200 to 45 kJ/m²/HDD over a 30-year period is very ambitious and implies a large portion of households adopting passive house properties.

Ideally, we would have similar (and recent) empirical studies for all world regions. Unfortunately, those are not available. In their absence, some value needs to be chosen as a discount rate, so using results from the cited study on Canada is in our opinion an imperfect, but feasible solution.

We assume homogenous age distributions because we do not have data over the age structure of heating systems worldwide. The assumption implies that if a fleet of heating systems of a particular technology has been widely adopted in a country in a very short time, it would mean that they would need replacement in a relatively restricted range of years, which would break our assumption. It does not imply, however, that new innovative systems could be replaced instantaneously; these would nevertheless wait until the end of their average expected lifetime to be replaced (unless households would replace prematurely). The constraint of not considering the exact age distribution is furthermore relaxed by the fact that systems have a probability of end of life that is distributed over time (not all systems of the same type end up with the exact same lifetime).

Note that if for any technology i, F_ij < 50% for every other technology j, then the shares of i are going to decline over time. However, it does not mean that nobody is buying technology i. It simply means that more people are buying alternative technologies. As a result, the population of technology i declines gradually.

The specific carbon tax is only applied to the residential sector, and not assumed to be linked to other sectors, such as the power sector, which is subject to a separate set of policies.

https://www.gov.uk/government/publications/vat-notice-70119-fuel-and-power/vat-notice-70119-fuel-and-power.

Abrahamse, W., & Steg, L. (2009). How do socio-demographic and psychological factors relate to households’ direct and indirect energy use and savings? Journal of Economic Psychology, 30, 711–720. https://doi.org/10.1016/j.joep.2009.05.006.CrossRef

Abrahamse, W., & Steg, L. (2013). Social influence approaches to encourage resource conservation: a meta-analysis. Global Environmental Change, 23, 1773–1785. https://doi.org/10.1016/j.gloenvcha.2013.07.029.CrossRef

Abrahamse, W., Steg, L., Vlek, C., & Rothengatter, T. (2005). A review of intervention studies aimed at household energy conservation. Journal of Environmental Psychology, 25, 273–291. https://doi.org/10.1016/j.jenvp.2005.08.002.CrossRef

Achtnicht, M., & Madlener, R. (2014). Factors influencing German house owners’ preferences on energy retrofits. Energy Policy, 68, 254–263.CrossRef

Allcott, H., Greenstone, M. (2012). Is there an energy efficiency gap (No. No. w17766). Cambridge, MA.

Allcott, H., & Mullainathan, S. (2010). Behavioral science and energy policy. Science (80-.)., 327, 1204–1205.CrossRef

Arthur, W. B. (1989). Competing technologies, increasing returns, and lock-in by historical events. The Econometrics Journal, 99, 116–131.

Bager, S., & Mundaca, L. (2017). Making “smart meters” smarter? Insights from a behavioural economics pilot field experiment in Copenhagen, Denmark. Energy Res. Soc. Sci., 28, 68–76.CrossRef

Cambridge Econometrics. (2014). E3ME Manual, Version 6.

Cayla, J. M., & Maïzi, N. (2015). Integrating household behavior and heterogeneity into the TIMES-Households model. Applied Energy, 139, 56–67. https://doi.org/10.1016/j.apenergy.2014.11.015.CrossRef

China Heat Pump Committee of China Energy Conservation Association. (2015). China Heat Pump Industry Development Report 2015.

Clarke, L.E., Jiang, K., Akimoto, K., Babiker, M., Blanford, G., Fisher-Vanden, K., Hourcade, J.-C., Krey, V., Kriegler, E., Löschel, A., McCollum, D., Paltsev, S., Rose, S., Shukla, P.R., Tavoni, M., van der Zwaan, B.C.C., van Vuuren, D.P., 2014. Assessing transformation pathways. Clim. Chang. 2014 Mitig. Clim. Chang. Contrib. Work. Gr. III to Fifth Assess. Rep. Intergov. Panel Clim. Chang. 413–510.

Clayton, S., Devine-Wright, P., Stern, P. C., Whitmarsh, L., Carrico, A., Steg, L., Swim, J., & Bonnes, M. (2015). Psychological research and global climate change. Nature Climate Change, 5, 640–646. https://doi.org/10.1038/nclimate2622.CrossRef

Connolly, D., Lund, H., Mathiesen, B. V., Werner, S., Müller, B., Persson, U., Boermans, T., Trier, D., Østergaard, P. A., & Nielsen, S. (2014). Heat roadmap Europe: combining district heating with heat savings to decarbonise the EU energy system. Energy Policy, 65, 475–489. https://doi.org/10.1016/j.enpol.2013.10.035.CrossRef

Connor, P., Bürger, V., Beurskens, L., Ericsson, K., & Egger, C. (2013). Devising renewable heat policy: overview of support options. Energy Policy, 59, 3–16. https://doi.org/10.1016/j.enpol.2012.09.052.CrossRef

Daioglou, V., van Ruijven, B. J., & van Vuuren, D. P. (2012). Model projections for household energy use in developing countries. Energy, 37, 601–615. https://doi.org/10.1016/J.ENERGY.2011.10.044.CrossRef

Danish Energy Agency. (2013). Technology data for energy plants—individual heating plants and energy transport. Danish Energy Agency.

Danish Energy Agency. (2016). Technology data for energy plants.

Dietz, T., Gardner, G. T., Gilligan, J., Stern, P. C., & Vandenbergh, M. P. (2009). Household actions can provide a behavioral wedge to rapidly reduce US carbon emissions. Proceedings of the National Academy of Sciences, 106, 18452–18456. https://doi.org/10.1073/pnas.0908738106.CrossRef

EIA. (2017). Residential Energy Consumption Survey Data 2015. U.S. Energy Information Administration (EIA).

Enerdata. (2017). ODYSSEE database [WWW Document]. URL www.odyssee-mure.eu

Eom, J., Clarke, L., Kim, S. H., Kyle, P., & Patel, P. (2012). China’s building energy demand: long-term implications from a detailed assessment. Energy, 46, 405–419. https://doi.org/10.1016/j.energy.2012.08.009.CrossRef

EurObserv’ER. (2017). EurObserv’ER [WWW Document]. URL https://www.eurobserv-er.org/

European Heat Pump Association (EHPA). (2016). Data on heat pump stock, capacities, usable energy production and system costs, 1990-2014 [WWW document]. http://www.ehpa.org

Fleiter, T., Steinbach, J., Ragwitz, M. (2016). Mapping and analyses of the current and future (2020-2030) heating/cooling fuel deployment (fossil/renewables). European Commission, Directorate-General for Energy.

Frederick, S., Loewenstein, G., & O’Donoghue, T. (2002). Time discounting and time preference: a critical review. Journal of Economic Literature, XL, 351–401.CrossRef

Frederiks, E. R., Stenner, K., & Hobman, E. V. (2015). Household energy use: applying behavioural economics to understand consumer decision-making and behaviour. Renewable and Sustainable Energy Reviews, 41, 1385–1394. https://doi.org/10.1016/j.rser.2014.09.026.CrossRef

Geels, F. W. (2002). Technological transitions as evolutionary reconfiguration processes: a multi-level perspective and a case-study. Research Policy, 31, 1257–1274.CrossRef

Geels, F. W., Sovacool, B. K., Schwanen, T., & Sorrell, S. (2017). Sociotechnical transitions for deep decarbonization. Science (80-. ), 357, 1242–1244. https://doi.org/10.1126/science.aao3760.CrossRef

Gillingham, K., & Palmer, K. (2014). Bridging the energy efficiency gap: policy insights from economic theory and empirical evidence. Review of Environmental Economics and Policy, 8, 18–38. https://doi.org/10.1093/reep/ret021.CrossRef

Giraudet, L.-G., Guivarch, C., & Quirion, P. (2012). Exploring the potential for energy conservation in French households through hybrid modeling. Energy Economics, 34, 426–445. https://doi.org/10.1016/j.eneco.2011.07.010.CrossRef

Grübler, A., Nakićenović, N., & Victor, D. G. (1999). Dynamics of energy technologies and global change. Energy Policy, 27, 247–280.CrossRef

Hausman, J. A. (1979). Individual discount rates and the purchase and utilization of energy-using durables. Bell Journal of Economics, 10, 33–54.CrossRef

Hecher, M., Hatzl, S., Knoeri, C., & Posch, A. (2017). The trigger matters: the decision-making process for heating systems in the residential building sector. Energy Policy, 102, 288–306. https://doi.org/10.1016/j.enpol.2016.12.004.CrossRef

Hofbauer, J., & Sigmund, K. (1998). Evolutionary games and population dynamics. Cambridge University Press.

IEA. (2013a). Transition to sustainable buildings—strategies and opportunities to 2050. International Energy Agency. https://doi.org/10.1787/9789264202955-en.

IEA. (2013b). Technology roadmap: energy efficent building envelopes 68. https://doi.org/10.1007/SpringerReference_7300.

IEA. (2014). Heating without global warming: market developments and policy considerations for renewable heat. International Energy Agency.

IEA. (2016a). Energy prices and taxes, volume 2016. International Energy Agency.

IEA. (2016b). World energy outlook 2016. IEA/OECD.

IEA. (2017). World energy statistics and balances (2017 edition). International Energy Agency.

IEA/ETSAP. (2012). Space heating and cooling—technology brief R02. International Energy Agency (IEA) Energy Technology Systems Analysis Program.

IEA/ETSAP and IRENA. (2013). Heat pumps technology brief. Energy Technology Systems Analysis Programme (ETSAP) of the International Energy Agency (IEA) and International Renewable Energy Agency (IRENA).

International Energy Agency. (2017). Tracking clean energy progress 2017.

Isaac, M., & van Vuuren, D. P. (2009). Modeling global residential sector energy demand for heating and air conditioning in the context of climate change. Energy Policy, 37, 507–521. https://doi.org/10.1016/j.enpol.2008.09.051.CrossRef

Jaccard, M., & Dennis, M. (2006). Estimating home energy decision parameters for a hybrid energy-economy policy model. Environmental Modeling and Assessment, 11, 91–100. https://doi.org/10.1007/s10666-005-9036-0.CrossRef

Jaffe, A. B., & Stavins, R. N. (1994). The energy-effincency gap: what does it mean? Energy Policy, 22, 804–810. https://doi.org/10.1016/0301-4215(94)90138-4.CrossRef

Japan Refrigeration and Air Conditioning Industry Association (JRAIA). (2017). Annual shipments of air conditioners & residential heat pump water heaters 1986–2016.

Jotzo, F., Burke, P. J., Wood, P. J., MacIntosh, A., & Stern, D. I. (2012). Decomposing the 2010 global carbon dioxide emissions rebound. Nature Climate Change, 2, 1–2. https://doi.org/10.1038/nclimate1450.CrossRef

Kahneman, D., & Tversky, A. (1979). Prospect theory: an analysis of decision under risk. Econometrica, 47, 263–292.MathSciNetCrossRefMATH

Kastner, I., & Stern, P. C. (2015). Examining the decision-making processes behind household energy investments: a review. Energy Research & Social Science, 10, 72–89. https://doi.org/10.1016/j.erss.2015.07.008.CrossRef

Kegel, M., Tamasauskas, J., Sunye, R., Giguère, D. (2014). Heat pumps in the Canadian residential sector. 11th IEA Heat Pump Conf. 2014 Montr. Canada 19.

Kirman, A. P. (1992). Whom or what does the representative individual represent? The Journal of Economic Perspectives, 6, 117–136.CrossRef

Knobloch, F., Mercure, J.-F., Pollitt, H., Chewpreecha, U., Lewney, R., 2017. A technical analysis of FTT:Heat—a simulation model for technological change in the residential heating sector. European Commission, Directorate-General for Energy.

Kolstad, C., Urama, K., Broome, J., Bruvoll, A., Olvera, M.C., Fullerton, D., Gollier, C., Hanemann, W.M., Hassan, R., Jotzo, F., Khan, M.R., Meyer, L., Mundaca, L. (2014). Social, economic and ethical concepts and methods. Clim. Chang. 2014 Mitig. Clim. Chang. Contrib. Work. Gr. III to Fifth Assess. Rep. Intergov. Panel Clim. Chang. 207–282.

Kranzl, L., Hummel, M., Müller, A., & Steinbach, J. (2013). Renewable heating: perspectives and the impact of policy instruments. Energy Policy, 59, 44–58. https://doi.org/10.1016/j.enpol.2013.03.050.CrossRef

Lamers, P., & Junginger, M. (2013). The “debt” is in the detail: a synthesis of recent temporal forest carbon analyses on woody biomass for energy. Biofuels, Bioproducts and Biorefining, 7, 373–385. https://doi.org/10.1002/bbb.1407.CrossRef

Lapsa, M., Khowailed, G., Sikes, K., Baxter, V. (2017). Heat pumps in North America—2017 regional report.

Li, F. G. N. (2017). Actors behaving badly: exploring the modelling of non-optimal behaviour in energy transitions. Energy Strategy Reviews, 15, 57–71. https://doi.org/10.1016/j.esr.2017.01.002.CrossRef

Li, F. G. N., Trutnevyte, E., & Strachan, N. (2015). A review of socio-technical energy transition (STET) models. Technological Forecasting and Social Change, 100, 290–305. https://doi.org/10.1016/j.techfore.2015.07.017.CrossRef

Lillemo, S. C. (2014). Measuring the effect of procrastination and environmental awareness on households’ energy-saving behaviours: an empirical approach. Energy Policy, 66, 249–256. https://doi.org/10.1016/j.enpol.2013.10.077.CrossRef

Lillemo, S., Alfnes, F., Halvorsen, B., & Wik, M. (2013). Households’ heating investments: the effect of motives and attitudes on choice of equipment. Biomass and Bioenergy, 57, 4–12.CrossRef

Lucon, O., Ürge-Vorsatz, D., Ahmed, A. Z., Akbari, H., Bertoldi, P., Cabeza, L. F., Eyre, N., Gadgil, A., Harvey, L. D. D., Jiang, Y., Liphoto, E., Mirasgedis, S., Murakami, S., Parikh, J., Pyke, C., & Vilariño, M. V. (2014). Buildings. In Climate Change 2014: Mitigation of Climate Change. Contribution of Working Group III to the Fifth Assessment Report of the Intergovernmental Panel on Climate Change. Cambridge: Cambridge University Press. https://doi.org/10.2753/JES1097-203X330403.

Lund, J. W., & Boyd, T. L. (2016). Direct utilization of geothermal energy 2015 worldwide review. Geothermics, 60, 66–93. https://doi.org/10.1016/j.geothermics.2015.11.004.CrossRef

Mahapatra, K., & Gustavsson, L. (2008). An adopter-centric approach to analyze the diffusion patterns of innovative residential heating systems in Sweden. Energy Policy, 36, 577–590. https://doi.org/10.1016/j.enpol.2007.10.006.CrossRef

Mauthner, F., Weiss, W., Spörk-Dür, M. (2016). Solar heat worldwide: markets and contribution to the energy supply 2014. IEA Sol. Heat. Cool. Program.

Mercure, J.-F. (2012). FTT:Power: a global model of the power sector with induced technological change and natural resource depletion. Energy Policy, 48, 799–811.CrossRef

Mercure, J.-F. (2015). An age structured demographic theory of technological change. Journal of Evolutionary Economics, 25, 787–820.CrossRef

Mercure, J.-F. (2017). Fashion, fads and the popularity of choices: micro-foundations for diffusion consumer theory. arXiv Prepr.

Mercure, J.-F., Pollitt, H., Chewpreecha, U., Salas, P., Foley, A. M., Holden, P. B., & Edwards, N. R. (2014). The dynamics of technology diffusion and the impacts of climate policy instruments in the decarbonisation of the global electricity sector. Energy Policy, 73, 686–700. https://doi.org/10.1016/j.enpol.2014.06.029.CrossRef

Mercure, J.-F., Pollitt, H., Bassi, A. M., Viñuales, J. E., & Edwards, N. R. (2016). Modelling complex systems of heterogeneous agents to better design sustainability transitions policy. Global Environmental Change, 37, 102–115. https://doi.org/10.1016/j.gloenvcha.2016.02.003.CrossRef

Mercure, J.-F., Pollitt, H., Edwards, N. R., Holden, P. B., Chewpreecha, U., Salas, P., Lam, A., Knobloch, F., & Vinuales, J. (2018). Environmental impact assessment for climate change policy with the simulation-based integrated assessment model E3ME-FTT-GENIE. Energy Strategy Reviews, 20, 195–208. https://doi.org/10.1016/j.esr.2018.03.003.CrossRef

Michelsen, C. C., & Madlener, R. (2012). Homeowners’ preferences for adopting innovative residential heating systems: a discrete choice analysis for Germany. Energy Economics, 34, 1271–1283. https://doi.org/10.1016/j.eneco.2012.06.009.CrossRef

Millar, R. J., Fuglestvedt, J. S., Friedlingstein, P., Rogelj, J., Grubb, M. J., Matthews, H. D., Skeie, R. B., Forster, P. M., Frame, D. J., & Allen, M. R. (2017). Emission budgets and pathways consistent with limiting warming to 1.5 °C. Nature Geoscience. https://doi.org/10.1038/ngeo3031.

Mundaca, L., & Markandya, A. (2016). Assessing regional progress towards a “green energy economy”. Applied Energy, 179, 1372–1394. https://doi.org/10.1016/j.apenergy.2015.10.098.CrossRef

Mundaca, L., Neij, L., Worrell, E., & McNeil, M. (2010). Evaluating energy efficiency policies with energy-economy models. Annual Review of Environment and Resources, 35, 305–344. https://doi.org/10.1146/annurev-environ-052810-164840.CrossRef

Mundaca, L., Markandya, A., & Nørgaard, J. (2013a). Walking away from a low-carbon economy? Recent and historical trends using a regional decomposition analysis. Energy Policy, 61, 1471–1480. https://doi.org/10.1016/j.enpol.2013.04.083.CrossRef

Mundaca, T. L., Mansoz, M., Neij, L., & Timilsina, G. R. (2013b). Transaction costs analysis of low-carbon technologies. Climate Policy, 13, 490–513. https://doi.org/10.1080/14693062.2013.781452.CrossRef

Newell, R. G., & Siikamäki, J. V. (2015). Time preferences and energy efficiency. American Economic Review: Papers and Proceedings, 105, 196–200. https://doi.org/10.1257/aer.p20151010.CrossRef

Newell, R. G., & Siikamki, J. (2015). Individual time preferences and energy efficiency. The American Economic Review, 105, 196–200. https://doi.org/10.1257/aer.p20151010.CrossRef

NREL. (2016). Distributed generation renewable energy estimate of costs (updated February 2016). National Renewable Energy Laboratory (NREL).

Olsthoorn, M., Schleich, J., Gassmann, X., & Faure, C. (2017). Free riding and rebates for residential energy efficiency upgrades: a multi-country contingent valuation experiment. Energy Economics, 68, 33–44. https://doi.org/10.1016/j.eneco.2018.01.007.CrossRef

PBL. (2018). User support system IMAGE scenarios [WWW document]. http://themasites.pbl.nl/models/image/index.php/Download

PHI. (2018). Passive house requirements [WWW Document]. URL http://www.passiv.de/en/02_informations/02_passive-house-requirements/02_passive-house-requirements.htm.

Rai, V., & Henry, A. D. (2016). Agent-based modelling of consumer energy choices. Nature Climate Change, 6, 556–562. https://doi.org/10.1038/nclimate2967.CrossRef

Riahi, K., van Vuuren, D. P., Kriegler, E., Edmonds, J., O’Neill, B. C., Fujimori, S., Bauer, N., Calvin, K., Dellink, R., Fricko, O., Lutz, W., Popp, A., Cuaresma, J. C., KC, S., Leimbach, M., Jiang, L., Kram, T., Rao, S., Emmerling, J., Ebi, K., Hasegawa, T., Havlik, P., Humpenöder, F., Da Silva, L. A., Smith, S., Stehfest, E., Bosetti, V., Eom, J., Gernaat, D., Masui, T., Rogelj, J., Strefler, J., Drouet, L., Krey, V., Luderer, G., Harmsen, M., Takahashi, K., Baumstark, L., Doelman, J. C., Kainuma, M., Klimont, Z., Marangoni, G., Lotze-Campen, H., Obersteiner, M., Tabeau, A., & Tavoni, M. (2017). The Shared Socioeconomic Pathways and their energy, land use, and greenhouse gas emissions implications: an overview. Global Environmental Change, 42, 153–168. https://doi.org/10.1016/J.GLOENVCHA.2016.05.009.CrossRef

Rivers, N., & Jaccard, M. (2005). Combining top-down and bottom-up approaches to energy-economy modeling using discrete choice methods. The Energy Journal, 26, 83–106.CrossRef

Rogelj, J., Luderer, G., Pietzcker, R. C., Kriegler, E., Schaeffer, M., Krey, V., & Riahi, K. (2015). Energy system transformations for limiting end-of-century warming to below 1.5 °C. Nature Climate Change, 5, 519–527. https://doi.org/10.1038/nclimate2572.CrossRef

Rogers, E. M. (2010). Diffusion of innovations. Simon and Schuster.

Schleich, J., Gassmann, X., Faure, C., & Meissner, T. (2016). Making the implicit explicit: a look inside the implicit discount rate. Energy Policy, 97, 321–331. https://doi.org/10.1016/j.enpol.2016.07.044.CrossRef

Shogren, J. F., & Taylor, L. O. (2008). On behavioral-environmental economics. Review of Environmental Economics and Policy, 2, 26–44. https://doi.org/10.1093/reep/rem027.CrossRef

Simon, H. A. (1955). A behavioral model of rational choice. Quarterly Journal of Economics, 69, 99–118.CrossRef

Sopha, B. M., Klöckner, C. A., Skjevrak, G., & Hertwich, E. G. (2010). Norwegian households’ perception of wood pellet stove compared to air-to-air heat pump and electric heating. Energy Policy, 38, 3744–3754. https://doi.org/10.1016/j.enpol.2010.02.052.CrossRef

Sopha, B. M., Klöckner, C. A., & Hertwich, E. G. (2011). Exploring policy options for a transition to sustainable heating system diffusion using an agent-based simulation. Energy Policy, 39, 2722–2729. https://doi.org/10.1016/j.enpol.2011.02.041.CrossRef

Stadler, M., Kranzl, L., Huber, C., Haas, R., & Tsioliaridou, E. (2007). Policy strategies and paths to promote sustainable energy systems—the dynamic Invert Simulation Tool. Energy Policy, 35, 597–608. https://doi.org/10.1016/j.enpol.2006.01.006.CrossRef

Steg, L. (2008). Promoting household energy conservation. Energy Policy, 36, 4449–4453. https://doi.org/10.1016/j.enpol.2008.09.027.CrossRef

Stern, P. C. (1986). Blind spots in policy analysis: what economics doesn’t say about energy use. Journal of Policy Analysis and Management, 5, 200–227.CrossRef

Sutherland, R. J. (1991). Market barriers to energy-efficiency investments. The Energy Journal, 12, 15–34.CrossRef

Train, K. (1985). Discount rates in consumers’ energy-related decisions: a review of the literature. Energy, 10, 1243–1253.CrossRef

Ürge-Vorsatz, D., Eyre, N., Graham, P., Harvey, D., Hertwich, E., Jiang, Y., Kornevall, C., Majumdar, M., McMahon, J., Mirasgedis, S., Murakami, S., Novikova, A. (2012a). Energy end-use: Buildings. In: Global energy assessment-toward a sustainable future. pp. 649–760.

Ürge-Vorsatz, D., Petrichenko, K., Antal, M., Staniec, M., Labelle, M., Ozden, E., Labzina, E. (2012b). Best practice policies for low energy and carbon buildings: A scenario analysis.

Urge-Vorsatz, D., Petrichenko, K., Staniec, M., & Eom, J. (2013). Energy use in buildings in a long-term perspective. Current Opinion in Environment Sustainability, 5, 141–151. https://doi.org/10.1016/j.cosust.2013.05.004.CrossRef

Ürge-Vorsatz, D., Cabeza, L. F., Serrano, S., Barreneche, C., & Petrichenko, K. (2015a). Heating and cooling energy trends and drivers in buildings. Renewable and Sustainable Energy Reviews, 41, 85–98. https://doi.org/10.1016/j.rser.2014.08.039.CrossRef

Ürge-Vorsatz, D., Reith, A., Korytarova, K., Egyed, M., Dollenstein, J. (2015b). Monetary benefits of ambitious building energy policies.

van Ruijven, B. J., van Vuuren, D. P., de Vries, B. J. M., Isaac, M., van der Sluijs, J. P., Lucas, P. L., & Balachandra, P. (2011). Model projections for household energy use in India. Energy Policy, 39, 7747–7761. https://doi.org/10.1016/j.enpol.2011.09.021.CrossRef

Wang, R., & Jiang, Z. (2017). Energy consumption in China’s rural areas: a study based on the village energy survey. Journal of Cleaner Production, 143, 452–461. https://doi.org/10.1016/J.JCLEPRO.2016.12.090.CrossRef

WBCSD. (2016). A handbook on creating dynamic local markets for energy efficiency in buildings.

Weiss, M., Junginger, M., Patel, M. K., & Blok, K. (2010). A review of experience curve analyses for energy demand technologies. Technological Forecasting and Social Change, 77, 411–428. https://doi.org/10.1016/j.techfore.2009.10.009.CrossRef

Wilhite, H., & Norgard, J. S. (2004). Equating efficiency with reduction: a self-deception in energy policy. Energy & Environment, 15, 991–1009. https://doi.org/10.1260/0958305043026618.CrossRef

Wilson, C. (2012). Up-scaling, formative phases, and learning in the historical diffusion of energy technologies. Energy Policy, 50, 81–94.CrossRef

Wilson, C., & Dowlatabadi, H. (2007). Models of decision making and residential energy use. Annual Review of Environment and Resources, 32, 169–203. https://doi.org/10.1146/annurev.energy.32.053006.141137.CrossRef

Wilson, C., & Grubler, A. (2011). Lessons from the history of technological change for clean energy scenarios and policies. Natural Resources Forum, 35, 165–184.CrossRef

Wilson, C., Crane, L., & Chryssochoidis, G. (2015). Why do homeowners renovate energy efficiently? Contrasting perspectives and implications for policy. Energy Research & Social Science, 7, 12–22. https://doi.org/10.1016/j.erss.2015.03.002.CrossRef

Worrell, E., Ramesohl, S., & Boyd, G. (2004). Advances in energy forecasting models based on engineering economics. Annual Review of Environment and Resources, 29, 345–381. https://doi.org/10.1146/annurev.energy.29.062403.102042.CrossRef

Zanchi, G., Pena, N., & Bird, N. (2012). Is woody bioenergy carbon neutral? A comparative assessment of emissions from consumption of woody bioenergy and fossil fuel. GCB Bioenergy, 4, 761–772. https://doi.org/10.1111/j.1757-1707.2011.01149.x.CrossRef

Titel: Simulating the deep decarbonisation of residential heating for limiting global warming to 1.5 °C
verfasst von: Florian Knobloch
Hector Pollitt
Unnada Chewpreecha
Vassilis Daioglou
Jean-Francois Mercure
Publikationsdatum: 05.07.2018
Verlag: Springer Netherlands
Erschienen in: Energy Efficiency / Ausgabe 2/2019
Print ISSN: 1570-646X
Elektronische ISSN: 1570-6478
DOI: https://doi.org/10.1007/s12053-018-9710-0

Springer Professional

Abstract

Electronic supplementary material

Introduction

Background and literature

Household decision-making

Modelling of the diffusion of heating systems

Methods and data

Simulating future heat demand with IMAGE-REMG

Simulating technology uptake with FTT:Heat

Decision-making by diverse households

Technology diffusion dynamics

Premature replacements

Learning by doing

Economic feedbacks

Energy demand

Technology data

Scenario definition

Results

Heat demand

Environmental effectiveness of policies

Cost-effectiveness of policies

Dynamics in an exemplary decarbonisation scenario

Discussion and conclusion

Acknowledgements

Compliance with ethical standards

Conflict of interest

Electronic supplementary material

Appendix

Estimation of intangible cost components

Detailed technology data

Regional technology pathways in scenario i

Weitere Artikel der Ausgabe 2/2019

Will policies to promote energy efficiency help or hinder achieving a 1.5 °C climate target?

Achievability of the Paris targets in the EU—the role of demand-side-driven mitigation in different types of scenarios

The transition in energy demand sectors to limit global warming to 1.5 °C

The potential contribution of disruptive low-carbon innovations to 1.5 °C climate mitigation

Carbon pricing and energy efficiency: pathways to deep decarbonization of the US electric sector

Demand-side approaches for limiting global warming to 1.5 °C