nach oben

Arabian Journal for Science and Engineering

Erschienen in:

09.03.2022 | Research Article-Mechanical Engineering

Morphology and Wear Behavior of Monolayer TiAlN and Composite AlCrN/TiAlN-Coated Plasma-Nitrided DAC-10 Tool Steel

verfasst von: Sunil Kumar, Saikat Ranjan Maity, Lokeswar Patnaik

Erschienen in: Arabian Journal for Science and Engineering | Ausgabe 12/2022

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

This experimental study focuses on the comparison of a monolayer of titanium–aluminum–nitride (TiAlN) and a composite of AlCrN/TiAlN coating where aluminum–chromium–nitride (AlCrN) deposited as an interlayer. These coatings have been deposited over heat-treated and plasma-nitrided DAC-10 tool steel using the physical vapor deposition (PVD) technique. Under this study, surface morphology, structural, nanomechanical, and wear behavior of these coated surfaces have been compared. Results suggest that surface roughness of bare nitrided DAC-10 tool steel decreased drastically and nanomechanical properties improved significantly upon coating. AlCrN/TiAlN coating exhibits a high strain hardening exponent (n) value which indicates lower maximum penetration depth and pile-up formation during nanoindentation, it also validates that AlCrN/TiAlN-coated surface comprises high hardness. The wear mechanisms of both the surfaces have been observed under FE-SEM with EDS; it reveals that severe adhesion of SAPH370 steel ball and heavy oxidation on both the coated surface. Even so, with high average arithmetic mean height and nanomechanical properties, AlCrN/TiAlN-coated surface performed better under nanoindentation and tribological test and it also reveals a lower wear rate under dry sliding conditions.

Vorheriger Artikel Significance of Lorentz Force and Viscous Dissipation on the Dynamics of Propylene Glycol: Water Subject to Joule Heating Conveying Paraffin Wax and Sand Nanoparticles Over an Object with a Variable Thickness

Nächster Artikel A Novel Slotted Cylinder Spring Geometry with an Improved Energy Storing Capacity

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Vipindas, K.; Mathew, J.: Wear behavior of TiAlN coated WC tool during micro end milling of Ti-6Al-4V and analysis of surface roughness. Wear 424, 165–182 (2019). https://doi.org/10.1016/j.wear.2019.02.018CrossRef

Kumar, S., Maity, S.R. and Patnaik, L.: Application of Box-Behnken Method for Multi-response Optimization of Turning Parameters for DAC-10 Hot Work Tool Steel. In Recent Advances in Mechanical Engineering (pp. 407-415) (2021). Springer, Singapore. https://doi.org/10.1007/978-981-15-7711-6_42

Mishra, K.S.; Ghosh, S.; Aravindan, S.: Characterization and machining performance of laser textured chevron shaped tools coated with AlTiN and AlCrN coatings. Surf. Coat. Technol. 334, 344–356 (2018). https://doi.org/10.1016/j.surfcoat.2017.11.061CrossRef

Chen, M.; Wu, D.; Chen, W.; Zhang, S.: Structural optimization and electrochemical behavior of AlCrN coatings. Thin Solid Films 612, 400–406 (2016). https://doi.org/10.1016/j.tsf.2016.06.032CrossRef

Gangatharan, K.; Selvakumar, N.; Narayanasamy, P.; Bhavesh, G.: Mechanical analysis and high temperature wear behaviour of AlCrN/DLC coated titanium alloy. Int. J. Surf. Sci. Eng. 10(1), 27–40 (2016). https://doi.org/10.1504/IJSURFSE.2016.075315CrossRef

Kumar, S.; Maity, S.R.; Patnaik, L.: Friction and tribological behavior of bare nitrided, TiAlN and AlCrN coated MDC-K hot work tool steel. Ceram. Int. 46(11), 17280–17294 (2020). https://doi.org/10.1016/j.ceramint.2020.04.015CrossRef

Patnaik, L.; Maity, S.R.; Kumar, S.: Modeling of wear parameters and multi-criteria optimization by box-behnken design of AlCrN thin film against gamma-irradiated Ti6Al4V counterbody. Ceram. Int. 47(14), 20494–20511 (2021). https://doi.org/10.1016/j.ceramint.2021.04.059CrossRef

Patnaik, L.; Maity, S.; Kumar, S.: Evaluation of crack resistance and adhesive energy of AlCrN and Ag doped aC Films deposited on Chrome Nitrided 316 LVM stainless steel. Mater. Process. Technol Adv (2021). https://doi.org/10.1080/2374068X.2021.1927643CrossRef

Patnaik, L.; Maity, S.R.; Kumar, S.: Evaluation of gamma irradiated Ti6Al4V and silver alloyed aC coatings as friction pair via response surface methodology. Mater. Process. Technol Adv (2021). https://doi.org/10.1080/2374068X.2021.1945277CrossRef

10.

Kumar, S.; Maity, S.R.; Patnaik, L.: Effect of heat treatment and TiN coating on AISI O1 cold work tool steel. Mater. Today: Proceed. 26(2), 685–688 (2020). https://doi.org/10.1016/j.matpr.2019.12.367CrossRef

11.

Patnaik, L.; Maity, S.R.; Kumar, S.: Status of nickel free stainless steel in biomedical field: a review of last 10 years and what else can be done. Mater. Today: Proceed. 26, 638–643 (2020). https://doi.org/10.1016/j.matpr.2019.12.205CrossRef

12.

Musfirah, A.H.; Ghani, J.A.; Haron, C.C.: Tool wear and surface integrity of inconel 718 in dry and cryogenic coolant at high cutting speed. Wear 376, 125–133 (2017). https://doi.org/10.1016/j.wear.2017.01.031CrossRef

13.

Ramanujam, R.; Vignesh, M.; Tamiloli, N.; Sharma, N.; Srivastava, S.; Patel, A.: Comparative evaluation of performances of TiAlN, AlCrN, AlCrN/TiAlN coated carbide cutting tools and uncoated carbide cutting tools on turning Inconel 825 alloy using grey relational analysis. Sens. Actuator. A: Phys. 279, 331–342 (2018). https://doi.org/10.1016/j.sna.2018.06.041CrossRef

14.

Kumar, T.S.; Prabhu, S.B.; Madhavan, S.B.; Padmanabhan, K.A.: Thermal stability of cathodic arc vapour deposited TiAlN/AlCrN and AlCrN/TiAlN coatings on tungsten carbide tool. Trans. Indian Inst. Metal. 71(3), 665–676 (2018). https://doi.org/10.1007/s12666-017-1199-2CrossRef

15.

Kumar, T.S., Jebaraj, A.V., Sivakumar, K., Mathivanan, P.: Machinability Studies of TiAlN-/AlCrN-Coated and Uncoated Tungsten Carbide Tools on Turning EN25 Alloy Steel. In Innovative Design. Analysis and Development Practices in Aerospace and Automotive Engineering (I-DAD). 213–221 (2018). https://doi.org/10.1007/978-981-13-2697-4_24

16.

Kumar, S.; Maity, S.R.; Patnaik, L.: Effect of tribological process parameters on the wear and frictional behaviour of Cr-(CrN/TiN) composite coating: an experimental and analytical study. Ceram. Int. 47(11), 16018–16028 (2021). https://doi.org/10.1016/j.ceramint.2021.02.176CrossRef

17.

Zhang, K.; Deng, J.; Guo, X.; Sun, L.; Lei, S.: Study on the adhesion and tribological behavior of PVD TiAlN coatings with a multi-scale textured substrate surface. Int. J. Refract. Metal Hard Mater. 72, 292–305 (2018). https://doi.org/10.1016/j.ijrmhm.2018.01.003CrossRef

18.

Kolesnikov, V.I.; Kudryakov, O.V.; Zabiyaka, I.Y.; Novikov, E.S.; Manturov, D.S.: Structural aspects of wear resistance of coatings deposited by physical vapor deposition. Phys. Mesomech. 23(6), 570–583 (2020). https://doi.org/10.1134/S1029959920060132CrossRef

19.

Kumar, T.S.; Prabu, S.B.; Kumar, T.S.: Comparative evaluation of performances of TiAlN-, AlCrN-and AlCrN/TiAlN-coated carbide cutting tools and uncoated carbide cutting tools on turning EN24 alloy steel. J. Adv. Manuf. Sys. 16(03), 237–261 (2017). https://doi.org/10.1142/S0219686717500159CrossRef

20.

Kumar, S., Maity, S.R. and Patnaik, L.: September. Relation between mechanical and tribological properties of plasma nitrided and TiCrN coated YXR-7 tool steel. In AIP Conference Proceedings (Vol. 2369, No. 1, p. 020033) (2021). AIP Publishing LLC. https://doi.org/10.1063/5.0061159

21.

Oliver, W.C.; Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater Res. 7(6), 1564–1583 (1992). https://doi.org/10.1557/JMR.1992.1564CrossRef

22.

Patnaik L, Maity S, Kumar S.: Comparative Study on The Structural Make-Up and Mechanical Behavior of Silicon and Silver Doped Amorphous Carbon Films. Silicon. 2022.

23.

Wang, Q.; Zhou, F.; Callisti, M.; Polcar, T.; Kong, J.; Yan, J.: Study on the crack resistance of CrBN composite coatings via nano-indentation and scratch tests. J. Alloy Comp. 708, 1103–1109 (2017). https://doi.org/10.1016/j.jallcom.2017.03.105CrossRef

24.

Wang, Q.; Zhou, F.; Yan, J.: Evaluating mechanical properties and crack resistance of CrN, CrTiN, CrAlN and CrTiAlN coatings by nanoindentation and scratch tests. Surf. Coat. Technol. 285, 203–213 (2016). https://doi.org/10.1016/j.surfcoat.2015.11.040CrossRef

25.

Kumar, S.; Maity, S.R.; Patnaik, L.: Wear assessment of Cr2O3/TiAlN coated DAC-10 tool steel against steel and Al2O3 counterbodies. Int. J. Appl. Ceram. Technol. (2021). https://doi.org/10.1111/ijac.13935CrossRef

26.

Łępicka, M.; Grądzka-Dahlke, M.; Pieniak, D.; Pasierbiewicz, K.; Kryńska, K.; Niewczas, A.: Tribological performance of titanium nitride coatings: A comparative study on TiN-coated stainless steel and titanium alloy. Wear 422, 68–80 (2019). https://doi.org/10.1016/j.wear.2019.01.029CrossRef

27.

Bourithis, L.; Papadimitriou, G.D.; Sideris, J.: Comparison of wear properties of tool steels AISI D2 and O1 with the same hardness. Tribol. Int. 39(6), 479–489 (2006). https://doi.org/10.1016/j.triboint.2005.03.005CrossRef

28.

Kumar, S.; Maity, S.R.; Patnaik, L.: A comparative study on wear behaviors of hot work and cold work tool steel with same hardness under dry sliding tribological test. Mater. Today: Proceed. 44, 949–954 (2021). https://doi.org/10.1016/j.matpr.2020.11.004CrossRef

29.

Patnaik, L.; Maity, S.R.; Kumar, S.: Comprehensive structural, nanomechanical and tribological evaluation of silver doped DLC thin film coating with chromium interlayer (Ag-DLC/Cr) for biomedical application. Ceram. Int. 46(14), 22805–22818 (2020). https://doi.org/10.1016/j.ceramint.2020.06.048CrossRef

30.

Patnaik, L.; Maity, S.R.; Kumar, S.: Mechanical and tribological assessment of composite AlCrN or aC: Ag-based thin films for implant application. Ceram. Int. 47(5), 6736–6752 (2021). https://doi.org/10.1016/j.ceramint.2020.11.016CrossRef

31.

Kumar, T.S.; Prabu, S.B.; Manivasagam, G.; Padmanabhan, K.A.: Comparison of TiAlN, AlCrN, and AlCrN/TiAlN coatings for cutting-tool applications. Int. J. Miner. Metall. Mater. 21(8), 796–805 (2014). https://doi.org/10.1007/s12613-014-0973-yCrossRef

32.

Elmkhah, H.; Fattah-alhosseini, A.; Babaei, K.; Abdollah-Zadeh, A.; Mahboubi, F.: Correlation between the Al content and corrosion resistance of TiAlN coatings applied using a PACVD technique. J. Asian Ceram. Soci. 8(1), 72–80 (2020). https://doi.org/10.1080/21870764.2019.1709274CrossRef

33.

Komarov, F.F.; Konstantinov, S.V.; Pilko, V.V.: Formation of nanostructured TiAlN, TiCrN, and TiSiN coatings using reactive magnetron sputtering. J. Fric. Wear. 35(3), 215–223 (2014). https://doi.org/10.3103/S1068366614030064CrossRef

34.

Xu, X.; Su, F.; Li, Z.: Tribological properties of nanostructured TiAlN/W2N multilayer coating produced by PVD. Wear 430, 67–75 (2019). https://doi.org/10.1016/j.wear.2019.04.021CrossRef

35.

Konstantinov, S.V.; Wendler, E.; Komarov, F.F.; Zaikov, V.A.: Radiation tolerance of nanostructured TiAlN coatings under Ar+ ion irradiation. Surf. Coat. Technol. 386, 125493 (2020). https://doi.org/10.1016/j.surfcoat.2020.125493CrossRef

36.

Khatibi, A.; Sjölen, J.; Greczynski, G.; Jensen, J.; Eklund, P.; Hultman, L.: Structural and mechanical properties of Cr–Al–O–N thin films grown by cathodic arc deposition. Acta Mater. 60(19), 6494–6507 (2012). https://doi.org/10.1016/j.actamat.2012.08.010CrossRef

37.

Grigoriev, S.; Vereschaka, A.; Milovich, F.; Sitnikov, N.; Andreev, N.; Bublikov, J.; Sadov, I.: Investigation of the Influence of microdroplets on the coatings nanolayer structure. Coating. 10(12), 1204 (2020). https://doi.org/10.3390/coatings10121204CrossRef

38.

Kumar, S.; Maity, S.R.; Patnaik, L.: Effect of annealing on structural, mechanical and tribological properties of Cr-(CrN/TiAlN) coating. Mater. Process. Technol Adv (2021). https://doi.org/10.1080/2374068X.2021.1946755CrossRef

39.

Patnaik, L.; Maity, S.R.; Kumar, S.: Effect of lubricated sliding wear against CFRPEEK on the nanomechanical properties of Ag alloyed Cr/DLC thin film. J. Mech. Behav. Biomed. Mater. 118, 104478 (2021). https://doi.org/10.1016/j.jmbbm.2021.104478CrossRef

40.

Patnaik, L.; Maity, S.R.; Kumar, S.: Lubricated sliding of CFRPEEK/AlCrN film tribo-pair and its effect on the mechanical properties and structural integrity of the AlCrN film. Mater. Chem. Phys. 273, 124980 (2021). https://doi.org/10.1016/j.matchemphys.2021.124980CrossRef

41.

Xu, X.Y.; Chen, L.; Pei, F.; Yue, J.L.; Du, Y.: Thermal stability and oxidation resistance of Valloyed TiAlN coatings. Ceram. Int. 44(2), 1705–1710 (2018). https://doi.org/10.1016/j.ceramint.2017.10.100CrossRef

42.

Geng, Z.; Shi, G.; Shao, T.; Liu, Y.; Duan, D.; Reddyhoff, T.: Tribological behavior of patterned TiAlN coatings at elevated temperatures. Surf. Coat. Technol. 364, 99–114 (2019). https://doi.org/10.1016/j.surfcoat.2019.02.076CrossRef

43.

Chang, Y.Y.; Wang, Y.D.; Hung, Y.C.: Structural and mechanical properties of nanolayered TiAlN/CrN coatings synthesized by a cathodic arc deposition process. Surf. Coat. Technol. 200(5–6), 1702–1708 (2005). https://doi.org/10.1016/j.surfcoat.2005.08.088CrossRef

44.

Barshilia, H.C.; Deepthi, B.; Selvakumar, N.; Jain, A.; Rajam, K.S.: Nanolayered multilayer coatings of CrN/CrAlN prepared by reactive DC magnetron sputtering. Appl. Surf. Sci. 253(11), 5076–5083 (2007). https://doi.org/10.1016/j.apsusc.2006.11.021CrossRef

45.

Soldán, J.; Neidhardt, J.; Sartory, B.; Kaindl, R.; Čerstvý, R.; Mayrhofer, P.H.; Tessadri, R.; Polcik, P.; Lechthaler, M.; Mitterer, C.: Structure-property relations of arc-evaporated Al−Cr−Si−N coatings. Surf. Coat. Technol. 202(15), 3555–3562 (2008). https://doi.org/10.1016/j.surfcoat.2007.12.041CrossRef

46.

Kumar, T.S.; Prabu, S.B.; Manivasagam, G.: Metallurgical characteristics of TiAlN/AlCrN coating synthesized by the PVD process on a cutting insert. J. Mater. Eng. Perform. 23(8), 2877–2884 (2014). https://doi.org/10.1007/s11665-014-1057-xCrossRef

47.

Subramanian, B.; Muraleedharan, C.V.; Ananthakumar, R.; Jayachandran, M.: A comparative study of titanium nitride (TiN), titanium oxy nitride (TiON) and titanium aluminum nitride (TiAlN), as surface coatings for bio implants. Surf. Coat. Technol. 205(21–22), 5014–5020 (2011). https://doi.org/10.1016/j.surfcoat.2011.05.004CrossRef

48.

Chang, L.C.; Huang, S.C.; Jao, Y.J.: Microstructural, mechanical and wear properties of Cr–Al–B–N coatings deposited by DC reactive magnetron co-sputtering. Surf. Coat. Technol. 205(8–9), 2730–2737 (2011). https://doi.org/10.1016/j.surfcoat.2010.10.023CrossRef

49.

Alaskari, A.M.; Oraby, S.E.; Almazrouee, A.I.: SEM and AFM investigations of surface defects and tool wear of multilayers coated carbide inserts. Int. J. Mech. Mechatron. Eng. 5(1), 118–122 (2011)

50.

Barshilia, C.H.; Rajam, S.K.: Raman spectroscopy studies on the thermal stability of TiN, CrN, TiAlN coatings and nanolayered TiN/CrN. TiAlN/CrN multilayer coatings. J. Mater. Res. 19(11), 3196–3205 (2004)CrossRef

51.

Łępicka, M.; Grądzka-Dahlke, M.; Pieniak, D.; Pasierbiewicz, K.; Niewczas, A.: Effect of mechanical properties of substrate and coating on wear performance of TiN-or DLC-coated 316LVM stainless steel. Wear 382, 62–70 (2017). https://doi.org/10.1016/j.wear.2017.04.017CrossRef

52.

Sribalaji, M.; Rahman, O.A.; Laha, T.; Keshri, A.K.: Nanoindentation and nanoscratch behavior of electroless deposited nickel-phosphorous coating. Mater. Chem. Phys. 177, 220–228 (2016). https://doi.org/10.1016/j.matchemphys.2016.04.022CrossRef

53.

Gale, D.L.; Achuthan, A.: The effect of work-hardening and pile-up on nanoindentation measurements. J. Mater. Sci. 49(14), 5066–5075 (2014). https://doi.org/10.1007/s10853-014-8213-4CrossRef

54.

Schaefer, H.E.; Würschum, R.; Birringer, R.; Gleiter, H.: Structure of nanometer-sized polycrystalline iron investigated by positron lifetime spectroscopy. Phys. Rev. B. 38(14), 9545 (1988). https://doi.org/10.1103/PhysRevB.38.9545CrossRef

55.

Sujith, R.; Kumar, R.: Experimental investigation on the indentation hardness of precursor derived Si–B–C–N ceramics. J. Eur. Ceram. 33(13–14), 2399–2405 (2013). https://doi.org/10.1016/j.jeurceramsoc.2013.04.025CrossRef

56.

Lost, A.; Bigot, R.: Hardness of coatings. Surf. Coat. Technol. 80(1–2), 117–120 (1996). https://doi.org/10.1016/0257-8972(95)02697-5CrossRef

57.

Rodriguez-Baracaldo, R.; Benito, J.A.; Puchi-Cabrera, E.S.; Staia, M.H.: High temperature wear resistance of (TiAl) N PVD coating on untreated and gas nitrided AISI H13 steel with different heat treatments. Wear 262(3–4), 380–389 (2007). https://doi.org/10.1016/j.wear.2006.06.010CrossRef

58.

Wang, Q.; Zhou, F.; Zhou, Z.; Li, L.K.Y.; Yan, J.: An investigation on the crack resistance of CrN, CrBN and CrTiBN coatings via nanoindentation. Vacuum 145, 186–193 (2017). https://doi.org/10.1016/j.vacuum.2017.08.041CrossRef

59.

Torres, R.D.; Soares, P.C., Jr.; Schmitz, C.; Siqueira, C.J.: Influence of the nitriding and TiAlN/TiN coating thickness on the sliding wear behavior of duplex treated AISI H13 steel. Surf. Coat. Technol. 205(5), 1381–1385 (2010). https://doi.org/10.1016/j.surfcoat.2010.07.102CrossRef

60.

Kumar, S.; Maity, S.R.; Patnaik, L.: Mechanical and Scratch behaviour of TiAlN Coated and 3D Printed H13 Tool Steel. Mater. Process. Technol Adv (2021). https://doi.org/10.1080/2374068X.2021.1927642CrossRef

61.

Grzesik, W.; Zalisz, Z.; Król, S.: Tribological behaviour of TiAlN coated carbides in dry sliding tests. J. Achiev. Mater. Manuf. Eng. 17(1–2), 181–184 (2006)

62.

Tillmann, W.; Vogli, E.; Momeni, S.: Mechanical and tribological properties of Ti/TiAlN duplex coatings on high and low alloy tool steels. Vacuum 84(3), 387–392 (2009). https://doi.org/10.1016/j.vacuum.2009.08.001CrossRef

63.

Kabir, M.S.; Munroe, P.; Zhou, Z.; Xie, Z.: Scratch adhesion and tribological behaviour of graded Cr/CrN/CrTiN coatings synthesized by closed-field unbalanced magnetron sputtering. Wear 380, 163–175 (2017). https://doi.org/10.1016/j.wear.2017.03.020CrossRef

64.

Liang, Q.; Stanishevsky, A.; Vohra, Y.K.: Tribological properties of undoped and boron-doped nanocrystalline diamond films. Thin Solid Films 517(2), 800–804 (2008). https://doi.org/10.1016/j.tsf.2008.08.171CrossRef

65.

Grzesik, W.; Zalisz, Z.; Krol, S.; Nieslony, P.: Investigations on friction and wear mechanisms of the PVD-TiAlN coated carbide in dry sliding against steels and cast iron. Wear 261(11–12), 1191–1200 (2006). https://doi.org/10.1016/j.wear.2006.03.004CrossRef

66.

Vettivel, S.C.; Jegan, R.; Vignesh, J.; Suresh, S.: Surface characteristics and wear depth profile of the TiN, TiAlN and AlCrN coated stainless steel in dry sliding wear condition. Surf. Interface. 6, 1–10 (2017). https://doi.org/10.1016/j.surfin.2016.10.008CrossRef

67.

Saravanan, I.; Perumal, A.E.; Issac, R.F.; Vettivel, S.C.; Devaraju, A.: Optimization of wear parameters and their relative effects on TiN coated surface against Ti6Al4V alloy. Mater. Des. 92, 23–35 (2016). https://doi.org/10.1016/j.matdes.2015.11.119CrossRef

68.

Paskvale, S.; Remškar, M.; Čekada, M.: Tribological performance of TiN, TiAlN and CrN hard coatings lubricated by MoS2 nanotubes in Polyalphaolefin oil. Wear 352, 72–78 (2016). https://doi.org/10.1016/j.wear.2016.01.020CrossRef

69.

Huang, X.; Etsion, I.; Shao, T.: Effects of elastic modulus mismatch between coating and substrate on the friction and wear properties of TiN and TiAlN coating systems. Wear 338, 54–61 (2015). https://doi.org/10.1016/j.wear.2015.05.016CrossRef

70.

Kumar, V.; Sinha, S.K.; Agarwal, A.K.: Tribological studies of dual-coating (intermediate hard with top epoxy-graphene-base oil composite layers) on tool steel in dry and lubricated conditions. Tribol. Int. 127, 10–23 (2018). https://doi.org/10.1016/j.triboint.2018.05.011CrossRef

71.

Jiahong, L.; Dejun, K.: Characteristics and tribological behaviors of TiAlN/Cr-Ni composite coatings at elevated temperatures. J. Mater. Eng. Perform. 28(11), 7075–7085 (2019). https://doi.org/10.1007/s11665-019-04429-wCrossRef

72.

So, H.; Yu, D.S.; Chuang, C.Y.: Formation and wear mechanism of tribo-oxides and the regime of oxidational wear of steel. Wear 253(9–10), 1004–1015 (2002). https://doi.org/10.1016/S0043-1648(02)00230-2CrossRef

Titel: Morphology and Wear Behavior of Monolayer TiAlN and Composite AlCrN/TiAlN-Coated Plasma-Nitrided DAC-10 Tool Steel
verfasst von: Sunil Kumar
Saikat Ranjan Maity
Lokeswar Patnaik
Publikationsdatum: 09.03.2022
Verlag: Springer Berlin Heidelberg
Erschienen in: Arabian Journal for Science and Engineering / Ausgabe 12/2022
Print ISSN: 2193-567X
Elektronische ISSN: 2191-4281
DOI: https://doi.org/10.1007/s13369-022-06711-x

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 12/2022

Impact of Equally Diffusive Chemical Reaction on Time-Dependent Flow of Casson Nanofluid Due to Oscillatory Curved Stretching Surface with Thermal Radiation

Heat and Mass Transfer in 3D MHD Flow of EG-Based Ternary Hybrid Nanofluid Over a Rotating Surface

Numerical and Experimental Investigation of Fracture in Roll Forming Process Using Lou–Huh Fracture Criterion

Multi-Objective Optimization of Parallel Cross Multi-Effect Desalination Systems with Thermal Vapor Compression

Estimation and Comparison of Effective Elastic Modulus of Different Scaffolds Using Curve Fitting Method for Additive Manufacturing Field

Heat Transfer and Fluid Flow Characterıstics in a Long Offset Strip Fin Channel by Using TIO2-Water Nanofluıd

Premium Partner

Marktübersichten