nach oben

Arabian Journal for Science and Engineering

Erschienen in:

07.01.2021 | Research Article-Mechanical Engineering

Multipoint Acceleration Information Acquisition of the Impact Experiments Between Coal Gangue and the Metal Plate and Coal Gangue Recognition Based on SVM and Serial Splicing Data

verfasst von: Yang Yang, Qingliang Zeng

Erschienen in: Arabian Journal for Science and Engineering | Ausgabe 3/2021

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Impact contact behaviors with different velocities, direction and contact states occurred in the process of coal drawing between coal gangue particles and the hydraulic support greatly increase the difficulty of coal gangue recognition in top coal caving. In order to finally realize coal gangue recognition in top coal caving, this paper studied the impact behavior of a single particle coal gangue and the metal plate at any position and the problem of the identification of coal gangue particles. First, the any position impacting test bench and test system is constructed, in which multipoint acceleration information acquisition space is built. Second, 2400 groups of random impact tests between coal gangue particle and the metal plate are conducted. Third, while each impact test was going on, acceleration signals in the seven different positions of the metal plate were collected. Forth, after all the impact tests are completed, signals are processed by segmentation and re-sorted by randomization. Then, the method of signals serial splicing is proposed to process the different position standardized signals obtained in each group of impact test, and coal gangue recognition is proposed based on processed signal data and SVM algorithm. After that, the effect of parameters on coal gangue recognition accuracy of SVM algorithm is studied, and the corresponding parameter settings of SVM are accordingly determined. Finally, coal gangue recognition was conducted by using SVM based on different data samples, the influence law of the training set data set expansion method and the test set data matching relationship, the number of tandem sensors and matching relationship, and the number of training set samples on coal gangue recognition accuracy were studied. The study will serve as the research basis for the application of SVM and signals serial splicing method in coal gangue recognition.

Vorheriger Artikel Multi-objective optimization and Surface Morphology of M-42 AISI Steel Using Normal and Cryo-treated Brass Wire in Wire Cut EDM

Nächster Artikel Production of Micro-holes on Duplex Stainless Steel 2205 by Electrochemical Micromachining: A Grey-RSM Approach

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Yu, B.; Zhao, J.; Xiao, H.T.: Case study on overburden fracturing during longwall top coal caving using microseismic monitoring. Rock Mech. Rock Eng. 50, 507–511 (2017). https://doi.org/10.1007/s00603-016-1096-8CrossRef

Zhang, J.W.; Wang, J.C.; Wei, W.J.; Chen, Y.; Song, Z.Y.: Experimental and numerical investigation on coal drawing from thick steep seam with longwall top coal caving mining. Arab. J. Geosci. 11, 96 (2018). https://doi.org/10.1007/s12517-018-3421-xCrossRef

Vakilin, A.; Hebblewhite, B.K.: A new cavability assessment criterion for Longwall Top Coal Caving. Int. J. Rock Mech. Min. Sci. 47, 1317–1329 (2010). https://doi.org/10.1016/j.ijrmms.2010.08.010CrossRef

Lin, C.-C.; Deng, D.-J.; Chen, Zheng-Yu; Chen, K.-C.: Key design of driving industry 4.0: joint energy-efficient deployment and scheduling in group-based industrial wireless sensor networks. IEEE Commun. Magazine. 54(10), 46–52 (2016). https://doi.org/10.1109/mcom.2016.7588228CrossRef

Patel, P.; Ali, M.; Sheth, A.: From raw data to smart manufacturing: ai and semantic web of things for industry 4.0. IEEE Intell. Syst. 33(4), 79–86 (2018). https://doi.org/10.1109/mis.2018.043741325CrossRef

Posada, J.; Zorrilla, M.; Dominguez, A.; Simoes, B.; Eisert, P.; Stricker, D.; Rambach, J.; Dollner, J.; Guevara, M.: Graphics and Media Technologies for Operators in Industry 40. IEEE Comput. Graph. Appl. 38(5), 119–132 (2018). https://doi.org/10.1109/mcom.2016.7588228CrossRef

Lin, C.-C.; Yang, J.-W.: Cost-efficient deployment of fog computing systems at logistics centers in industry 4.0. IEEE Trans. Ind. Inf. 14(10), 4603–4611 (2018). https://doi.org/10.1109/tii.2018.2827920CrossRef

Yu, B.; Xu, G.; Huang, Z.Z.; Guo, J.G.; Li, Z.; Li, D.Y.; Wang, S.B.; Meng, E.C.; Pan, W.D.; Niu, J.F.; Xue, J.S.; Zhao, T.L.: Theory and its key technology framework of intelligentized fully-mechanized caving mining in extremely thick coal seam. J. China Coal Soc. 44(1), 42–53 (2019). https://doi.org/10.13225/j.cnki.jccs.2018.5050CrossRef

Si, L.; Wang, Z.B.; Liu, X.H.; Tan, C.; Xu, J.; Zheng, K.H.: Multi-sensor data fusion identification for shearer cutting conditions based on parallel quasi-Newton neural networks and the Dempster-Shafer theory. Sensors 15(11), 28772–28795 (2015). https://doi.org/10.3390/s151128772CrossRef

10.

Xu, J.; Wang, Z.B.; Tan, C.; Si, L.; Liu, X.H.: A cutting pattern recognition method for shearers based on improved ensemble empirical mode decomposition and a probabilistic neural network [J]. Sensors 15(11), 27721–27737 (2015). https://doi.org/10.3390/s151127721CrossRef

11.

Ren, F.; Yang, Z.J.; Xiong, S.B.: Study on the coal-rock interface recognition method based on multi-sensor data fusion technique. Chin. J. Mech. Eng. 16(3), 321–324 (2003). https://doi.org/10.3901/CJME.2003.03.321CrossRef

12.

Tian, L.Y.; Mao, J.; Wang, Q.M.: Coal and rock identification method based on the force of idler shaft in shearer’s ranging arm. J. China Coal Soc. 41(3), 782–787 (2016). https://doi.org/10.13225/j.cnki.jccs.2015.0576CrossRef

13.

Zhang, N.; Liu, C.: Radiation characteristics of natural gamma-ray from coal and gangue for recognition in top coal caving. Sci. Rep. 8(1), 190 (2018). https://doi.org/10.1038/s41598-017-18625-yMathSciNetCrossRef

14.

Wang, W.; Zhang, C.: Separating coal and gangue using three-dimensional laser scanning. Int. J. Miner. Process. 694, 79–84 (2017). https://doi.org/10.1016/j.minpro.2017.10.010CrossRef

15.

Chen, C.: Study on the recognition of coal and rock cutting state and the control strategy of shearer. School of electrical and control engineering, Xi’an University of Science and Technology. Master’s thesis. Xi’an, China, (2019)

16.

Wang, Z.; Si, L.; Tan, C.; Liu, X.: A novel approach for shearer cutting load identification through integration of improved particle swarm optimization and wavelet neural network. Adv. Mech. Eng. (2014). https://doi.org/10.1155/2014/521629CrossRef

17.

Si, L.; Wang, Z.; Liu, X.; Tan, C.; Zhang, L.: Cutting state diagnosis for shearer through the vibration of rocker transmission part with an improved probabilistic neural network. Sensors 16(4), 479 (2016). https://doi.org/10.3390/s16040479CrossRef

18.

Xu, J.; Wang, Z.B.; Tan, C.; Si, L.; Liu, X.H.: Cutting pattern identification for coal mining shearer through a swarm intelligence–based variable translation wavelet neural network. Sensors 18(2), 382 (2018). https://doi.org/10.3390/s16040479CrossRef

19.

Huang, S.J.: The coal-rock interface recognition research based on the digital image processing and clustering technology, Doctor thesis, School of Mechanical Electronic & Information Engineering, China University of Mining & Technology (Beijing). Beijing, China (2016)

20.

Wang, X.: Study of Coal-Rock Identification Method Based on Electromagnetic Wave Technology. Doctor’s thesis. School of Information and Control Engineering, China University of Mining & Technology, Jiangsu Sheng, China, (2017)

21.

Sun J.; Su B.: Coal − rock interface detection using digital image analysis technique. In: Wang X.; Wang F.; Zhong S. (eds) Electrical, Information Engineering and Mechatronics 2011. Lecture Notes in Electrical Engineering, vol 138. Springer, London. (2012). https://doi.org/10.1007/978-1-4471-2467-2_144

22.

Zhang, W.; Li, G. H.; Hu, B.: The study of coal-rock boundary identification and height adjustment of Miner drum based on multi-parameter[C]//International Conference on Information Science & Engineering. IEEE, (2011). https://doi.org/10.1109/icise.2010.5691627

23.

Wang, H.J.: Theoretical and Experimental Study on Coal-rock Interface Identification Based on Multi Information Fusion. Doctor’s thesis. School of Mechanical Engineering, Liaoning Technical University, 2017, Liaoning, China

24.

Tian, L.Y.; Dai, B.H.; Wang, Q.M.: Coal-rock identification method based on multi-strain data fusion of shearer rocker pin shaft. J. China Coal Soc. (2019). https://doi.org/10.13225/j.cnki.jccs.2019.0364CrossRef

25.

Wei, H.: Identification of coal and gangue by feed-forward neural network based on data analysis. Int. J. Coal Preparation Utilization 39(1), 33–43 (2019). https://doi.org/10.1080/19392699.2017.1290609CrossRef

26.

Wang, J.C.; Li, L.H.; Yang, S.L.: Experimental study on gray and texture features extraction of coal and gangue image under different illuminance. J. China Coal Soc. 43(11), 3051–3061 (2018). https://doi.org/10.13225/j.cnki.jccs.2018.0866CrossRef

27.

Sun, J.P.; Su, B.: Coal–rock interface detection on the basis of image texture features. Int. J. Min. Sci. Technol. 23(05), 681–687 (2013). https://doi.org/10.1016/j.ijmst.2013.08.011CrossRef

28.

Dou, D.Y.; Zhou, D.Y.; Yang, J.G.; Zhang, Y.: Coal and gangue recognition under four operating conditions by using image analysis and Relief-SVM. Int. J. Coal Preparation Utiliz. (2018). https://doi.org/10.1080/19392699.2018.1540416CrossRef

29.

Liu, F.Q.; Qian, J.S.; Wang, X.H.; Song, J.L.: Automatic separation of waste rock in coal mine based on image procession and recognition. J. China Coal Soc. 25(5), 534–537 (2000). https://doi.org/10.13225/j.cnki.jccs.2000.05.020CrossRef

30.

Li, L.; Wang, H.; An, L.: Research on recognition of coal and gangue based on image processing. World J. Eng. 12(3), 247–254 (2015). https://doi.org/10.1260/1708-5284.12.3.247CrossRef

31.

Yu, L.; Zheng, L.X.; Du, Y.Z.; Huang, X.: Image recognition method of coal and coal gangue based on partial grayscale compression extended coexistence matrix. J. Huaqiao Univ. Nat. Sci. 39(6), 906–912 (2018). https://doi.org/10.11830/ISSN.1000-5013.201610012CrossRef

32.

Liu, K.: The Study on Image Recognition of Coal and Gangue Boundary Signatures Based on the Fractional Calculus. Doctor’s thesis. School of mechanical electronic & information engineering, China University of Mining & Technology (Beijing). Beijing, China, (2018)

33.

Liu, W.; He, K.; Liu, C.Y.; Gao, Q.; Yan, Y.H.: Coal-gangue interface detection based on Hilbert spectral analysis of vibrations due to rock impacts on a longwall mining machine[J]. Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci. 229(8), 1523–1531 (2015). https://doi.org/10.1177/0954406214543409CrossRef

34.

Song, Q.-j.; Jiang, H.-y.; Zhao, X.; Li, D.-m.: An automatic decision approach to coal–rock recognition in top coal caving based on MF-Score. Pattern Anal. Appl. 20(4), 1307–1315 (2017). https://doi.org/10.1007/s10044-017-0618-7MathSciNetCrossRef

35.

Song, Q.; Jiang, H.; Song, Q.; Zhao, X.; Wu, X.: Combination of minimum enclosing balls classifier with SVM in coal-rock recognition. PLoS ONE 12(9), e0184834 (2017). https://doi.org/10.1371/journal.pone.0184834CrossRef

36.

Zhang, G.; Wang, Z.; Zhao, L.: Recognition of rock–coal interface in top coal caving through tail beam vibrations by using stacked sparse autoencoders. J. VibroEng. 18(7), 4261–4275 (2016). https://doi.org/10.21595/jve.2016.17386CrossRef

37.

Yang, Y.; Zeng, Q.; Wan, L.: Dynamic response analysis of the vertical elastic impact of the spherical rock on the metal plate. Int. J. Solids Struct. 158, 287–302 (2019). https://doi.org/10.1016/j.ijsolstr.2018.09.017CrossRef

38.

Yang, Y.; Zeng, Q.L.; Yin, G.J.; Wan, L.R.: Vibration test of single coal gangue particle directly impacting the metal plate and the study of coal gangue recognition based on vibration signal and stacking integration. IEEE Access. 7, 106784–106805 (2019). https://doi.org/10.1109/ACCESS.2019.2932118CrossRef

39.

Axelberg, P.G.V.; Gu, Y.H.; Bollen, M.H.J.: Support vector machine for classification of voltage disturbances. IEEE Trans. Power Deliv. (2007). https://doi.org/10.1109/tpwrd.2007.900065CrossRef

40.

Erfani, S.M.; Rajasegarar, S.; Karunasekera, S.; Leckie, C.: ‘High-dimensional and large-scale anomaly detection using a linear one-class SVM with deep learning’. Pattern Recognit. 58, 121–134 (2016). https://doi.org/10.1016/j.patcog.2016.03.028CrossRef

41.

Pandarakone, S.E.; Mizuno, Y.; Nakamura, H.: Distinct fault analysis of induction motor bearing using frequency spectrum determination and support vector machine. IEEE Trans. Ind. Appl. 53(3), 3049–3056 (2017). https://doi.org/10.1109/TIA.2016.2639453CrossRef

42.

Jan, S.U.; Lee, Y.D.; Shin, J.; Koo, I.: Sensor fault classification based on support vector machine and statistical time-domain features. IEEE Access 5, 8682–8690 (2017). https://doi.org/10.1109/ACCESS.2017.2705644CrossRef

43.

Zhang, X.; Liang, Y.; Zhou, J.: A novel bearing fault diagnosis model integrated permutation entropy, ensemble empirical mode decomposition and optimized SVM’. Measurement 69, 164–179 (2015). https://doi.org/10.1016/j.measurement.2015.03.017CrossRef

44.

Park, Y.W.; Baskiyar, S.: Adaptive scheduling on heterogeneous systems using support vector machine. Computing 99(4), 405–425 (2017). https://doi.org/10.1007/s00607-016-0513-xMathSciNetCrossRef

45.

Bae, K.Y.; Jang, H.S.; Sung, D.K.: Hourly solar irradiance prediction based on support vector machine and its error analysis. IEEE Trans. Power Syst. 32(2), 935–945 (2017). https://doi.org/10.1109/TPWRS.2016.2569608CrossRef

46.

Saad, O.M.; Shalaby, A.; Sayed, M.S.: Automatic discrimination of earthquakes and quarry blasts using wavelet filter bank and support vector machine. J. Seismolog. (2018). https://doi.org/10.1007/s10950-018-9810-5CrossRef

47.

Wang, Y.; Fu, J.; Pan, W.D.: Impact of setting margin on margin setting algorithm and support vector machine. J. Imag. Sci. Technol. 62(3), 1 (2018). https://doi.org/10.2352/j.imagingsci.technol.2018.62.3.030501CrossRef

48.

Zeng, J.; Lu, D.; Zhao, Y.; Zhang, Z.; Qiao, W.; Gong, X.: Wind turbine fault detection and isolation using support vector machine and a residual-based method. Proc. Amer. Control Conf. (2013). https://doi.org/10.1109/acc.2013.6580398CrossRef

49.

Hackeling, G. (Write); Zhang, H.R. (Translate): Mastering Machine Learning with scikit-learn Second Edition. Posts and Telecom Press. Beijing, China, (2019)

Titel: Multipoint Acceleration Information Acquisition of the Impact Experiments Between Coal Gangue and the Metal Plate and Coal Gangue Recognition Based on SVM and Serial Splicing Data
verfasst von: Yang Yang
Qingliang Zeng
Publikationsdatum: 07.01.2021
Verlag: Springer Berlin Heidelberg
Erschienen in: Arabian Journal for Science and Engineering / Ausgabe 3/2021
Print ISSN: 2193-567X
Elektronische ISSN: 2191-4281
DOI: https://doi.org/10.1007/s13369-020-05227-6

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 3/2021

A Coscheduling Model of Automated Single-Beam Cranes and AGVs in Assembly Workshop

Experimental Investigation on Tool Wear in AISI H13 Die Steel Turning Using RSM and ANN Methods

Reproducibility of Replicated Trabecular Bone Structures from Ti6Al4V Extralow Interstitials Powder by Selective Laser Melting

Real-Time Stabilization Control of a Rotary Inverted Pendulum Using LQR-Based Sliding Mode Controller

Liquid Paraffin Thermal Conductivity with Additives Tungsten Trioxide Nanoparticles: Synthesis and Propose a New Composed Approach of Fuzzy Logic/Artificial Neural Network

Prediction Model of Dilatancy Stress Based on Brittle Rock: A Case Study of Sandstone

Premium Partner

Marktübersichten