nach oben

Arabian Journal for Science and Engineering

Erschienen in:

28.03.2023 | Research Article-Mechanical Engineering

Optimization of Engine Parameters Using Taguchi Technique for a Diesel Engine Running on a Newly Developed bio-nano Diesel Emulsion

verfasst von: Narender Singh, Rajneesh Kaushal

Erschienen in: Arabian Journal for Science and Engineering | Ausgabe 9/2023

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Currently, the globe is experiencing a difficult energy-related situation. Although nanotechnology has the potential to significantly advance a wide range of disciplines, there are concerns about the potential risks of its products and applications. Thus, the present research proposed a newly developed bio-nano diesel emulsion fuel for energy conservation, pollution reduction and improved diesel engine efficiency. The biodegradable carbon quantum dots (CQDs) were produced via a hydrothermal technique using waste sweet lime peel and were subsequently well characterized in terms of morphology. Water and carbon quantum dots were added to the biodiesel blends at increasing 25, 50, and 75 ppm concentrations. Using the Taguchi Technique, DOE-recommended tests have been carried out systematically. The engine load, compression ratio, engine speed, water, and CQD were considered input parameters for optimizing BP, BSFC, BTE, NOx, CO, HC, and smoke emissions of a biodiesel blend engine. The model recommended an optimal solution that fulfilled the indicated optimum input parameters of 42% engine load, 18 compression ratio, 1800 rpm engine speed, 10% water, and 75 ppm CQD using the desirability method. The optimum performance and emission characteristics (BP, BSFC, BTE, NOx, HC, CO, and smoke) are found to be 2.48 kW, 294 g/kWh, 30.36%, 317 ppm, 0.81 ppm, 0.0011%, and 5.27 HSU, respectively. The tested inaccuracy of optimum blend interactions for BP, BSFC, BTE, NOx, HC, CO, and smoke was determined to be 9.25%, 1.38%, 2.08%, 6.30%, 5.63%, 7.69%, and 0.75%, respectively, within acceptable limits.

Vorheriger Artikel Design and Experimental Validation of an Adaptive Landing Gear for Safe Landing on Uneven Grounds of VTOL UAVs in the Context of Lightweight and Fast Adaptations

Nächster Artikel The Developed Conservation Element and Solution Element Method in Two-Dimensional Spherical Coordinate and Its Application to the Analysis of Non-Fourier Heat Conduction

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Gautam, R.; Kumar, S.: Performance and combustion analysis of diesel and tallow biodiesel in CI engine. Energy Rep. 6, 2785–2793 (2020). https://doi.org/10.1016/j.egyr.2020.09.039CrossRef

Öztürk, E.; Can, Ö.; Usta, N.; Yücesu, H.S.: Effects of retarded fuel injection timing on combustion and emissions of a diesel engine fueled with canola biodiesel. Eng. Sci. Technol. an Int. J. 23(6), 1466–1475 (2020). https://doi.org/10.1016/j.jestch.2020.06.008CrossRef

Aydın, S.: Comprehensive analysis of combustion, performance and emissions of power generator diesel engine fueled with different source of biodiesel blends. Energy 205, 118074 (2020). https://doi.org/10.1016/j.energy.2020.118074CrossRef

Singh, D., et al.: A comprehensive review of biodiesel production from waste cooking oil and its use as fuel in compression ignition engines: 3rd generation cleaner feedstock. J. Clean. Prod. 307, 127299 (2021). https://doi.org/10.1016/j.jclepro.2021.127299CrossRef

Goga, G.; Chauhan, B.S.; Mahla, S.K.; Cho, H.M.: Performance and emission characteristics of diesel engine fueled with rice bran biodiesel and n-butanol. Energy Rep. 5, 78–83 (2019). https://doi.org/10.1016/j.egyr.2018.12.002CrossRef

Saravanan, A.; Murugan, M.; Sreenivasa Reddy, M.; Parida, S.: Performance and emission characteristics of variable compression ratio CI engine fueled with dual biodiesel blends of Rapeseed and Mahua. Fuel 263, 116751 (2020). https://doi.org/10.1016/j.fuel.2019.116751CrossRef

Sajjadi, B.; Raman, A.A.A.; Arandiyan, H.: A comprehensive review on properties of edible and non-edible vegetable oil-based biodiesel: composition, specifications and prediction models. Renew. Sustain. Energy Rev. 63, 62–92 (2016). https://doi.org/10.1016/j.rser.2016.05.035CrossRef

Singh, N.; Kaushal, R.; Saluja, R.K.: Storage stability analysis of biodiesel prepared from jatropha oil. J. Adv. Res. Dyn. Control Syst. 31(2), 184–190 (2019)

Saxena, V.; Kumar, N.; Saxena, V.K.: Combustion, performance and emissions of Acacia concinna biodiesel blends in a diesel engine with variable specific heat ratio. J. Therm. Anal. Calorim. 147(2), 1281–1298 (2022). https://doi.org/10.1007/s10973-020-10483-7CrossRef

10.

Saxena, V.; Kumar, N.; Saxena, V.K.: RSMDFA computation approach for optimization and modeling of CI engine performance and emission characteristics fuelled with preheated fuel blend modified withTiO₂ nanomaterial. Mater. Today Proc. 38, 350–358 (2021)CrossRef

11.

Gavhane, R.S., et al.: Effect of zinc oxide nano-additives and soybean biodiesel at varying loads and compression ratios on VCR diesel engine characteristics. Symmetry (Basel) 12(6), 1042 (2020). https://doi.org/10.3390/sym12061042CrossRef

12.

Rajendran, S.: Effect of antioxidant additives on oxides of nitrogen (NOx) emission reduction from Annona biodiesel operated diesel engine. Renew. Energy 148, 1321–1326 (2020). https://doi.org/10.1016/j.renene.2019.10.104CrossRef

13.

Ashok, B., et al.: Multi-functional fuel additive as a combustion catalyst for diesel and biodiesel in CI engine characteristics. Fuel 278, 118250 (2020). https://doi.org/10.1016/j.fuel.2020.118250CrossRef

14.

Mehregan, M.; Moghiman, M.: Experimental investigation of the distinct effects of nanoparticles addition and urea-SCR after-treatment system on NOx emissions in a blended-biodiesel fueled internal combustion engine. Fuel 262, 116609 (2020). https://doi.org/10.1016/j.fuel.2019.116609CrossRef

15.

Prabu, A.; Premkumar, I.J.I.; Pradeep, A.: An assessment on the nanoparticles-dispersed aloe vera biodiesel blends on the Performance, combustion and emission characteristics of a DI diesel engine. Arab. J. Sci. Eng. 44(9), 7457–7463 (2019). https://doi.org/10.1007/s13369-019-03781-2CrossRef

16.

Prabu, A.: Nanoparticles as additive in biodiesel on the working characteristics of a DI diesel engine. Ain Shams Eng. J. 9(4), 2343–2349 (2018). https://doi.org/10.1016/j.asej.2017.04.004CrossRef

17.

Saxena, V.; Kumar, N.; Saxena, V.K.: Investigations on the tribological characteristics of TiO₂-doped nanofluid fuel (biodiesel/diesel blend) at different contact parameters. J. Energy Resour. Technol. (2021). https://doi.org/10.1115/1.4049739CrossRef

18.

Jasrotia A, Shukla AK, and Kumar N (2020) Impact of nanoparticles on the performance and emissions of diesel engine using mahua biodiesel. In: Yadav S, Singh DB, Arora PK, and Kumar H (eds) Proceedings of international conference in mechanical and energy technology: ICMET 2019, India, Singapore, Springer, pp 49–59. doi: https://doi.org/10.1007/978-981-15-2647-3_5.

19.

Venu, H.; Appavu, P.: Al₂O₃ nano additives blended Polanga biodiesel as a potential alternative fuel for existing unmodified DI diesel engine”. Fuel 279, 118518 (2020). https://doi.org/10.1016/j.fuel.2020.118518CrossRef

20.

Kumar, S.; Dinesha, P.; Ajay, C.M.; Kabbur, P.: Combined effect of oxygenated liquid and metal oxide nanoparticle fuel additives on the combustion characteristics of a biodiesel engine operated with higher blend percentages. Energy 197, 117194 (2020). https://doi.org/10.1016/j.energy.2020.117194CrossRef

21.

Rastogi, P.M.; Sharma, A.; Kumar, N.: Effect of CuO nanoparticles concentration on the performance and emission characteristics of the diesel engine running on jojoba (Simmondsia Chinensis) biodiesel. Fuel 286, 119358 (2021). https://doi.org/10.1016/j.fuel.2020.119358CrossRef

22.

Jayaraman, J.; ulIslamLaskar, I.; Dey, K.; Arunkumar, T.; Appavu, P.; Joy, N.: Investigation on titanium oxide nano particles as additives for operating biodiesel fuelled engine. Mater. Today Proc. 44, 3525–3529 (2021). https://doi.org/10.1016/j.matpr.2020.09.291CrossRef

23.

Vale, G.; Mehennaoui, K.; Cambier, S.; Libralato, G.; Jomini, S.; Domingos, R.F.: Manufactured nanoparticles in the aquatic environment-biochemical responses on freshwater organisms: a critical overview. Aquat. Toxicol. 170, 162–174 (2016). https://doi.org/10.1016/j.aquatox.2015.11.019CrossRef

24.

Yu, S.; Liu, J.; Yin, Y.; Shen, M.: Interactions between engineered nanoparticles and dissolved organic matter: a review on mechanisms and environmental effects. J. Environ. Sci. 63, 198–217 (2018). https://doi.org/10.1016/j.jes.2017.06.021CrossRef

25.

Ahamed, M.; Ali, D.; Alhadlaq, H.A.; Akhtar, M.J.: Nickel oxide nanoparticles exert cytotoxicity via oxidative stress and induce apoptotic response in human liver cells (HepG2). Chemosphere 93(10), 2514–2522 (2013). https://doi.org/10.1016/j.chemosphere.2013.09.047CrossRef

26.

Hosseinzadeh-Bandbafha, H., et al.: Carbon quantum dots and their applications. Chem. Soc. Rev. 44(1), 362–381 (2015). https://doi.org/10.1039/c4cs00269eCrossRef

27.

Rani, U.A.; Ng, L.Y.; Ng, C.Y.; Mahmoudi, E.: A review of carbon quantum dots and their applications in wastewater treatment”. Adv. Colloid Interface Sci. 278, 102124 (2020). https://doi.org/10.1016/j.cis.2020.102124CrossRef

28.

Tyagi, A.; Tripathi, K.M.; Singh, N.; Choudhary, S.; Gupta, R.K.: Green synthesis of carbon quantum dots from lemon peel waste: applications in sensing and photocatalysis. RSC Adv. 6(76), 72423–72432 (2016). https://doi.org/10.1039/C6RA10488FCrossRef

29.

Qin, X.; Lu, W.; Asiri, A.M.; Al-Youbi, A.O.; Sun, X.: Green{,} low-cost synthesis of photoluminescent carbon dots by hydrothermal treatment of willow bark and their application as an effective photocatalyst for fabricating Au nanoparticles–reduced graphene oxide nanocomposites for glucose detection. Catal. Sci. Technol. 3(4), 1027–1035 (2013). https://doi.org/10.1039/C2CY20635HCrossRef

30.

Zhou, J.; Sheng, Z.; Han, H.; Zou, M.; Li, C.: Facile synthesis of fluorescent carbon dots using watermelon peel as a carbon source. Mater. Lett. 66(1), 222–224 (2012). https://doi.org/10.1016/j.matlet.2011.08.081CrossRef

31.

Wu, X.; Tian, F.; Wang, W.; Chen, J.; Wu, M.; Zhao, J.X.: Fabrication of highly fluorescent graphene quantum dots using l-glutamic acid for in vitro/in vivo imaging and sensing. J. Mater. Chem. C 1(31), 4676–4684 (2013). https://doi.org/10.1039/C3TC30820KCrossRef

32.

Dong, Y.; Li, G.; Zhou, N.; Wang, R.; Chi, Y.; Chen, G.: Graphene quantum dot as a green and facile sensor for free chlorine in drinking water. Anal. Chem. 84(19), 8378–8382 (2012). https://doi.org/10.1021/ac301945zCrossRef

33.

Wong, Y.K.; Yung, K.K.L.; Tsang, Y.F.; Xia, Y.; Wang, L.; Ho, K.C.: Scenedesmus quadricauda for nutrient removal and lipid production in wastewater. Water Environ. Res. 87(12), 1–9 (2015). https://doi.org/10.2175/WERD1400221.1CrossRef

34.

Koc, A.B.; Abdullah, M.: Performance and NOx emissions of a diesel engine fueled with biodiesel-diesel-water nanoemulsions. Fuel Process. Technol. 109, 70–77 (2013). https://doi.org/10.1016/j.fuproc.2012.09.039CrossRef

35.

Zhu, Y.-J.; Chen, F.: Microwave-assisted preparation of inorganic nanostructures in liquid phase. Chem. Rev. 114(12), 6462–6555 (2014). https://doi.org/10.1021/cr400366sCrossRef

36.

Azam, N.; Najabat Ali, M.; Javaid Khan, T.: Carbon quantum dots for biomedical applications: review and analysis. Mater Front (2021). https://doi.org/10.3389/fmats.2021.700403CrossRef

37.

Ettefaghi, E., et al.: Bio-nano emulsion fuel based on graphene quantum dot nanoparticles for reducing energy consumption and pollutants emission. Energy 218, 119551 (2021). https://doi.org/10.1016/j.energy.2020.119551CrossRef

38.

Hosseinzadeh-Bandbafha, H., et al.: Effects of aqueous carbon nanoparticles as a novel nanoadditive in water-emulsified diesel/biodiesel blends on performance and emissions parameters of a diesel engine. Energy Convers. Manag. 196, 1153–1166 (2019). https://doi.org/10.1016/j.enconman.2019.06.077CrossRef

39.

Balasubramanian, D.; Papla Venugopal, I.; Viswanathan, K.: Characteristics investigation on di diesel engine with nano-particles as an additive in lemon grass oil. SAE Tech Pap (2019). https://doi.org/10.4271/2019-28-0081CrossRef

40.

Attia, A.M.A.; El-Seesy, A.I.; El-Batsh, H.M.; Shehata, M.S.: Effects of alumina nanoparticles additives into jojoba methyl ester-diesel mixture on diesel engine performance. Energy (2017). https://doi.org/10.1115/IMECE2014-39988CrossRef

41.

Venu, H.; Madhavan, V.: Effect of Al₂O₃ nanoparticles in biodiesel-diesel-ethanol blends at various injection strategies: performance, combustion and emission characteristics. Fuel 186, 176–189 (2016). https://doi.org/10.1016/j.fuel.2016.08.046CrossRef

42.

Kumar, A.M.; Kannan, M.; Nataraj, G.: A study on performance, emission and combustion characteristics of diesel engine powered by nano-emulsion of waste orange peel oil biodiesel. Renew. Energy 146, 1781–1795 (2020). https://doi.org/10.1016/j.renene.2019.06.168CrossRef

43.

Nanthagopal, K.; Ashok, B.; Tamilarasu, A.; Johny, A.; Mohan, A.: Influence on the effect of zinc oxide and titanium dioxide nanoparticles as an additive with Calophyllum inophyllum methyl ester in a CI engine. Energy Convers. Manag. 146, 8–19 (2017). https://doi.org/10.1016/j.enconman.2017.05.021CrossRef

44.

Gharehghani, A.; Asiaei, S.; Khalife, E.; Najafi, B.; Tabatabaei, M.: Simultaneous reduction of CO and NOx emissions as well as fuel consumption by using water and nano particles in Diesel-Biodiesel blend. J. Clean. Prod. 210, 1164–1170 (2019). https://doi.org/10.1016/j.jclepro.2018.10.338CrossRef

45.

Karthikeyan, S.; Elango, A.; Prathima, A.: An environmental effect of GSO methyl ester with ZnO additive fuelled marine engine. Indian J. Geo-Marine Sci. 43(4), 564–570 (2014)

46.

Soudagar, M.E.M., et al.: An investigation on the influence of aluminium oxide nano-additive and honge oil methyl ester on engine performance, combustion and emission characteristics. Renew. Energy 146, 2291–2307 (2020). https://doi.org/10.1016/j.renene.2019.08.025CrossRef

47.

Soudagar, M.E.M.; Nik-Ghazali, N.N.; Abul Kalam, M.; Badruddin, I.A.; Banapurmath, N.R.; Akram, N.: The effect of nano-additives in diesel-biodiesel fuel blends: a comprehensive review on stability, engine performance and emission characteristics. Energy Convers. Manag. 178(10), 146–177 (2018). https://doi.org/10.1016/j.enconman.2018.10.019CrossRef

48.

Nedayali, A.; Shirneshan, A.: Experimental study of the effects of biodiesel on the performance of a diesel power generator. Energy I & Environ. 27(5), 553–565 (2016). https://doi.org/10.1177/0958305X15627550CrossRef

49.

Karthikeyan, T.: Effects of copper oxide nanoparticle addition in diesel and biodiesel blends on the performance and emission characteristics of a diesel engine. Int. J. Res. Appl. Sci. Eng. Technol. 7, 156–161 (2019). https://doi.org/10.22214/ijraset.2019.4028CrossRef

50.

Tamilvanan, A.; Balamurugan, K.; Vijayakumar, M.: Effects of nano-copper additive on performance, combustion and emission characteristics of Calophyllum inophyllum biodiesel in CI engine. J. Therm. Anal. Calorim. 136(1), 317–330 (2019). https://doi.org/10.1007/s10973-018-7743-4CrossRef

51.

D’Silva, R., et al.: Effect of copperoxide nanoadditives on the performance and emissions characteristics of a CI engine. Energy and Power 7(4), 99–104 (2017)MathSciNet

52.

Perumal, V.; Ilangkumaran, M.: The influence of copper oxide nano particle added pongamia methyl ester biodiesel on the performance, combustion and emission of a diesel engine. Fuel 232(March), 791–802 (2018). https://doi.org/10.1016/j.fuel.2018.04.129CrossRef

53.

Kalaimurugan, K.; Karthikeyan, S.; Periyasamy, M.; Dharmaprabhakaran, T.: Combustion analysis of CuO₂ nanoparticles addition with neochloris oleoabundans algae biodiesel on CI engine. Mater. Today Proc. 33, 2573–2576 (2020). https://doi.org/10.1016/j.matpr.2019.12.152CrossRef

54.

Sadhik Basha, J.; Anand, R.B.: Performance, emission and combustion characteristics of a diesel engine using carbon nanotubes blended jatropha methyl ester emulsions. Alexandria Eng. J. 53(2), 259–273 (2014). https://doi.org/10.1016/j.aej.2014.04.001CrossRef

55.

Mirzajanzadeh, M., et al.: A novel soluble nano-catalysts in diesel–biodiesel fuel blends to improve diesel engines performance and reduce exhaust emissions. Fuel 139, 374–382 (2015). https://doi.org/10.1016/j.fuel.2014.09.008CrossRef

56.

El-Seesy, A.I.; Abdel-Rahman, A.K.; Bady, M.; Ookawara, S.: Performance, combustion, and emission characteristics of a diesel engine fueled by biodiesel-diesel mixtures with multi-walled carbon nanotubes additives. Energy Convers. Manag. 135, 373–393 (2017). https://doi.org/10.1016/j.enconman.2016.12.090CrossRef

57.

Hoseini, S.S.; Najafi, G.; Ghobadian, B.; Mamat, R.; Ebadi, M.T.; Yusaf, T.: Novel environmentally friendly fuel: the effects of nanographene oxide additives on the performance and emission characteristics of diesel engines fuelled with Ailanthus altissima biodiesel. Renew. Energy 125, 283–294 (2018). https://doi.org/10.1016/j.renene.2018.02.104CrossRef

58.

EL-Seesy, A.L.; Abdel-Rahman, A.K.; Bady, M.; Ookawara, S.: The influence of multi-walled carbon nanotubes additives into non-edible biodiesel-diesel fuel blend on diesel engine performance and emissions. Energy Procedia 100, 166–172 (2016). https://doi.org/10.1016/j.egypro.2016.10.160CrossRef

59.

El-Seesy, A.I.; Hassan, H.; Ookawara, S.: Effects of graphene nanoplatelet addition to jatropha biodiesel-diesel mixture on the performance and emission characteristics of a diesel engine. Energy 147, 1129–1152 (2018). https://doi.org/10.1016/j.energy.2018.01.108CrossRef

60.

Paramashivaiah, B.M.; Banapurmath, N.R.; Rajashekhar, C.R.; Khandal, S.V.: Studies on effect of graphene nanoparticles addition in different levels with simarouba biodiesel and diesel blends on performance, combustion and emission characteristics of CI engine. Arab. J. Sci. Eng. 43(9), 4793–4801 (2018). https://doi.org/10.1007/s13369-018-3121-6CrossRef

61.

El-Seesy, A.I.; Hassan, H.; Ookawara, S.: Performance, combustion, and emission characteristics of a diesel engine fueled with Jatropha methyl ester and graphene oxide additives. Energy Convers. Manag. 166(4), 674–686 (2018). https://doi.org/10.1016/j.enconman.2018.04.049CrossRef

62.

Soudagar, M.E.M., et al.: The effects of graphene oxide nanoparticle additive stably dispersed in dairy scum oil biodiesel-diesel fuel blend on CI engine: performance, emission and combustion characteristics. Fuel 257, 116015 (2019). https://doi.org/10.1016/j.fuel.2019.116015CrossRef

63.

Debbarma, S.; Misra, R.D.; Das, B.: Performance of graphene-added palm biodiesel in a diesel engine. Clean Technol. Environ. Policy 22(2), 523–534 (2020). https://doi.org/10.1007/s10098-019-01800-2CrossRef

64.

Hoseini, S.S.; Najafi, G.; Ghobadian, B.; Ebadi, M.T.; Mamat, R.; Yusaf, T.: Biodiesels from three feedstock: The effect of graphene oxide (GO) nanoparticles diesel engine parameters fuelled with biodiesel. Renew. Energy 145, 190–201 (2020). https://doi.org/10.1016/j.renene.2019.06.020CrossRef

65.

Ettefaghi, E., et al.: A novel bio-nano emulsion fuel based on biodegradable nanoparticles to improve diesel engines performance and reduce exhaust emissions. Renew. Energy 125, 64–72 (2018). https://doi.org/10.1016/j.renene.2018.01.086CrossRef

66.

Ayhan, V., et al.: Optimization of the factors affecting performance and emissions in a diesel engine using biodiesel and EGR with Taguchi method. Fuel 261(May), 2020 (2019). https://doi.org/10.1016/j.fuel.2019.116371CrossRef

67.

Agrawal, T.; Gautam, R.; Agrawal, S.; Singh, V.; Kumar, M.; Kumar, S.: Optimization of engine performance parameters and exhaust emissions in compression ignition engine fueled with biodiesel-alcohol blends using taguchi method, multiple regression and artificial neural network. Sustain. Futur. 2, 100039 (2020). https://doi.org/10.1016/j.sftr.2020.100039CrossRef

68.

Yadav, P.; Sharma, P.; Singh, N.: Fabrication of a punching die using P-20 material on wire electric discharge machine by Taguchi method. Int. J. Sci. Eng. Res. 5(1), 525–534 (2014)

69.

Sagar, Ȧ, et al.: Effect of tool on tensile strength in single and double sided friction stir welding. Int. J. Sci. Eng. Res. 4(11), 1–6 (2014)

70.

Miraculas, G.A.; Bose, N.: Effect of compression ratio on diesel engine performance and emission fueled with tamanu oil methyl ester and its blends. Adv. Mater. Res. 984, 850–854 (2014)CrossRef

71.

Effendy, M.; Surono, A.; Saputra, E.; Nugraha, N.A.: Performance and smoke opacity of compression-ignition engine using used-waste oil. Case Stud. Therm. Eng. 26, 101063 (2021). https://doi.org/10.1016/j.csite.2021.101063CrossRef

72.

Datta Bharadwaz, Y.; Govinda Rao, B.; Dharma Rao, V.; Anusha, C.: Improvement of biodiesel methanol blends performance in a variable compression ratio engine using response surface methodology. Alex. Eng. J. 55(2), 1201–1209 (2016). https://doi.org/10.1016/j.aej.2016.04.006CrossRef

73.

Shaafi, T.; Velraj, R.: Influence of alumina nanoparticles, ethanol and isopropanol blend as additive with diesel–soybean biodiesel blend fuel: Combustion, engine performance and emissions. Renew. Energy 80, 655–663 (2015). https://doi.org/10.1016/j.renene.2015.02.042CrossRef

74.

Karmakar, B.; Ghosh, B.; Samanta, S.; Halder, G.: Sulfonated catalytic esterification of Madhuca indica oil using waste Delonix regia: L16 Taguchi optimization and kinetics”. Sustain. Energy Technol. Assessments 37, 100568 (2020). https://doi.org/10.1016/j.seta.2019.100568CrossRef

Titel: Optimization of Engine Parameters Using Taguchi Technique for a Diesel Engine Running on a Newly Developed bio-nano Diesel Emulsion
verfasst von: Narender Singh
Rajneesh Kaushal
Publikationsdatum: 28.03.2023
Verlag: Springer Berlin Heidelberg
Erschienen in: Arabian Journal for Science and Engineering / Ausgabe 9/2023
Print ISSN: 2193-567X
Elektronische ISSN: 2191-4281
DOI: https://doi.org/10.1007/s13369-023-07808-7

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 9/2023

Improved Proximity Indexed Value MCDM Method for Solving the Rank Reversal Problem: A Simulation-Based Approach

Boundary Heat Flux Estimation for Natural Convection in a Square Enclosure Containing a Cylinder: An Inverse Approach

Cost Optimization of Heat Exchanger Inventory in Cascade Refrigeration Cycles

Tri-Rotor Propeller Design Concept, Optimization and Analysis of the Lift Efficiency During Hovering

Improving the Cooling Performance in a Low Reynolds Duct Flow of Multiple Impinging Jets with Non-uniform Spacing and Unequal Diameters of Nozzles

A Multiphysics Sealing Mechanism Model of Rotary Lip Seals under Mixed Lubricating Conditions Considering the Effects of the Meniscus

Premium Partner

Marktübersichten