nach oben

Erschienen in:

2020 | OriginalPaper | Buchkapitel

Review on Surface Modifications of the Workpiece by Electric Discharge Machining

verfasst von : Vipin Handa, Parveen Goyal, Rajesh Kumar

Erschienen in: Advances in Materials Processing

Verlag: Springer Singapore

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The recent times have seen an expanding enthusiasm for the novel uses of electrical discharge machining (EDM) method, with specific accentuation on the capability of this procedure for surface modification. Other than the disintegration of work material amid machining, the inborn idea of the procedure results in the expulsion of tool material too. Through either dispersing metallic powders in the dielectric or by utilizing composite or both intentional material exchanges might be done under explicit machining conditions. In this review paper, secondary use of EDM is discussed which has revolutionized the concept of surface modification. A review of the wonder of surface adjustment by EDM and future potential applications has been presented in this paper.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Vorheriges Kapitel Plasma Spray Deposition of HA–TiO2 Composite Coating on Ti–6Al–4V Alloy for Orthopedic Applications

Nächstes Kapitel Experimental Investigations on Heat Generation and Surface Roughness During Orthogonal Machining of Stainless Steel Using Bio-based Oil MQL

Chen, S.L., Yan, B.H., Huang, F.Y.: Influence of kerosene and distilled water as dielectrics on the electric discharge machining characteristics of Ti–6A1–4V. J. Mater. Process. Technol. 87(1–3), 107–111 (1999)CrossRef

Abu Zeid, O.A.: On the effect of electro discharge machining parameters on the fatigue life of AISI D6 tool steel. J. Mater. Process. 68(1), 27–32 (1997)CrossRef

Leuven, K.U., Integrity, S.: Study of the white layer of a surface machined by die-sinking electro-discharge machining. 44(1), 169–172 (1995)

Tan, P.C., Yeo, S.H.: Investigation of recast layers generated by a powder-mixed dielectric micro electrical discharge machining process. Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. 225(7), 1051–1062 (2011)

Simao, J., Lee, H., Aspinwall, D., Dewes, R., Aspinwall, E.: Workpiece surface modification using electrical discharge machining. Int. J. Mach. Tools Manuf. 43(2), 121–128 (2003)CrossRef

Chen, Y.F., Lin, Y.C.: Surface modifications of Al–Zn–Mg alloy using combined EDM with ultrasonic machining and addition of TiC particles into the dielectric. J. Mater. Process. Technol. 209(9), 4343–4350 (2009)CrossRef

Aspinwall, D., El-menshawy, F., Meadows, K., Sima, J.: Surface alloying using PM composite electrode materials when electrical discharge texturing hardened AISI D2. J. Mater. Process. Technol. 127, 211–216 (2002)CrossRef

Prakash, C., Kansal, H.K., Pabla, B.S., Puri, S., Aggarwal, A.: Electric discharge machining: a potential choice for surface modification of metallic implants for orthopedic applications: a review. Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. 230(2), 331–353 (2016)

Kumar, S., Batra, U.: Surface modification of die steel materials by EDM method using tungsten powder-mixed dielectric. J. Manuf. Process. 14(1), 35–40 (2012)CrossRef

10.

Furutani, K., Saneto, A., Takezawa, H., Mohri, N., Miyake, H.: Accretion of titanium carbide by electrical discharge machining with powder suspended in working fluid. Precis. Eng. 25, 138–144 (2001)CrossRef

11.

Gangadhar, A., Shunmugam, M.S., Philip, P.K.: Surface modification in electro discharge processing with a powder compact tool electrode. Wear 143(1), 45–55 (1991)CrossRef

12.

Lin, Y.C., Yan, B.H., Huang, F.Y.: Surface improvement using a combination of electrical discharge machining with ball burnish machining based on the Taguchi method. Int. J. Adv. Manuf. Technol. 18, 673–682 (2001)CrossRef

13.

Marafona, J., Wykes, C.: New method of optimizing material removal rate using EDM with copper-tungsten electrodes. Int. J. Mach. Tools Manuf. 40(2), 153–164 (2000)CrossRef

14.

Mohri, N., Saito, N., Tsunekawa, Y., Technological, T., Kinoshita, N.: Metal surface modification by electrical discharge machining with composite electrode. CIRP Ann. 42(1), 219–222 (1993)CrossRef

15.

Tsai, H.C., Yan, B.H., Huang, F.Y.: EDM performance of Cr/Cu-based composite electrodes. Int. J. Mach. Tools Manuf. 43(3), 245–252 (2003)CrossRef

16.

Tsunekawa, Y., Okumiya, M., Mohri, N.: Surface modification of aluminum by electrical discharge alloying. Mater. Sci. Eng. A 174, 193–198 (1994)CrossRef

17.

Yan, B.H., Tsai, H.C., Huang, F.Y.: The effect in EDM of a dielectric of a urea solution in water on modifying the surface of titanium. Int. J. Mach. Tools Manuf. 45(2), 194–200 (2005)CrossRef

18.

Zhang, Y., Liu, Y., Ji, R., Cai, B.: Study of the recast layer of a surface machined by sinking electrical discharge machining using water-in-oil emulsion as dielectric. Appl. Surf. Sci. 257(14), 5989–5997 (2011)CrossRef

19.

Kumar, S., Singh, R., Singh, T.P., Sethi, B.L.: Surface modification by electrical discharge machining: a review. J. Mater. Process. Technol. 209(8), 3675–3687 (2009)CrossRef

20.

Hirao, A., Tani, T., Gotoh, H., Aoshima, S., Mohri, N.: Study of deposition machining using electrical discharge with reciprocating rotation in air gap. Int. J. Electr. Mach. 21, 2–7 (2016)

21.

Kuo, C., Kao, H., Wang, H.: Novel design and characterization of surface modification in wire electrical discharge machining using assisting electrodes. J. Mater. Process. Tech. 244, 136–149 (2017)CrossRef

22.

Batish, A., Bhattacharya, A.: Mechanism of material deposition from powder, electrode and dielectric for surface modification of H11 and H13 die steels in EDM process. Mater. Sci. Forum 701, 61–75 (2011)CrossRef

23.

Bains, P.S., Sidhu, S.S., Payal, H.S., Kaur, S.: Magnetic field influence on surface modifications in powder mixed EDM. Silicon 11(1), 415–423 (2019)CrossRef

24.

Chen, S.L., Lin, M.H., Huang, G.X., Wang, C.C.: Research of the recast layer on implant surface modified by micro-current electrical discharge machining using deionized water mixed with titanium powder as dielectric solvent. Appl. Surf. Sci. 311, 47–53 (2014)CrossRef

25.

Trauth, D., Klocke, F., Welling, D., Terhorst, M., Mattfeld, P., Klink, A.: Investigation of the surface integrity and fatigue strength of Inconel 718 after wire EDM and machine hammer peening. Int. J. Mater. Form. 9(5), 635–651 (2016)CrossRef

26.

Mohanty, S., Kumar, V., Tyagi, R., Kumar, S., Bhushan, B., Das, A.K., Dixit, A.R.: Surface alloying using tungsten disulphide powder mixed in dielectric in micro-EDM on Ti–6Al–4V. IOP Conf. Ser. Mater. Sci. Eng. 377(1), 012040 (2018)CrossRef

27.

Gill, A.S., Kumar, S.: Surface alloying of H11 die steel by tungsten using EDM process. Int. J. Adv. Manuf. Technol. 78 (9–12), 1585–1593 (2015)

28.

Goyal, P., Suri, N.M., Kumar, S., Kumar, R.: Investigating the surface properties of EN-31 die-steel after machining with powder metallurgy EDM electrodes. Mater. Today: Proc. 4(2), 3694–3700 (2017)

29.

Goyal, P., Kumar, S., Kumar, R.: Effect of high chromium platinum steel with composite copper-tin material electrode on electric discharge machining performance. Mater. Today: Proc. 5(14), 27726–27731 (2018)

30.

Antil, P., Singh, S., Singh, S., Prakash, C., Pruncu, C.: Metaheuristic approach in machinability evaluation of SiCp/glass fiber reinforced PMCs during electrochemical discharge machining process. Meas Control (2019)

31.

Basak, A., Pramanik, A., Prakash, C.: Surface, kerf width and material removal rate of Ti–6Al–4V titanium alloy generated by wire electrical discharge machining. Heliyon 5(4), 01473 (2019)

32.

Prakash, C., Singh, S., Pruncu, C.I., Mishra, V., Królczyk, G., Pimenov, D.Y., Pramanik, A.: Surface modification of Ti–6Al–4V alloy by electrical discharge coating process using partially sintered Ti–Nb electrode. Materials 12(7), 1006 (2019)CrossRef

33.

Prakash, C., Singh, S., Pabla, B.S.: Multi-objective optimization of EDM parameters to deposit HA-containing coating on Mg-Zn-Mn alloy using particle swarm optimization. Vacuum 158, 180–190 (2018)CrossRef

34.

Prakash, C., Singh, S., Pabla, B.S., Uddin, M.S.: Synthesis, characterization, corrosion and bioactivity investigation of nano-HA coating deposited on biodegradable Mg-Zn–Mn alloy. Surf. Coat. Technol. 346, 9–18 (2018)CrossRef

35.

Prakash, C., Uddin, M.S.: Surface modification of β-phase Ti implant by hydroxyapatite mixed electric discharge machining to enhance the corrosion resistance and in-vitro bioactivity. Surf. Coat. Technol. 236, 134–145 (2017)CrossRef

36.

Aliyu, A.A., Abdul-Rani, A.M., Ginta, T.L., Prakash, C., Axinte, E., Razak, M.A., Ali, S.: A review of additive-mixed electric discharge machining: current status and future perspectives for surface modification of biomedical implants. Adv. Mater. Sci. Eng. (2017)

37.

Aliyu, A.A., Abdul-Rani, A.M., Ginta, T.L., Prakash, C., Axinte, E., Fua-Nizan, R.: Fabrication of nanoporosities on metallic glass surface by hydroxyapatite mixed EDM for orthopedic application. Accepted in Malaysian J. Fundam. Appl. Sci. (2017)

38.

Prakash, C., Kansal, H.K., Pabla, B.S., Puri, S., Aggarwal, A.: Electric discharge machining—a potential choice for surface modification of metallic implants for orthopedic applications: a review. Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. 230(2), 231–253 (2016)

39.

Prakash, C., Kansal, H.K., Pabla, B.S., Puri, S.: Processing and characterization of novel biomimetic nanoporous bioceramic surface on β-Ti implant by powder mixed electric discharge machining. J. Mater. Eng. Perform. 24, 3622–3633 (2015)CrossRef

40.

Prakash, C., Kansal, H.K., Pabla, B.S., Puri, S.: Experimental investigations in powder mixed electrical discharge machining of Ti–35Nb–7Ta–5Zr β-Ti alloy. Mater. Manuf. Process 32(3), 274–285 (2017)CrossRef

41.

Prakash, C., Kansal, H.K., Pabla, B.S., Puri, S.: Effect of surface nano-porosities fabricated by powder mixed electric discharge machining on bone-implant interface: an experimental and finite element study. Nanosci. Nanotechnol. Lett. 8(10), 815–826 (2016)CrossRef

42.

Prakash, C., Kansal, H.K., Pabla, B.S., Puri, S.: Multi-objective optimization of powder mixed electric discharge machining parameters for fabrication of biocompatible layer on β-Ti alloy using NSGA-II coupled with Taguchi based response surface methodology. J. Mech. Sci. Technol. 30(9), 4195–4204 (2016)

43.

Prakash, C., Kansal, H.K., Pabla, B.S., Puri, S.: Powder mixed electric discharge machining an innovative surface modification technique to enhance fatigue performance and bioactivity of β-Ti implant for orthopaedics application. J. Comput. Inf. Sci. Eng. 14(4), 1–9 (2016)

44.

Prakash, C., Kansal, H.K., Pabla, B.S., Puri, S.: Potential of powder mixed electric discharge machining to enhance the wear and tribological performance of β-Ti implant for orthopedic applications. J. Nanoeng. Nanomanufa. 5(4), 261–269 (2015)CrossRef

45.

Beri, N., Maheshwari, S., Sharma, C., Kumar, A.: Technological advancement in electrical discharge machining with powder metallurgy processed electrodes: a review. Mater. Manuf. Process. 25(10), 1186–1197 (2010)CrossRef

46.

Lauwers, B., Kruth, J.P., Liu, W., Eeraerts, W., Schacht, B., Bleys, P.: Investigation of material removal mechanisms in EDM of composite ceramic materials. J. Mater. Process. Technol. 149(1–3), 347–352 (2004)CrossRef

Titel: Review on Surface Modifications of the Workpiece by Electric Discharge Machining
verfasst von: Vipin Handa
Parveen Goyal
Rajesh Kumar
Verlag: Springer Singapore
Buch: Advances in Materials Processing
Print ISBN: 978-981-15-4747-8

Electronic ISBN: 978-981-15-4748-5

Copyright-Jahr: 2020
DOI: https://doi.org/10.1007/978-981-15-4748-5_3

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht