Ausgabe 9-10/2018
Inhalt (32 Artikel)
Computer Simulation of Piercing in a Four-High Screw Rolling Mill
B. A. Romantsev, M. M. Skripalenko, Tran Ba Huy, M. N. Skripalenko, Yu. A. Gladkov, A. A. Gartvig
Effect of the Thermal Insulation of the Inner Wall on the Thermal Condition of the Air Tuyeres of Blast Furnaces
Yu. S. Tarasov, A. G. Radyuk, S. M. Gorbatyuk
Effect of Ferrite Content on High-Temperature Strength of 12% Chromium Steels with a Ferritic-Martensitic Structure
M. Yu. Belomytsev, S. M. Obraztsov, A. V. Molyarov
Manufacture of High-Carbon Ferrochrome Using Anthracite
A. G. Kaliakparov, S. R. Baltabaev, V. M. Strakhov, A. A. Mukhtar
Effect of Chemical Composition and Microstructure Parameters on Carbon and Low-Alloy Steel Corrosion Resistance
I. G. Rodionova, M. V. Feoktistova, O. N. Baklanova, A. V. Amezhnov, D. L. D’yakonov
Heat Treatment Regime Optimization for High-Strength Low-Carbon Steel Forged Slabs
V. V. Tsukanov, V. G Milyuts, O. E. Nigmatulin, S. A. Golosienko, S. V. Efimov, A. G. Pavlova
Development of Technology and Assimilation of Production for Alloy VZh172 Rolled Product
I. V. Kabanov, A. A. Gorbushkin, A. V. Razvorotneva, A. A. Mironov, G. V. Isaeva
Study of the Metal Properties and Structure of a Large Shell Made of 15Kh2MFA Steel
I. V. Teplukhina, V. I. Bogdanov, O. Yu. Zaitseva, E. L. Shamrai, A. S. Tsvetkov
Developing High-Speed Rolling Schedules for Tramrails in Continuous Reversing Train
S. V. Smetanin, V. N. Peretyat’ko
Promising Areas of Chemical and Microbiological Treatment of Nonferrous and Precious Metal Mineral Resources
V. Zh. Arens, L. V. Shumilova, M. I. Fazlullin, G. Kh. Khcheyan
Production Features for Preparing Semifinished Sheet of Hypereutectic Alloys Based on the Aluminum–Cerium System
P. S. Evseev, N. V. Eremeev, A. P. Petrov, A. V. Bespalov, V. V. Eremeev
Preparation of Aluminum–Carbon Nanotubes Composite Material by Hot Pressing
M. P. Kuz’min, N. A. Ivanov, V. V. Kondrat’ev, V. G. Grigor’ev, M. Yu. Kuz’mina, A. I. Begunov, A. S. Kuz’mina, N. N. Ivanchik
Physical Modelling of Hot Rolling for Low-Density Alloy of the Al–Mg–Li–Zr–Zn–Sc System
Ya. A. Erisov, F. V. Grechnikov
Simulation of Continuous Roll Forming Process for Producing Welded Pipes of Small and Medium Diameters
A. P. Kolikov, I. M. Taupek
Analysis of the Blast-Furnace Process at High Smelting Rate
S. V. Filatov, A. V. Lozovich, V. N. Titov, S. A. Zagainov, I. F. Kurunov
Effect of the Precompaction Pressure on the Density Distribution in a Metallurgical Briquette During Roller Pressing
Yu. N. Loginov, N. A. Babailov, L. I. Polyanskii
Metal Evaporation in the Area of an Anode Spot in Plasma and Direct Current Arc Steel Smelting Furnaces
L. M. Simonyan, A. A. Alpatova
Effect of Temperature-Deformation Treatment Regime for Special Alloy Steels on Rolled Product Structural State and Properties
A. V. Koldaev, A. V. Amezhnov, A. I. Zaitsev, A. B. Stepanov
Evaluation Criterion for Forging Ingot Steel Inclination Towards Liquation
A. N. Romashkin, V. S. Dub, D. S. Tolstykh, I. A. Ivanov, A. N. Mal’ginov
Mastering the Production of Blanks for Gas-Turbine Engines and Power Units in the 200 MN Die-Forging Press
S. G. Glushenkova, K. A. Polozhentsev, A. I. Dmitriev, A. Yu. Bogachev, G. Yu. Lukonin, D. S. Penkin
Production of Hollow Railroad Axles by Screw Piercing and Radial Forging
V. P. Romanenko, P. P. Stepanov, S. M. Kriskovich
Complete Evaluation of Extruded Aluminum Section and Semiproduct Mechanical Properties Under Conditions of Typical Regional Manufacturer Altek
E. N. Smirnov, V. A. Sklyar, M. V. Mitrofanov, O. E. Smirnov, V. A. Belevitin, A. N. Smirnov
Radial-Shear Rolling of Titanium Alloy VT-8 Bars with Controlled Structure for Small Diameter Ingots (≤200 mm)
B. V. Karpov, P. V. Patrin, S. P. Galkin, E. A. Kharitonov, I. B. Karpov
Development of Waelz-Oxide Hydrometallurgical Processing Technology with Preparation of Carbonized Lead Cake
S. A. Yakornov, A. M. Pan’shin, P. A. Kozlov, D. A. Ivakin, E. V. Golubeva
Development of a Production Scheme for Processing Rebellious Gold-Containing Flotation Concentrates by Autoclave Oxidation
I. R. Boboev, Sh. Bobozoda, L. S. Strizhko
Selection of Conversion Layer Applied Beneath Thread Lubricant Coating
T. N. Churikova, N. P. Samkova
Sorption Extraction of Vanadium Compounds from Acid Solutions with Finely Divided Modified Aluminosilicate
D. P. Ordinartsev, A. V. Sviridov, S. S. Naboichenko, V. V. Yurchenko
Device for One- and Two-Sided Molding of Refractory Metal Powders Into Electric-Arc Melting Electrode Workpieces
L. A. Barkov, M. N. Samodurova, R. A. Zakirov, Yu. S. Latfulina
Correction to: Creep Deformation of Carbon-Based Cathode Materials for Low-Temperature Aluminum Electrolysis
Wei Wang, Weijie Chen, Wanduo Gu