nach oben

Rheologica Acta

Erschienen in:

01.11.2008 | Original Contribution

Squeeze-flow and vane rheometry of a gas–liquid foam

verfasst von: G. H. Meeten

Erschienen in: Rheologica Acta | Ausgabe 8/2008

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The rheology and slip of a dry shaving foam are investigated using squeeze-flow and rotating-vane methods. Constant-force squeeze flow between planar surfaces is used to study the effect of surface roughness on slip and to obtain the yield stress. Non-slip vane measurements are used to obtain the linear shear viscosity and elasticity at small strains, and the yield stress and strain at large strains. Data are compared with the small-strain Maxwell and Kelvin–Voigt linear-viscoelastic models. An apparent dependence of the yield stress and elasticity on the rotational speed of the vane is shown to result from time-dependent rheological parameters as the foam ages. The effect of viscosity in the pre-yield region may give an erroneous identification of yield.

Vorheriger Artikel Recoverable strains and retardation times of monodisperse suspensions of silicon dioxide spheres in poly(dimethylsiloxane)

Nächster Artikel Rheo-optic flow-induced crystallisation of polypropylene and polyethylene within confined entry–exit flow geometries

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Ak MM, Gunasekaran S (2000) Simulation of lubricated squeezing flow of a Herschel–Bulkley fluid under constant force. Appl Rheol 10:274–279

Alderman NJ, Meeten GH, Sherwood JD (1991) Vane rheometry of bentonite gels. J Non-Newtonian Fluid Mech 39:291–310CrossRef

Alkhagen M, Toll S (2002) A triaxial rheometer for soft compressible solids. J Rheol 46:31–47CrossRef

Anon (1999) Grinding and abrasive processes. In: Stephens JH (ed) Kempe’s Engineers Yearbook for 1999. Miller Freeman, UK, Tonbridge, Kent, pp 949–961

Baravian C, Lalante A, Parker A (2002) Vane rheometry with a large, finite gap. Appl Rheol 12:81–87

Barnes HA, Nguyen QD (2001) Rotating vane rheometry-a review. J Non-Newtonian Fluid Mech 98:1–14CrossRef

Becu L, Grondin P, Colin A, Manneville S (2004) How does a concentrated emulsion flow? Yielding, local rheology, and wall slip. Colloids Surf A 263:146–152CrossRef

Bertola V, Bertrand F, Tabutaeu H, Bonn D, Coussot P (2003) Wall slip and yielding in pasty materials. J Rheol 47:1211–1226CrossRef

Cantat I, Pitois O (2005) Mechanical probing of liquid foam ageing. J Phys Condens Matter 17:S3455–S3461CrossRef

Chaari F, Racineux G, Poitou A, Chaoche M (2003) Rheological behavior of sewage sludge and strain-induced dewatering. Rheol Acta 42:273–279

Chan TW, Baird DG (2002) An evaluation of a squeeze flow rheometer for the rheological characterization of a filled polymer with a yield stress. Rheol Acta 41:245–256CrossRef

Cohen-Addad S, Hohler R, Khidas Y (2004) Origin of the slow linear viscoelastic response of aqueous foams. Phys Rev Lett 93(028302):1–4

Collomb J, Chaari F, Chaouche M (2004) Squeeze flow of concentrated suspensions of spheres in Newtonian and shear-thinning fluids. J Rheol 48:405–416CrossRef

Cox S, Weaire D, Glazier JA (2004) The rheology of two-dimensional foams. Rheol Acta 43:442–448CrossRef

Da Cruz F, Chevoir F, Bonn D, Coussot P (2002) Viscosity bifurcation in granular materials, foams, and emulsions. Phys Rev E 66(051305):1–7

Davis JP, Foegeding EA (2004) Foaming and interfacial properties of polymerized whey protein isolate. J Food Sci 69:C404–C410

Debrégeas G, Tabuteau H, di Meglio J-M (2001) Deformation and flow of a two-dimensional foam under continuous shear. Phys Rev Lett 87(178305):1–4

De Bruyn JR (2006) Age dependence of the drag force in an aqueous foam. Rheol Acta 45:803–811CrossRef

Denkov ND, Tcholakova S, Golemanov K, Subramanian V, Lips A (2006) Foam-wall friction: effect of air volume fraction for tangentially immobile bubble surface. Colloids Surf A 282-283:329–347CrossRef

Dollet B, Durth M, Graner F (2006) Flow of foam past an elliptical obstacle. Phys Rev E 73(061404):1–4

Emile J, Hardy E, Saint-Jalmes A, Terriac E, Delannay R (2007) Swelling of a single foam film under slipping. Colloids Surf A 304:72–76CrossRef

Engmann J, Servais C, Burbidge AS (2005) Squeeze flow theory and applications to rheometry: a review. J Non-Newtonian Fluid Mech 132:1–27CrossRef

Enzendorfer C, Harris RA, Valkó P, Economides MJ, Fokker PA, Davies DD (1995) Pipe rheometry of foams. J Rheol 39:345–358CrossRef

French RJ (1960) Foam viscometer. J Sci Instrum 37:307–308CrossRef

Gardiner BS, Dlugogorski BZ, Jameson GJ, Chhabra RP (1998) Yield stress measurements of aqueous foam in the dry limit. J Rheol 42:1437–1450CrossRef

Gopal AD, Durian DJ (1999) Shear-induced “melting” of an aqueous foam. J Coll Interface Sci 213:169–178CrossRef

Herzhaft B, Kakadjian S, Moan M (2005) Measurement and modeling of the flow behavior of aqueous foams using a recirculating pipe rheometer. Colloids Surf A 263:153–164CrossRef

Höhler R, Cohen-Addad S (2005) Rheology of liquid foam. J Phys Condens Matter 17:R1041–R1069CrossRef

Kabla A, Debrégeas G (2007) Quasi-static rheology of foams. Part 1. Oscillating strain. J Fluid Mech 587:23–44

Kabla A, Scheibert J, Debrégeas G (2007) Quasi-static rheology of foams. Part 2. Continuous shear flow. J Fluid Mech 587:45–72

Kampf N, Martinez CG, Corradini MG, Peleg M (2003) Effect of two gums on the development, rheological properties and stability of egg albumen foams. Rheol Acta 42:259–268

Keentok M (1982) The measurement of the yield stress of liquids. Rheol Acta 21:325–332CrossRef

Khan SA, Schnepper CA, Armstrong RC (1988) Foam rheology: III. Measurement of shear flow properties. J Rheol 32:69–92CrossRef

Kim YD, Dee DD (2008) Measuring static yield stress of electrorheological fluids using the slotted plate device. Rheol Acta 47:105–110CrossRef

Kolenda F, Retana P, Racineux G, Poitou A (2003) Identification of rheological parameters by the squeezing test. Powder Technol 130:56–62CrossRef

Kraynik AM (1990) ER fluid standards: comments on ER fluid rheology. In: Carlson JD, Sprecher AF, Conrad H (eds) Electrorheological fluids. Proceedings of the Second International Conference on ER Fluids. Technomic, Lancaster, PA

Lanos C (2000) Identification of the rheological behaviour of mineral pastes by using compression test. Proceedings of the XIIIth International Congress on Rheology, Cambridge, UK, vol. 2, pp 415–417

Liddell PV, Boger DV (1996) Yield stress measurements with the vane. J Non-Newtonian Fluid Mech 63:235–261CrossRef

Lauridsen J, Twardos M, Dennin M (2002) Shear-induced stress relaxation in a two-dimensional wet foam. Phys Rev Lett 89(09303):1–4

Meeten GH (2000) Yield stress of structured fluids measured by squeeze flow. Rheol Acta 39:399–408CrossRef

Meeten GH (2002) Constant-force squeeze flow of soft solids. Rheol Acta 41:557–566CrossRef

Meeten GH (2004a) Squeeze flow of soft solids between rough surfaces. Rheol Acta 43:6–16CrossRef

Meeten GH (2004b) Effects of plate roughness in squeeze flow rheometry. J Non-Newtonian Fluid Mech 124:51–60CrossRef

Meeten GH (2007) Radial filtration during constant-force squeeze flow of soft solids. Rheol Acta 46:803–813CrossRef

Mélinge Y, Lanos C, Mortreil FX, Laquerbe M (2000) Heterogeneity and electric properties of sheared mineral paste. Proceedings of the XIIIth International Congress on Rheology, Cambridge, UK, vol. 3, pp 95–97

Møller CF, Mewis J, Bonn D (2006) Yield stress and thixotropy: on the difficulty of measuring yield stresses in practice. Soft Matter 2:274–283CrossRef

Nguyen QD, Boger DV (1985) Direct yield stress measurement with the vane method. J Rheol 29:335–347CrossRef

Oka S (1960) The principles of rheometry, chapter 2. In: Eirich FR (ed) Rheology theory and applications, vol 3. Academic, New York

Poitou A, Racineux G (2001) A squeezing experiment showing binder migration in concentrated suspensions. J Rheol 45:609–625CrossRef

Rodts S, Baudez JC, Coussot P (2005) From “discrete” to “continuum” flow in foams. Europhys Lett 69:636–642CrossRef

Rouyer F, Cohen-Addad S, Vignes-Adler M, Höhler R (2003) Dynamics of yielding observed in a three-dimensional aqueous dry foam. Phys Rev E 67(021405):1–7

Rouyer F, Cohen-Addad S, Höhler R (2005) Is the yield stress of aqueous foam a well-defined quantity. Colloids Surf A 263:111–116CrossRef

Saint-Jalmes A, Durian DJ (1999) Vanishing elasticity for wet foams: equivalence with emulsions and role of polydispersity. J Rheol 43:1411–1421CrossRef

Servais C, Ravji S, Sansonnens C, Bauwens I (2003) Oscillating vane geometry for soft solid gels and foams. J Texture Stud 33:487–504CrossRef

Sherwood JD, Durban D (1998) Squeeze-flow of a Herschel-Bulkley fluid. J Non-Newtonian Fluid Mech 77:115–121CrossRef

Sherwood JD (2003) Squeeze flow of a dry foam. J Non-Newtonian Fluid Mech 112:115–128CrossRef

Sherwood JD, Meeten GH (1991) The use of the vane to measure the shear modulus of linear elastic solids. J Non-Newtonian Fluid Mech 41:101–118CrossRef

Stokes JR, Telford JH (2004) Measuring the yield behaviour of structured fluids. J Non-Newtonian Fluid Mech 124:137–146CrossRef

Terriac E, Etrillard J, Cantat I (2006) Viscous force exerted on a foam at a solid boundary: influence of the liquid volume fraction and of the bubble size. Europhys Lett 74:909–915CrossRef

Tisné P, Doubliez L, Aloui F (2004) Determination of the slip layer thickness for a wet foam flow. Colloids Surf A 246:21–29CrossRef

Weaire D, Fortes MA (1994) Stress and strain in liquid and solid foams. Adv Phys 43:685–738CrossRef

Weaire D, Hutzler S (1999) The Physics of foams. Clarendon, Oxford

Weaire D, Hutzler S, Cox S, Kern N, Alonso MD, Drenckham W (2003) The fluid dynamics of foams. J Phys Condens Matter 15:S65–S73CrossRef

Wilson TH (1999) Tribology. In: Stephens JH (ed) Kempe’s Engineers Yearbook for 1999. Miller Freeman UK, Tonbridge, Kent, pp. 1795–1840

Xu Z, Rhaphaelides SN (2005) A dynamic U-tube rheometer of novel design for the study of weak gels and foams. Rheol Acta 45:77–82CrossRef

Yang F (1998) Exact solution for compressive flow of viscoplastic fluids under perfect slip wall boundary conditions. Rheol Acta 37:69–72

Zhang XD, Giles DW, Barocas VH, Yasunaga K, Macosko CW (1998) Measurement of foam modulus via a vane rheometer. J Rheol 42:871–889CrossRef

Titel: Squeeze-flow and vane rheometry of a gas–liquid foam
verfasst von: G. H. Meeten
Publikationsdatum: 01.11.2008
Verlag: Springer-Verlag
Erschienen in: Rheologica Acta / Ausgabe 8/2008
Print ISSN: 0035-4511
Elektronische ISSN: 1435-1528
DOI: https://doi.org/10.1007/s00397-008-0269-0

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Technik"

Springer Professional "Wirtschaft+Technik"

Weitere Artikel der Ausgabe 8/2008

Effect of a controlled pre-deformation history on extensional viscosity of dilute polymer solutions

Relaxation patterns of long, linear, flexible, monodisperse polymers: BSW spectrum revisited

Recoverable strains and retardation times of monodisperse suspensions of silicon dioxide spheres in poly(dimethylsiloxane)

Rheo-optic flow-induced crystallisation of polypropylene and polyethylene within confined entry–exit flow geometries

A shear rheometer for measuring shear stress and both normal stress differences in polymer melts simultaneously: the MTR 25

The influence of wall interaction on dynamic particle modelling of magneto-rheological suspensions between shearing plates

Premium Partner

Marktübersichten