nach oben

The International Journal of Advanced Manufacturing Technology

Erschienen in:

16.06.2020 | ORIGINAL ARTICLE

Study on the design and cutting performance of stepped bi-directional milling cutters for hole making of CFRP

verfasst von: Chen Tao, Li Rui, Xiang Jiupeng, Gao Weijie, Wang Yongsheng

Erschienen in: The International Journal of Advanced Manufacturing Technology | Ausgabe 9-10/2020

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

During hole making of carbon fiber reinforced plastic (CFRP) by helical milling, the tool wear is a main factor in machined surface damage, being unable to guarantee machining quality and accuracy, and restricting the improvement of hole making efficiency. In order to prolong the service life of cutters, this paper has carried out the research into the design, manufacture, and cutting performance of stepped bi-directional milling cutters, combining with hole making of CFRP by bi-directional helical milling. By the method of differential geometry, the geometric model of the profile shape and the mathematical model of the helical edge are established of the stepped bi-directional milling cutter. Additionally, based on the transformation matrix between grinding wheel and workpiece coordinates of any point, the track equation of grinding wheel is derived from grinding the side edge helical groove of the stepped bi-directional milling cutter. What is more, the grinding process and accuracy are measured about the designed stepped bi-directional milling cutter. The experiment of CFRP holes made by bi-directional helical milling is designed, and the experimental results show that the axial cutting force of stepped bi-directional milling cutters is smaller and fluctuates more gently than that of symmetrical bi-directional milling cutters in the backward milling. Especially, the former has better distributed and slower flank wear on the backward cutting edge, and better machining quality than the latter.

Vorheriger Artikel Study of the effects of important factors on the diameter accuracy of micro-shafts fabricated by TMTF-WEDG

Nächster Artikel Bayesian neural network–based thermal error modeling of feed drive system of CNC machine tool

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Robson BD, Dutra P, Lincoln CB, Anderson PP, João RF, Paulo DJ (2017) A review of helical milling process. Int J Mach Tools Manuf 120(5):27–48

Yang GL, Dong ZG, Kang RK, BaoY, Guo DM(2019) Research progress of helical milling. Acta Aeronautica et Astronautica Sinica 40(X):1-17(in Chinese).

Wang Q, Wu YB, Bitou T, Mitsuyoshi N, Tatauya F (2018) Proposal of a tilted helical milling technique for high quality hole drilling of CFRP: kinetic analysis of hole formation and material removal. Int J Adv Manuf Technol 94(9-12):4221–4235CrossRef

Zhou L, Dong H, Ke Y, Cheng GL (2016) Analysis of the chip-splitting performance of a dedicated cutting tool in dry orbital drilling process. Int J Adv Manuf Technol 90(5-8):1–15CrossRef

Liu G, Wang YF, Zhang H, Gao KY, Ke YL, Duan ZH (2014) Research on helical milling specialized tool based on chip-splitting principle. Journal of Mechanical Engineering 50(9):176-184(in Chinese).

Chen XF, Ding GF, Li R, Ma XJ, Qin SF, Song XL (2014) A new design and grinding algorithm for ball-end milling cutter with tooth offset center. J Eng Manuf 228(7):687–697CrossRef

Tian YL, Liu YP, Wang FJ, Jing XB, Zhang DW, Liu XP (2017) Modeling and analyses of helical milling process. Int J Adv Manuf Technol 90(1-4):1003–1022CrossRef

Ren L, Wang SL, Yi LL, Sun SL (2015) An accurate method for five-axis flute grinding in cylindrical end-mills using standard 1V1/1A1 grinding wheels. Precis Eng 43(9):387–394

Wang LL, Chen ZC, Li JF, Sun J (2016) A novel approach to determination of wheel position and orientation for five-axis CNC flute grinding of end mills. Int J Adv Manuf Technol 84(9-12):2499–2514CrossRef

10.

Nguyen H, Ko SL (2014) A mathematical model for simulating and manufacturing ball end mill. Comput Aided Des 50(1):6–26

11.

An QL, Cai CY, Cai XJ, Chen M (2019) Experimental investigation on the cutting mechanism and surface generation in orthogonal cutting of UD-CFRP laminates. Compos Struct 230:111441CrossRef

12.

Gökhan S, Ömer E (2018) Cutting tool geometry in the drilling of CFRP composite plates and Taguchi optimisation of the cutting parameters affecting delamination. Sigma Journal of Engineering and Natural Sciences Sigma Mühendislik ve Fen Bilimleri Dergisi 36(3):619–628

13.

Ömer E, Birhan I, Adem Ç, Fuat K (2013) Prediction of damage factor in end milling of glass fibre reinforced plastic composites using artificial neural network. Appl Compos Mater 20(4):517–536CrossRef

14.

Qi Z, Zhang K, Cheng H, Liu S (2015) Numerical simulation for delamination during drilling of CFRP/AL stacks. Mater Res Innov 19(Sup6):98–101CrossRef

15.

Ventura CEH, Hassui A (2013) Modeling of cutting forces in helical milling by analysis of tool contact angle and respective depths of cut. Int J Adv Manuf Technol 68(9):2311–2319CrossRef

16.

Norbert G, Tibor S (2017) Optimisation of process parameters for the orbital and conventional drilling of unidirectional carbon fibre-reinforced polymers (UD-CFRP). Measurement 110(7):319–334

17.

Brinksmeier E, Fangmann S, Meyer I (2008) Orbital drilling kinematics. Prod Eng 2(3):277–283CrossRef

18.

Boudelier A, Ritou M, Garnier S, Furet B (2018) Cutting force model for machining of CFRP laminate with diamond abrasive cutter. Prod Eng 12(2):279–287CrossRef

19.

Karpat Y, Polat N (2013) Mechanistic force modeling for milling of carbon fiber reinforced polymers with double helix tools. CIRP Ann-Manuf Technol 62(1):95–98CrossRef

20.

Voss R, Henerichs M, Kuster F (2016) Comparison of conventional drilling and orbital drilling in machining carbon fibre reinforced plastics (CFRP). CIRP Ann-Manuf Technol 65(1):137–140CrossRef

21.

Li ZQ, Liu Q, Ming XZ, Dong YF (2014) Cutting force prediction and analytical solution of regenerative chatter stability for helical milling operation. Int J Adv Manuf Technol 73(1-4):433–442CrossRef

22.

Li ZQ, Liu Q (2013) Surface topography and roughness in hole-making by helical milling. Int J Adv Manuf Technol 66(9-12):1415–1425CrossRef

23.

Shang YC, He N, Li L, Zhao W, Yang YF (2013) Vector modeling of robotic helical milling hole movement and theoretical analysis on roughness of hole surface. J Cent South Univ 20(7):1818–1824CrossRef

24.

An QL, Chen J, Cai XJ, Peng TT, Chen M (2018) Thermal characteristics of unidirectional carbon fiber reinforced polymer laminates during orthogonal cutting. J Reinf Plast Compos 37(13):905–916CrossRef

25.

Ömer E, Mustafa D, Birhan I, İbrahim NT (2014) Selection of optimal machining conditions for the composite materials by using Taguchi and GONNs. Measurement 48:306–313CrossRef

26.

Chen Y, Ge ND, Fu YC, Su HU, Xu JH (2015) Review and prospect of drilling technologies foe carbon fiber reinforced. Acta Materiae Compositae Sinica 32(2):301–314 (in Chinese)

27.

Dong HY, Chen GL, Zhou L, He FT, Liu ST (2017) Processing research on orbital drilling of CFRP/Ti-6Al-4V stacks. Acta Materiae Compositae Sinica 34(3):540–549 (in Chinese)

Titel: Study on the design and cutting performance of stepped bi-directional milling cutters for hole making of CFRP
verfasst von: Chen Tao
Li Rui
Xiang Jiupeng
Gao Weijie
Wang Yongsheng
Publikationsdatum: 16.06.2020
Verlag: Springer London
Erschienen in: The International Journal of Advanced Manufacturing Technology / Ausgabe 9-10/2020
Print ISSN: 0268-3768
Elektronische ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-020-05429-0

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 9-10/2020

A novel finite element investigation of cutting force in orthogonal cutting considering plough mechanism with rounded edge tool

Development of a simulation approach for laser powder bed fusion based on scanning strategy selection

Influence of wire parameters on the formability of DP600 steel sheets during wire explosion impact forming

Research on the tool tip trajectory deflection control and cutting characteristics of elliptical vibration cutting based on guided wave transmission

Loading path design of thin-walled aluminum alloy T-shaped tube hydroforming process based on the control of limit pressure

Study of the effects of important factors on the diameter accuracy of micro-shafts fabricated by TMTF-WEDG

Premium Partner

Marktübersichten