nach oben

The International Journal of Advanced Manufacturing Technology

Erschienen in:

02.02.2022 | Technical Note

Thin floor milling using moving support

verfasst von: Jixiong Fei, Bin Lin, Tian Huang, Juliang Xiao

Erschienen in: The International Journal of Advanced Manufacturing Technology | Ausgabe 1-2/2022

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

During milling of the thin floor of a pocket which is located on a monolithic structure, it is very difficult to achieve high accuracy and good surface quality due to its low rigidity. In this paper, a novel approach is proposed to overcome the difficulties that are encountered during milling of the thin floor. The method is realized by using a small axial depth of cut but placing a moving support at the back surface of the thin floor during machining, in which the support will move with the cutter at the same velocity. An experimental platform is built to demonstrate the validity of the proposed method. The experimental results show that the proposed method can effectively improve the accuracy and surface quality of the thin floor of a pocket on the monolithic structure.

Vorheriger Artikel Stability analysis and experimental research on ultrasonic cutting of wave-absorbing honeycomb material with disc cutter

Nächster Artikel Correction to: Decision-making for structural parameters of injection mold gating system based on agent model and intelligent algorithm

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Del Sol I, Rivero A, López de Lacalle LN, Gamez AJ (2019) Thin-wall machining of light alloys: a review of models and industrial approaches. Materials 12(12):2012

Wang X, Bi Q, Zhu L, Ding H (2018) Improved forecasting compensatory control to guarantee the remaining wall thickness for pocket milling of a large thin-walled part. Int J Adv Manuf Technol 94(5):1677–1688. https://doi.org/10.1007/s00170-016-9785-8CrossRef

Schmitt RH, Peterek M, Morse E, Knapp W, Galetto M, Härtig F, Goch G, Hughes B, Forbes A, Estler WT (2016) Advances in large-scale metrology – review and future trends. CIRP Ann-Manuf 65(2):643–665. https://doi.org/10.1016/j.cirp.2016.05.002CrossRef

Zhang J, Lin B, Fei J, Huang T, Xiao J, Zhang X, Ji C (2018) Modeling and experimental validation for surface error caused by axial cutting force in end-milling process. Int J Adv Manuf Technol 99(1):327–335. https://doi.org/10.1007/s00170-018-2468-xCrossRef

Huang N, Yin C, Liang L, Hu J, Wu S (2018) Error compensation for machining of large thin-walled part with sculptured surface based on on-machine measurement. Int J Adv Manuf Technol 96(9):4345–4352. https://doi.org/10.1007/s00170-018-1897-xCrossRef

Bi Q, Huang N, Zhang S, Shuai C, Wang Y (2019) Adaptive machining for curved contour on deformed large skin based on on-machine measurement and isometric mapping. Int J Mach Tools Manuf 136:34–44. https://doi.org/10.1016/j.ijmachtools.2018.09.001CrossRef

Kolar P, Sveda J, Koubek J (2018) Case study 2.2: clamping of thin-walled curved workpieces. In: Intelligent fixtures for the manufacturing of low rigidity components. Springer International Publishing. Cham 81–98. https://doi.org/10.1007/978-3-319-45291-3_5

Fu Q, Lorite GS, Rashid MM-U, Selkälä T, Uusitalo J, Toth G, Kordas K, Österlind T, Nicolescu CM (2015) Suppressing tool chatter with novel multi-layered nanostructures of carbon based composite coatings. J Mater Process Technol 223:292–298. https://doi.org/10.1016/j.jmatprotec.2015.03.043CrossRef

Kolluru K, Axinte D (2014) Novel ancillary device for minimising machining vibrations in thin wall assemblies. Int J Mach Tools Manuf 85(7):79–86. https://doi.org/10.1016/j.ijmachtools.2014.05.007CrossRef

10.

Kolluru K, Axinte D, Becker A (2013) A solution for minimising vibrations in milling of thin walled casings by applying dampers to workpiece surface. CIRP Ann-Manuf 62(1):415–418. https://doi.org/10.1016/j.cirp.2013.03.136CrossRef

11.

https://www.mtorres.es/sites/default/files/documentos/fichas-de-producto/Torresmil%26Torrestool_0.pdf

12.

Qin G, Zhang W, Wan M (2005) Analysis and optimal design of fixture clamping sequence. J Manuf Sci Eng 128(2):482–493. https://doi.org/10.1115/1.2162908CrossRef

13.

Chaari R, Abennadher M, Louati J, Haddar M (2014) Mathematical methodology for optimization of the clamping forces accounting for workpiece vibratory behaviour. Int J Simul Multidiscipl Des Optim 5:A13. https://doi.org/10.1051/smdo/2013005CrossRef

14.

Chen W, Ni L, Xue J (2007) Deformation control through fixture layout design and clamping force optimization. Int J Adv Manuf Technol 38(9):860–867. https://doi.org/10.1007/s00170-007-1153-2CrossRef

15.

Sundararaman KA, Padmanaban KP, Sabareeswaran M (2015) Optimization of machining fixture layout using integrated response surface methodology and evolutionary techniques. Proc Inst Mech Eng Part C-j Eng Mech 230(13):2245–2259. https://doi.org/10.1177/0954406215592920CrossRef

16.

Yang B, Wang Z, Yang Y, Kang Y, Li X (2016) Optimum fixture locating layout for sheet metal part by integrating kriging with cuckoo search algorithm. Int J Adv Manuf Technol 91(1–4):327–340. https://doi.org/10.1007/s00170-016-9638-5CrossRef

17.

Liu SG, Zheng L, Zhang ZH, Li ZZ, Liu DC (2007) Optimization of the number and positions of fixture locators in the peripheral milling of a low-rigidity workpiece. Int J Adv Manuf Technol 33(7–8):668–676. https://doi.org/10.1007/s00170-006-0507-5CrossRef

18.

Zeng S, Wan X, Li W, Yin Z, Xiong Y (2012) A novel approach to fixture design on suppressing machining vibration of flexible workpiece. Int J Mach Tools Manuf 58:29–43. https://doi.org/10.1016/j.ijmachtools.2012.02.008CrossRef

19.

Long X (2006) Loss of contact and time delay dynamics of milling processes. Doctoral dissertation. University of Maryland

20.

Balachandran B (2001) Nonlinear dynamics of milling processes. Philos T Roy Soc A 359(1781):793–819. https://doi.org/10.1098/rsta.2000.0755CrossRefMATH

21.

Shamoto E, Mori T, Nishimura K, Hiramatsu T, Kurata Y (2010) Suppression of regenerative chatter vibration in simultaneous double-sided milling of flexible plates by speed difference. CIRP Ann-Manuf 59(1):387–390. https://doi.org/10.1016/j.cirp.2010.03.028CrossRef

22.

Mori T, Hiramatsu T, Shamoto E (2011) Simultaneous double-sided milling of flexible plates with high accuracy and high efficiency—suppression of forced chatter vibration with synchronized single-tooth cutters. Precis Eng 35(3):416–423. https://doi.org/10.1016/j.precisioneng.2011.02.002CrossRef

23.

Fei J, Lin B, Xiao J, Ding M, Yan S, Zhang X, Zhang J (2018) Investigation of moving fixture on deformation suppression during milling process of thin-walled structures. J Manuf Processes 32:403–411. https://doi.org/10.1016/j.jmapro.2018.03.011CrossRef

24.

Fei J, Lin B, Yan S, Ding M, Xiao J, Zhang J, Zhang X, Ji C, Sui T (2017) Chatter mitigation using moving damper. J Sound Vib 410:49–63. https://doi.org/10.1016/j.jsv.2017.08.033CrossRef

25.

Ozturk E, Barrios A, Sun C, Rajabi S, Munoa J (2018) Robotic assisted milling for increased productivity. CIRP Ann-Manuf 67(1):427–430. https://doi.org/10.1016/j.cirp.2018.04.031CrossRef

26.

Davies MA, Balachandran B (2000) Impact dynamics in milling of thin-walled structures. Nonlinear Dynam 22(4):375–392. https://doi.org/10.1023/A:1008364405411CrossRefMATH

27.

Huang T, Dong C, Liu H, Sun T, Chetwynd DG (2018) A simple and visually orientated approach for type synthesis of overconstrained 1T2R parallel mechanisms. Robotica:1–13.https://doi.org/10.1017/S0263574718000395

28.

Huang T, Chenglin D, Liu H, Xuda Q, Mei J, Liu Q, Manxin W (2018) Five-degree-of-freedom hybrid robot with rotational supports, US Pantent. US9943967B2

29.

Dong C, Liu H, Yue W, Huang T (2017) Stiffness modeling and analysis of a novel 5-DOF hybrid robot. Mech Mach Theory. https://doi.org/10.1016/j.mechmachtheory.2017.12.009CrossRef

30.

Xiao JL, Zhao SL, Guo H, Huang T, Lin B (2017) An integrated pneumatic rigid mirror milling flexible support device for real-time measurement of thickness. China Patents

31.

Liu Q, Huang T (2019) Inverse kinematics of a 5-axis hybrid robot with non-singular tool path generation. Robot Cim-int Manuf 56:140–148. https://doi.org/10.1016/j.rcim.2018.06.003CrossRef

32.

Liu Q, Xiao J, Yang X, Liu H, Huang T, Chetwynd DG (2019) An iterative tuning approach for feedforward control of parallel manipulators by considering joint couplings. Mech Mach Theory 140:159–169. https://doi.org/10.1016/j.mechmachtheory.2019.05.017CrossRef

Titel: Thin floor milling using moving support
verfasst von: Jixiong Fei
Bin Lin
Tian Huang
Juliang Xiao
Publikationsdatum: 02.02.2022
Verlag: Springer London
Erschienen in: The International Journal of Advanced Manufacturing Technology / Ausgabe 1-2/2022
Print ISSN: 0268-3768
Elektronische ISSN: 1433-3015
DOI: https://doi.org/10.1007/s00170-022-08814-z

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 1-2/2022

Time-optimal trajectory optimization of serial robotic manipulator with kinematic and dynamic limits based on improved particle swarm optimization

Modeling of thrust and torque for drilling PTFE materials

Analysis and optimization of the properties of the grinding contact line for form-grinding modified helical gears

Application of machine learning to predict and diagnose for hot-rolled strip crown

Mechanism analysis and engineering experiment of multi-directional pressing-forming complex large-size automobile axle housing

Local strain analysis under quasi-static tensile loading in Al/steel dissimilar friction stir weld by a digital image correlation method

Premium Partner

Marktübersichten