nach oben

Journal of Materials Engineering and Performance

Erschienen in:

22.01.2016

Tribological Behavior of Babbitt Alloy Rubbing Against Si₃N₄ and Steel Under Dry Friction Condition

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 3/2016

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The tribological behavior of Babbitt alloy rubbing with Si₃N₄ ball and steel ball with various sliding speeds at dry friction condition was investigated. It was found that B88 alloy rubbing with Si₃N₄ ball and steel ball possesses a low sliding wear resistance at dry friction. The wear rate is above 10⁻⁴ mm³/Nm, and the friction coefficient is from 0.2 to 0.4. At low sliding speed of 0.05-0.1 m/s, the mainly wear mechanisms are microgroove and fatigue wear, while at high sliding speed of 0.5 m/s, the wear mechanisms depend on plastic deformation and delamination. The high wear rate indicates that it is needed to prevent Babbitt alloy from working at dry friction conditions, while the low friction coefficient suggests that it is not easy to the occurrence of cold weld.

Vorheriger Artikel Fatigue of Austempered Ductile Iron with Two Strength Grades in Very High Cycle Regime

Nächster Artikel Influence of Zn Interlayer on Interfacial Microstructure and Mechanical Properties of TIG Lap-Welded Mg/Al Joints

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

M. Goudarzi, S.A. Jenabali Jahromi, and A. Nazarboland, Investigation of Characteristics of Tin-Based White Metals as a Bearing Material, Mater. Des., 2009, 30, p 2283–2288CrossRef

B.S. Unlu, Investigation of Tribological and Mechanical Properties of Metal Bearings, Bull. Mater. Sci., 2009, 32, p 451–457CrossRef

H.R. Wu, Q.L. Bi, S.Y. Zhu, J. Yang, and W.M. Liu, Friction and Wear Properties of Babbitt Alloy 16-16-2 Under Sea Water Environment, Tribol. Int., 2011, 44, p 1161–1167CrossRef

H.R. Wu, Q.L. Bi, J. Yang, and W.M. Liu, Tribological Performance of Tin-Based White Metal ZChSnSb 8-8 Under Simulated Sea Water Environment, Chin. Tribol., 2011, 31, p 271–277

A. Zeren, E. Feyzullahoylu, and M. Zeren, A Study on Tribological Behavior of Tin-Based Bearing Material in Dry Sliding, Mater. Des., 2007, 28, p 318–323CrossRef

A.K. Valeeva, I.S. Valeev, and R.F. Fazlyakhmetov, Effect of Structure of B83 Babbit on Its Wear, J Frict. Wear., 2014, 35, p 311–315CrossRef

F.A. Sadykov, N.P. Barykin, ISh Valeev, and V.N. Danilenko, Influence of the Structural State on Mechanical Behavior of Tin Babbit, J. Mater. Eng. Perform., 2003, 12(1), p 29–36CrossRef

A. Zeren, Embeddability Behavior of Tin-Based Bearing Material in Dry Sliding, Mater. Des., 2007, 28, p 2344–2350CrossRef

N.P. Barykin, F.A. Sadykov, and I.R. Aslanian, Wear and Failure of Babbit Bushes in Steam Turbine Sliding Bearings, J. Mater. Eng. Perform., 2000, 9, p 110–115CrossRef

10.

M. Bora, O. Coban, T. Sinmazcelik, V. Günay, and M. Zeren, Instrumented Indentation and Scratch Testing Evaluation of Tribological Properties of Tin-Based Bearing Materials, Mater. Des., 2010, 31, p 2707–2715CrossRef

11.

K. Thoma, L. Rohr, H. Rehmann, S. Roos, and J. Michler, Materials Failure Mechanisms of Hybrid Ball Bearings with Silicon Nitride Balls, Tribol. Int., 2004, 37, p 463–471CrossRef

12.

C. Liu, J. Gu, X. Chen, and X. Xia, Performance Analysis and Experiments of Hybrid Bearing for Micro-Satellite Attitude Control Momentum Wheel, Chin. J Astron., 2007, 28, p 427–431

13.

S. Das, A.T. Morale, and A.T. Alpas, Microstructural Evolution During High Temperature Sliding Wear of Mg-3%Al-1%Zn (AZ31) Alloy, Wear, 2010, 268, p 94–103CrossRef

14.

C. Liang, C. Li, J. An, M. Yu, Y.C. Hu, W.H. Lin, F. Liu, and Y.H. Ding, Effect of Microstructural Evolution and Hardening in Subsurface on Wear Behavior of Mg-3Al-1Zn Alloy, J. Mater. Eng. Perform., 2013, 22, p 3783–3791CrossRef

15.

H. Somekawa, S. Meada, T. Hirayama, T. Mitsuoka, T. Inoue, and T. Mukai, Microstructural Evolution During Dry Wear Test in Magnesium and Mg-Y Alloy, Mater. Sci. Eng. A, 2013, 561, p 371–377CrossRef

16.

Q.B. Nguyen, Y.H.M. Sim, M. Gupta, and C.Y.H. Lim, Tribological Characteristics of Magnesium Alloy AZ31B and Its Composites, Tribol. Int., 2015, 82, p 464–471CrossRef

17.

D. Zhang, J.L. Ho, G. Dong, H. Zhang, and M. Hua, Tribological Properties of Tin-Based Babbitt Bearing Alloy with Polyurethane Coating Under Dry and Starved Lubrication Conditions, Tribol. Int., 2015, 90, p 22–31CrossRef

Titel: Tribological Behavior of Babbitt Alloy Rubbing Against Si3N4 and Steel Under Dry Friction Condition
Publikationsdatum: 22.01.2016
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 3/2016
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-016-1893-y

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 3/2016

Constitutive Modeling of High-Temperature Flow Behavior of an Nb Micro-alloyed Hot Stamping Steel

Hot Ductility of the 17-4 PH Stainless Steels

A Very High-Cycle Fatigue Test and Fatigue Properties of TC17 Titanium Alloy

Influence of Dispersion in Composites of Chopped PAN-Based Carbon Fiber Modified by Dodecyl Ether Carboxylate

Improved Corrosion Resistance of As-Extruded GZ51K Biomagnesium Alloy with High Mechanical Properties by Aging Treatment

Development of Texture in Interstitial-Free Steel Processed by Equal-Channel Angular Pressing

Premium Partner

Marktübersichten