nach oben

Rock Mechanics and Rock Engineering

Erschienen in:

05.09.2023 | Original Paper

Experimental Investigation into the Effect of Process Parameters on the Drilling Performance for Swirling Impeller Abrasive Water Jet

verfasst von: Huan Li, Jingbin Li, Zhongwei Huang, Kang Cheng, Jingru Hu, Wenbin Li

Erschienen in: Rock Mechanics and Rock Engineering | Ausgabe 12/2023

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Radial jet drilling (RJD) is an innovative geological resource development technology. Swirling impeller abrasive water jet (SAWJ) is an excellent rock drilling method and is expected to drill larger branches during RJD. However, the rock drilling performance of a SAWJ is affected by various parameters. Here, we conducted SAWJ rock drilling experiments under different parameter combinations. Jet-drilled hole morphology, diameter, depth and volume were utilized to evaluate the rock drilling performance. Besides the SAWJ rock-breaking mechanisms, differences between SAWJ and conical abrasive water jet were discussed. The results indicated that the SAWJ has the ability to create a large diameter (56 ~ 79 mm) hole on granite, limestone, conglomerate, gray sandstone, yellow sandstone and coal. The jet-drilled hole diameter strongly depends on standoff distance, and large hole diameter was obtained at a long standoff distance. The jet-drilled hole depth and volume tends to increase with an increase in the jetting pressure, abrasive mass concentration, abrasive particle diameter and exposure time and with a decrease in the standoff distance. The critical jetting pressure and effective standoff distance were 10 MPa and 30 mm, respectively. Besides, the rock failure modes during SAWJ drilling are not only the compressive failure but also the tensile failure and shear failure. In addition, the SAWJ has the characteristics of large impact area (28.26 cm²) and short effective standoff distance (3 cm). The experiments results are expected to provide a theoretical basis for parameters selection during RJD filed applications.

Vorheriger Artikel Loaded Failure Characteristics of Anthracite Derived from Microwave Irradiation: Acoustic Emission Evaluation

Nächster Artikel Mechanical Behaviour of a Deep Soft Rock Large Deformation Roadway Supported by NPR Bolts: A Case Study

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Barton N (1978) Suggested methods for the quantitative description of discontinuities in rock masses: International Society for Rock Mechanics. Int J Rock Mech Min Sci Geomech Abstr 15:319–368

Cai C, Wang X, Yuan X, Kang Y, Wang Z, Huang M, Chen H (2019) Experimental investigation on perforation of shale with ultra-high pressure abrasive water jet: shape, mechanism and sensitivity. J Nat Gas Sci Eng 67:196–213. https://doi.org/10.1016/j.jngse.2019.05.002CrossRef

Cao Y, Wang R, Zhou W, Bu Y (2001) Experimental study on casing erosion by rotating abrasive jet. Pet Drill Tech 4:17–18

Chen J, Yang R, Huang Z, Li G, Qin X, Li J, Wu X (2022) Detached eddy simulation on the structure of swirling jet flow field. Pet Explor Dev 49(4):806–817CrossRef

Du P, Peng X, Wei Z, Xu B (2022) Flow field investigation of a straight-swirling integrated jet for radial jet drilling. Energy Rep 8:7434–7443. https://doi.org/10.1016/j.egyr.2022.05.246CrossRef

Engin IC (2012) A correlation for predicting the abrasive water jet cutting depth for natural stones. S Afr J Sci 108(9–10):69–79. https://doi.org/10.4102/sajs.v108i9/10.692CrossRef

Fu X, Li G, Huang Z, Liang Y, Xu Z, Jin X (2015) Experimental and numerical study of radial lateral fracturing for coalbed methane. J Geophys Eng 12(5):875–886. https://doi.org/10.1088/1742-2132/12/5/875CrossRef

Fu B, Zhang S, Liu S, Zhu Z (2021) Drilling performance analysis of a new type of direct-rotating mixed-jet nozzle. J Petrol Sci Eng 200:11. https://doi.org/10.1016/j.petrol.2020.108302CrossRef

Guo T, Gong F, Shen L, Qu Z, Qi N, Wang T (2019) Multi-fractured stimulation technique of hydraulic fracturing assisted by radial slim holes. J Petrol Sci Eng 174:572–583. https://doi.org/10.1016/j.petrol.2018.11.064CrossRef

Hong C, Yang R, Huang Z, Liu W, Chen J, Cong R (2021) Experimental investigation on coal-breakage performances by abrasive nitrogen-gas jet with a conical nozzle. Int J Rock Mech Min Sci 142:13. https://doi.org/10.1016/j.ijrmms.2021.104781CrossRef

Huang F, Zhao Z, Li D, Mi J, Wang R (2022) Investigation of the breaking manifestations of bedded shale impacted by a high-pressure abrasive water jet. Powder Technol 397:117021. https://doi.org/10.1016/j.powtec.2021.11.065CrossRef

Huang Z, Huang Z (2018) Review of radial jet drilling and the key issues to be applied in new geo-energy exploitation. In: 10th International Conference on Applied Energy (ICAE). Energy Procedia. Elsevier Science Bv, Hong Kong, Hong Kong, pp. 5969–5974

Kamel A H (2017) Radial jet drilling: a technical review, SPE Middle East Oil & Gas Show and Conference

Li G, Niu J, Liu Z, Zhang Y (2002) Experimental study on mechanisms of Hydraulic sand blasting perforation for improvement of oil production. J Univ Pet China (ed Nat Sci) 26(2):31–34

Li G, Huang Z, Li J (2017) Study of the key techniques in radial jet drilling. Pet Drill Tech 45(2):1–9

Li G, Tian S, Zhang Y (2020a) Research progress on key technologies of natural gas hydrate exploitation by cavitation jet drilling of radial wells. Pet Sci Bull 5(3):349–365

Li J, Huang Z, Zhang G, Liu X, Li H (2020b) Rock breaking characteristics of the self-rotating multi-orifices nozzle applied to coalbed methane radial jet drilling. Int J Rock Mech Min Sci 136:8. https://doi.org/10.1016/j.ijrmms.2020.104483CrossRef

Li J, Dai J, Huang Z, Zhang G, Liu X, Li H (2021) Rock breaking characteristics of the self-rotating multi-orifice nozzle for sandstone radial jet drilling. Rock Mech Rock Eng 54(11):5603–5615. https://doi.org/10.1007/s00603-021-02567-zCrossRef

Li H, Huang Z, Li J, Li X, Jiang T, Chen J (2022) Rock breaking characteristics by swirling impeller abrasive water jet (SAWJ) on granite. Int J Rock Mech Min Sci 159:13. https://doi.org/10.1016/j.ijrmms.2022.105230CrossRef

Liu S, Zhou F, Li H, Chen Y, Wang F, Guo C (2020) Experimental investigation of hard rock breaking using a conical pick assisted by abrasive water jet. Rock Mech Rock Eng 53(9):4221–4230. https://doi.org/10.1007/s00603-020-02168-2CrossRef

Ma G, Li J, Li H, Zhang J, Chang W (2021) Study on pore forming characteristics of carbonate rock broken by Swirling abrasive water jet. Fluid Mach 49(11):12

Nagar A, Savelyev A, Mukerjee A, Hatchell I, Jelsma H, Maniar C, Bhad N, Pathak S, Shrivastava P, Nekkanti S, Bohra A, Vermani S (2020) Radial Jet Drilling Improves Injectivity & Conformance in High Permeability Layered Sandstone Reservoir Across Mangala, Bhagyam & Aishwarya Onshore Fields in India, SPE Asia Pacific Oil & Gas Conference and Exhibition

Nguyen TT, Sulem J, Muhammed RD, Dupla JC, Canou J, Boero-Rollo JG, Ochi J (2022) An experimental setup with radial injection cell for investigation of fracturing in unconsolidated sand reservoirs under fluid injection. J Petrol Sci Eng 213:18. https://doi.org/10.1016/j.petrol.2022.110362CrossRef

Oh TM, Cho GC (2014) Characterization of effective parameters in abrasive waterjet rock cutting. Rock Mech Rock Eng 47(2):745–756. https://doi.org/10.1007/s00603-013-0434-3CrossRef

Oh TM, Cho GC (2016) Rock cutting depth model based on kinetic energy of abrasive waterjet. Rock Mech Rock Eng 49(3):1059–1072. https://doi.org/10.1007/s00603-015-0778-yCrossRef

Oh TM, Joo GW, Cho GC (2019) Effect of abrasive feed rate on rock cutting performance of abrasive waterjet. Rock Mech Rock Eng 52(9):3431–3442. https://doi.org/10.1007/s00603-019-01784-xCrossRef

Qu H, Wu X, Huang P, Tang S, Wang R, Hu Y (2022) Acoustic emission and failure characteristics of shales with different brittleness under AWJ impingement. Rock Mech Rock Eng. https://doi.org/10.1007/s00603-021-02765-9CrossRef

Shi Y, Song X, Shen Z, Wang G, Li X, Zheng R, Geng L, Li J, Zhang S (2018) Numerical investigation on heat extraction performance of a CO₂ enhanced geothermal system with multilateral wells. Energy 163:38–51. https://doi.org/10.1016/j.energy.2018.08.060CrossRef

Shi Y, Song X, Wang G, Li J, Geng L, Li X (2019a) Numerical study on heat extraction performance of a multilateral-well enhanced geothermal system considering complex hydraulic and natural fractures. Renew Energy 141:950–963. https://doi.org/10.1016/j.renene.2019.03.142CrossRef

Shi Y, Song X, Li J, Wang G, YuLong F, Geng L (2019b) Analysis for effects of complex fracture network geometries on heat extraction efficiency of a multilateral-well enhanced geothermal system. Appl Therm Eng. https://doi.org/10.1016/j.applthermaleng.2019.113828CrossRef

Shi Y, Song X, Li J, Wang G, Zheng R, YuLong F (2019c) Numerical investigation on heat extraction performance of a multilateral-well enhanced geothermal system with a discrete fracture network. Fuel 244:207–226. https://doi.org/10.1016/j.fuel.2019.01.164CrossRef

Song X, Shi Y, Li G, Yang RY, Wang G, Zheng R, Li J, Lyu Z (2018) Numerical simulation of heat extraction performance in enhanced geothermal system with multilateral wells. Appl Energy 218:325–337. https://doi.org/10.1016/j.apenergy.2018.02.172CrossRef

Tian Y, Qu Z, Guo T, Tian Y (2017) Theoretical research on radial wells orientating hydraulically created fracture directional extended. Int J Hydrogen Energy 42(29):18358–18363. https://doi.org/10.1016/j.ijhydene.2017.04.179CrossRef

Tian S, Huang Z, Li G, Lu P, Zhang H, Wang T (2018) Laboratory experiments on blockage removing and stimulation of CBM reservoirs by composite pulsating fracturing of radial horizontal wells. Nat Gas Ind 38(9):88–94

Wang R, Zhou A, Zhou W, Li L (2012) Numerical simulation and experimental verification of casing window with swirling abrasive jet. J China Univ Pet 36(5):80–83

Wang T, Guo Z, Li G, Ma Z, Yong Y, Chang X, Tian S (2023) Numerical simulation of three-dimensional fracturing fracture propagation in radial wells. Pet Explor Dev 50(2):1–11. https://doi.org/10.11698/PED.20220458CrossRef

Yan C, Ren X, Cheng Y, Zhao K, Deng F, Liang Q, Zhang J, Li Y, Li Q (2019) An experimental study on the hydraulic fracturing of radial horizontal wells. Geomech Eng 17(6):535–541. https://doi.org/10.12989/gae.2019.17.6.535CrossRef

Yang R, Hong C, Huang Z, Song X, Zhang S, Wen H (2019) Coal breakage using abrasive liquid nitrogen jet and its implications for coalbed methane recovery. Appl Energy 253:18. https://doi.org/10.1016/j.apenergy.2019.113485CrossRef

Yang R-Y, Li G-S, Qin X-Z, Huang Z-W, Li J-B, Sheng M, Wang B (2022a) Productivity enhancement in multilayered coalbed methane reservoirs by radial borehole fracturing. Pet Sci 19(6):2844–2866. https://doi.org/10.1016/j.petsci.2022.06.019CrossRef

Yang R, Huang Z, Li G, Chen J, Wen H, Qin X (2022b) Investigation of hydraulic jet multistage cavity completion in coalbed methane horizontal wells. J China Coal Soc 47(9):3284–3297

Yongyin Y, Zhonghou S, Ruihe W, Weidong Z (1999) Experimental study on rotary abrasive jet drilling. Pet Drill Tech 27(4):4

Zhang P, Tian S, Zhang Y, Li G, Zhang W, Khan WA, Ma L (2021) Numerical simulation of gas recovery from natural gas hydrate using multi-branch wells: a three-dimensional model. Energy 220:14. https://doi.org/10.1016/j.energy.2020.119549CrossRef

Zhao W, Ge J, Wang T, Zhang H, Li Y (2020) Study on catastrophe mechanism of hydraulic fracturing fracks initiation in radial boreholes. Geomech Geophys Geo-Energy Geo-Resour 6(3):15. https://doi.org/10.1007/s40948-020-00169-7CrossRef

Zhou A, Wang R, Zhou W, Li L (2012) Experiment study on casing window with swirling abrasive jet. Drill Prod Technol 35(3):28–30

Titel: Experimental Investigation into the Effect of Process Parameters on the Drilling Performance for Swirling Impeller Abrasive Water Jet
verfasst von: Huan Li
Jingbin Li
Zhongwei Huang
Kang Cheng
Jingru Hu
Wenbin Li
Publikationsdatum: 05.09.2023
Verlag: Springer Vienna
Erschienen in: Rock Mechanics and Rock Engineering / Ausgabe 12/2023
Print ISSN: 0723-2632
Elektronische ISSN: 1434-453X
DOI: https://doi.org/10.1007/s00603-023-03519-5

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 12/2023

Correction: Water-Weakening Effects on the Failure Behavior of Mudstones

Stability Analysis and Deformation Control of Tunnel with Extremely Weak Surrounding Rocks Caused by Strike-Slip Fault Activity

Permeability–Friction Relationships for Propped Fractures in Shale

Generating Stochastic Structural Planes by Considering Parameter Correlations Using Deep Generative Adversarial Networks

Fracturing and Energy Evolution of Rock Around Prefabricated Rectangular and Circular Tunnels Under Shearing Load: A Comparative Analysis

Mechanical Behaviour of a Deep Soft Rock Large Deformation Roadway Supported by NPR Bolts: A Case Study