nach oben

Journal of Materials Engineering and Performance

Erschienen in:

04.10.2021

Tribological Behavior of Laser Surface Melted γ-TiAl Fabricated by Electron Beam Additive Manufacturing

verfasst von: G. V. Krishna Pradeep, Muthukannan Duraiselvam, K. Sivaprasad

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 2/2022

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Gamma titanium aluminide intermetallic alloys (γ-TiAl) are widely used in automotive and aerospace engineering fields to achieve weight reduction of various components. The γ-TiAl alloy which is used in engine valves of stated fields are affected through several tribological aspects. In the present study, γ-TiAl fabricated by electron beam melting (EBM) has been melted using fiber laser. The aim of the present work is to study the tribological behavior of EBM fabricated γ-TiAl treated with laser surface melting (LSM) which is done in a controlled atmosphere with different laser processing conditions. Metallurgical characterization of LSM samples was studied using field emission scanning electron microscope (FESEM). The wear resistance of substrate and LSM samples were analyzed using a tribometer. Load, speed, velocity, and sliding distance are considered as input parameters for the wear study. The improvement in microhardness is found in the LSM melted zone when compared to the substrate. The wear rate of LSM samples at 500, 600, and 700 W power with constant scanning velocity of 450 mm/min are lower than that of the substrate material. The surface roughness of LSM samples was also analyzed with substrate which shows better surface finish.

Vorheriger Artikel The Preparation and Properties of ZnAl Coating for Ring-Shaped Bonded NdFeB Magnet with High Corrosion Resistance

Nächster Artikel Impact of Carbon Fiber Reinforcement on Mechanical and Tribological Behavior of 3D-Printed Polyethylene Terephthalate Glycol Polymer Composites—An Experimental Investigation

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

H. Clemens, W. Smarsly, V. Güther, and S. Mayer, Advanced Intermetallic Titanium Aluminides. Proceedings of the 13th World Conference on Titanium, 2016, p 1189–1200. https://doi.org/10.1002/9781119296126.ch203

C. Zambaldi and D. Raabe, Plastic Anisotropy of γ-TiAl Revealed by Axisymmetric Indentation, Acta Mater., 2010, 58(9), p 3516–3530. https://doi.org/10.1016/j.actamat.2010.02.025CrossRef

P. Bartolotta, J. Barrett, T. Kelly and R. Smashey, Use of Cast Ti-48Al-2Cr-2Nb in Jet Engines, Jom, 1997, 49(5), p 48–51. https://doi.org/10.1007/bf02914685CrossRef

S.C. Huang, US Patent, 1989, 4879092

F. Lai, S. Qu, H. Qin, R. Lewis, T. Slatter, X. Li, and H. Luo, A Comparison of Wear Behaviour of Heat-Resistant Steel Engine Valves and TiAl Engine Valves. Proc. Inst. Mech. Eng. Part J. J. Eng. Tribol. 2020, 234(10), 1549–1562.

M. Panţuru, D. Chicet, C. Paulin, A. Alexandru, and C. Munteanu, Wear Aspects of Internal Combustion Engine Valves, IOP Conf. Ser. Mater. Sci. Eng., 2016, 147(1).

D.M. Roessler, Laser processing of materials for automotive applications, Mater. Manuf. Process., 1989, 4(3), p 285–310. https://doi.org/10.1080/10426918908956296CrossRef

Y.D. Kim and W.S. Kim, A Numerical Analysis of Heat and Fluid Flow with a Deformable Curved Free Surface in a Laser Melting Process, Int. J. Heat Fluid Flow, 2008, 29(5), p 1481–1493. https://doi.org/10.1016/j.ijheatfluidflow.2008.06.009CrossRef

L. Li, Advances and Characteristics of High-Power Diode Laser Materials Processing, Opt. Lasers Eng., 2000, 34(4–6), p 231–253. https://doi.org/10.1016/S0143-8166(00)00066-XCrossRef

10.

W.M. Steen, Laser material processing, 3rd edn, Springer, London

11.

K.F. Alabeedi, J.H. Abboud and K.Y. Benyounis, Microstructure and Erosion Resistance Enhancement of Nodular Cast Iron by Laser Melting, Wear, 2009, 266(9–10), p 925–933. https://doi.org/10.1016/j.wear.2008.12.015CrossRef

12.

S.P. L. Kumar and D. Avinash, Review on Effect of Ti-Alloy Processing Techniques on Surface-Integrity for Biomedical Application, Mater. Manuf. Process., Taylor & Francis, 2020, 35(8), p 869–892. https://doi.org/10.1080/10426914.2020.1748195

13.

Y. Xianqing, Z. Chengjun, S. Xuefeng, H. Manping and M. Jianguo, Microstructure Evolution of WC/Steel Composite by Laser Surface Re-Melting, Appl. Surf. Sci., 2007, 253(9), p 4409–4414. https://doi.org/10.1016/j.apsusc.2006.09.061CrossRef

14.

X. Guozhi, Z. Jingxian, L. Yijun, W. Keyu, M. Xiangyin and L. Pinghua, Effect of Laser Remelting on Corrosion Behavior of Plasma-Sprayed Ni-Coated WC Coatings, Mater. Sci. Eng. A, 2007, 460–461, p 351–356. https://doi.org/10.1016/j.msea.2007.01.064CrossRef

15.

J. Dutta Majumdar and I. Manna, Laser Material Processing, Int. Mater. Rev., 2011, 56(5–6), p 341–388. https://doi.org/10.1179/1743280411Y.0000000003

16.

K.R. Rakesh, S. Bontha, M.R. Ramesh, S.B. Arya, M. Das, V.K. Balla, and A. Srinivasan, Laser Surface Modification of Mg-Zn-Gd Alloy: Microstructural, Wettability and in Vitro Degradation Aspects, Mater. Res. Express, IOP Publishing, 2018, https://doi.org/10.1088/2053-1591/aadec6

17.

B.S. Yilbaş, A.Z. Şahin, M. Sami, A. Çoban and R. Bozdogan, Study into Laser Heating of Ti14Al21Nb Alloy to Improve Properties, Opt. Lasers Eng., 1995, 23(1), p 53–64. https://doi.org/10.1016/0143-8166(94)00022-3CrossRef

18.

A. Zieliński, J. Magdalena, A. Narożniak-Łuksza and W. Serbiński, Surface Structure and Properties of Ti6Al4V Alloy Laser Melted at Cryogenic Conditions, Manuf. Eng., 2006, 18(1), p 423–426

19.

J.M. Robinson, B.A. Van Brussel, J.T.M. De Hosson and R.C. Reed, X-Ray Measurement of Residual Stresses in Laser Surface Melted Ti-6Al-4V Alloy, Mater. Sci. Eng. A, 1996, 208(1), p 143–147. https://doi.org/10.1016/0921-5093(95)10158-6CrossRef

20.

G.Q. Wu, G.X. Luo, Z. Huang and Z.J. Ruan, Dendritic Structural Transformation of Laser Surface Remelted γ-TiAl Based Alloy during Post-Heat Treatment, Mater. Lett., 2006, 60(3), p 406–409. https://doi.org/10.1016/j.matlet.2005.09.001CrossRef

21.

B. Cárcel, A. Serrano, J. Zambrano, V. Amigó, and A.C. Cárcel, Laser Cladding of TiAl Intermetallic Alloy on Ti6Al4V. Process Optimization and Properties, Phys. Procedia, Elsevier B.V., 2014, 56(C), p 284–293. https://doi.org/10.1016/j.phpro.2014.08.173

22.

V.K. Balla, M. Das, A. Mohammad and A.M. Al-Ahmari, Additive Manufacturing of γ-TiAl: Processing, Microstructure, and Properties, Adv. Eng. Mater., 2016, 18(7), p 1208–1215. https://doi.org/10.1002/adem.201500588CrossRef

23.

V.K. Balla, J. Soderlind, S. Bose and A. Bandyopadhyay, Microstructure, Mechanical and Wear Properties of Laser Surface Melted Ti6Al4V Alloy, J. Mech. Behav. Biomed. Mater., 2014, 32, p 335–344. https://doi.org/10.1016/j.jmbbm.2013.12.001CrossRef

24.

G.V.K. Pradeep, M. Duraiselvam, K.S. Prasad, and A. Mohammad, Tribological Behavior of Additive Manufactured γ-TiAl by Electron Beam Melting, Trans. Indian Inst. Met., Springer India, 2020, 73(6), p 1661–1667. https://doi.org/10.1007/s12666-020-01950-8

25.

Standard test method for wear testing with a pin-on-disk apparatus, ASTM Standard, G 99

26.

M. Lamirand, J.L. Bonnentien, G. Ferrière, S. Guérin, and J.P. Chevalier, Effects of Interstitial Oxygen on Microstructure and Mechanical Properties of Ti-48AI-2Cr-2Nb with Fully Lamellar and Duplex Microstructures, Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2006, 37(8), p 2369–2378. https://doi.org/10.1007/BF02586211

27.

A. Mohammad, A.M. Alahmari, M.K. Mohammed, R.K. Renganayagalu and K. Moiduddin, Effect of Energy Input on Microstructure and Mechanical Properties of Titanium Aluminide Alloy Fabricated by the Additive Manufacturing Process of Electron Beam Melting, Materials (Basel), 2017, 10(2), p 1–16. https://doi.org/10.3390/ma10020211CrossRef

28.

J. Schwerdtfeger and C. Körner, Selective Electron Beam Melting of Ti-48Al-2Nb-2Cr: Microstructure and Aluminium Loss, Intermetallics, Elsevier Ltd, 2014, 49, p 29–35. https://doi.org/10.1016/j.intermet.2014.01.004CrossRef

29.

N. Jeyaprakash, C.-H. Yang and D.R. Kumar, Laser Surface Modification of Materials, Laser Ablation, 2020 https://doi.org/10.5772/intechopen.94439CrossRef

30.

F.H. Froes, C. Suryanarayana and D. Eliezer, Synthesis, Properties and Applications of Titanium Aluminides, J. Mater. Sci., 1992, 27(19), p 5113–5140. https://doi.org/10.1007/BF02403806CrossRef

31.

V.P. Rotshtein and V.A. Shulov, Surface Modification and Alloying of Aluminum and Titanium Alloys with Low-Energy, High-Current Electron Beams, J. Metall., 2011, p 1–15. https://doi.org/10.1155/2011/673685

32.

I.N. Maliutina, H. Si-Mohand, R. Piolet, F. Missemer, A.I. Popelyukh, N.S. Belousova, and P. Bertrand, Laser Cladding of γ-TiAl Intermetallic Alloy on Titanium Alloy Substrates, Metall. Mater. Trans. A Phys. Metall. Mater. Sci., Springer US, 2016, 47(1), p 378–387. https://doi.org/10.1007/s11661-015-3205-9

33.

M. Balichakra, S. Bontha, P. Krishna, V. K. Balla, Mater. Res. Express, Laser Surface Melting of γ-TiAl Alloy: An Experimental and Numerical Modeling Study, Materials research express, 2019 , 6(4), p 046543. https://doi.org/10.1088/2053-1591/aafc89

34.

N. Jeyaprakash, M. Duraiselvam and R. Raju, Modelling of Cr3C2-25% NiCr Laser Alloyed Cast Iron in High Temperature Sliding Wear Condition Using Response Surface Methodology, Arch. Metall. Mater., 2018, 63(3), p 1303–1315. https://doi.org/10.24425/123805CrossRef

Titel: Tribological Behavior of Laser Surface Melted γ-TiAl Fabricated by Electron Beam Additive Manufacturing
verfasst von: G. V. Krishna Pradeep
Muthukannan Duraiselvam
K. Sivaprasad
Publikationsdatum: 04.10.2021
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 2/2022
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-021-06278-y

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 2/2022

Experimental and Numerical Study on Ductile Fracture Prediction of Aluminum Alloy 6016-T6 Sheets Using a Phenomenological Model

Effect of Temperature on Metallurgical Reactions and Microstructure Evolution of 316L/BNi-2 Brazed Joints

Fabrication and Characterization of Nickel Microtubes through Electroforming: Deposition Optimization Using Evolutionary Algorithms

Effect of Magnetic-Mechanical Coupled Stirring on the Distribution of B4C Particles in Al-B4C Composites

Comparative Study on Tribological Behaviors of Two TiZr-Based Alloys in Vacuum

Effect of Different Yield Criteria and Material Parameter Identification Methods on the Description Accuracy of the Anisotropic Behavior of 5182-O Aluminum Alloy

Premium Partner

Marktübersichten