nach oben

Journal of Materials Engineering and Performance

Erschienen in:

15.03.2022 | Technical Article

Residual Stress Distribution, Phase Transformation, and Wettability Characteristics of Laser Peened Austenitic Stainless Steel

verfasst von: K. Praveenkumar, S. Swaroop, Geetha Manivasagam

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 8/2022

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Laser peening without protective coating (LPwC) has been performed on austenitic stainless steel (SS304) with a power density of 9 GW cm⁻² and peening passes of one, three and five. Effect of single and multiple laser peening on the residual stress distribution, work-hardening, surface roughness, phase transformation, and wettability has been studied using XRD, EBSD, surface profilometer and goniometer. A maximum compressive residual stress of - 581 MPa and work hardening depth that extended beyond 500 μm were observed with 5 peening passes. Further, an increase in austenite to martensite transformation (γ → α′) from 9.4 (unpeened) to 18.5% was observed for 5 peening passes. The average grain size reduced to 11.53% for five-time peened samples compared to single-time peened samples. Wettability studies revealed hydrophilic to hydrophobic transformation after laser peening.

Vorheriger Artikel Effect of Ti Content on Microstructure and Mechanical Properties of Mg-Sn Alloys Produced by Casting and Hot Extrusion

Nächster Artikel Experimental and Numerical Investigation of Stress and Distortion in AF1410 Steel Under Varying Quenching Conditions

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

A.P. Mouritz, Steels for Aircraft Structures, Introduction to Aerospace Materials, Elsevier, 2012, p 232-250CrossRef

Q. Lu, Q. Su, F. Wang, C. Zhang, Y. Lu, M. Nastasi and B. Cui, Influence of Laser Shock Peening on Irradiation Defects in Austenitic Stainless Steels, J. Nucl. Mater., 2017, 489, p 203-210. https://doi.org/10.1016/j.jnucmat.2017.03.046CrossRef

P. Yella, P. Venkateswarlu, R.K. Buddu, N. Ravi, K.B.S. Rao, P.P. Kiran and K.V. Rajulapati, Role of Sacrificial Layers on Surface Characteristics of Laser Shock Peened SS304 Plates, Opt. Laser Technol., 2018, 107, p 142-149. https://doi.org/10.1016/j.optlastec.2018.05.018CrossRef

R. Andersson, E. Schedin, C. Magnusson, J. Ocklund, and A. Persson, Stainless Steel Components in Automotive Vehicles, in Proceedings of the 4th Stainless Steel Science & Market Congress, 2002, 16(1), p 57. http://urn.kb.se/resolve?urn=urn:nbn:se:ltu:diva-6438

S. Bagheri and M. Guagliano, Review of Shot Peening Processes to Obtain Nanocrystalline Surfaces in Metal Alloys, Surf. Eng., 2009, 25(1), p 3-14.CrossRef

L. Xie, Y. Wen, K. Zhan, L. Wang, C. Jiang and V. Ji, Characterization on Surface Mechanical Properties of Ti-6Al-4V after Shot Peening, J. Alloys Compd., 2016, 666, p 65-70.CrossRef

S. Yang, W. Zeng and J. Yang, Characterization of Shot Peening Properties and Modelling on the Fatigue Performance of 304 Austenitic Stainless Steel, Int. J. Fatigue, 2020, 137, p 105621.CrossRef

S. Pour-Ali, A.R. Kiani-Rashid and A. Babakhani, Surface Nanocrystallization and Gradient Microstructural Evolutions in the Surface Layers of 321 Stainless Steel Alloy Treated via Severe Shot Peening, Vacuum, 2017, 144, p 152-159. https://doi.org/10.1016/j.vacuum.2017.07.016CrossRef

C.S. Montross, T. Wei, L. Ye, G. Clark and Y.W. Mai, Laser Shock Processing and Its Effects on Microstructure and Properties of Metal Alloys: A Review, Int. J. Fatigue, 2002, 24(10), p 1021-1036.CrossRef

10.

A.K. Gujba and M. Medraj, Laser Peening Process and Its Impact on Materials Properties in Comparison with Shot Peening and Ultrasonic Impact Peening, Materials, 2014, 7, p 7925-7974.CrossRef

11.

A.H. Clauer, Laser Shock Peening, the Path to Production, Metals (Basel), 2019, 9(6), p 626.CrossRef

12.

B. Dhakal and S. Swaroop, Review: Laser Shock Peening as Post Welding Treatment Technique, J. Manuf. Process., 2018, 32(April), p 721-733. https://doi.org/10.1016/j.jmapro.2018.04.006CrossRef

13.

W. Jia, Y. Zan, C. Mao, S. Li, W. Zhou, Q. Li, S. Zhang and V. Ji, Microstructure Evolution and Mechanical Properties of a Lamellar Near-α Titanium Alloy Treated by Laser Shock Peening, Vacuum, 2021, 184(Nonember 2020), p 109906. https://doi.org/10.1016/j.vacuum.2020.109906CrossRef

14.

I. Altenberger, R.K. Nalla, Y. Sano, L. Wagner and R.O. Ritchie, On the Effect of Deep-Rolling and Laser-Peening on the Stress-Controlled Low- and High-Cycle Fatigue Behavior of Ti-6Al-4V at Elevated Temperatures up to 550 °C, Int. J. Fatigue, 2012, 44, p 292-302.CrossRef

15.

E. Maawad, Y. Sano, L. Wagner, H.G. Brokmeier and C. Genzel, Investigation of Laser Shock Peening Effects on Residual Stress State and Fatigue Performance of Titanium Alloys, Mater. Sci. Eng. A, 2012, 536, p 82-91.CrossRef

16.

P.K. Rai, V. Pandey, K. Chattopadhyay, L.K. Singhal and V. Singh, Effect of Ultrasonic Shot Peening on Microstructure and Mechanical Properties of High-Nitrogen Austenitic Stainless Steel, J. Mater. Eng. Perform., 2014, 23(11), p 4055-4064.CrossRef

17.

Y. Feng, S. Hu, D. Wang and H. Zhang, Influence of Surface Topography and Needle Size on Surface Quality of Steel Plates Treated by Ultrasonic Peening, Vacuum, 2016, 132, p 22-30. https://doi.org/10.1016/j.vacuum.2016.07.021CrossRef

18.

J. Li, A. Feng, J. Zhou, H. Chen, Y. Sun, X. Tian, Y. Huang and S. Huang, Enhancement of Fatigue Properties of 2024-T351 Aluminum Alloy Processed by Cryogenic Laser Peening, Vacuum, 2019, 164(February), p 41-45. https://doi.org/10.1016/j.vacuum.2019.02.030CrossRef

19.

U. Trdan, M. Skarba and J. Grum, Laser Shock Peening Effect on the Dislocation Transitions and Grain Refinement of Al-Mg-Si Alloy, Mater. Charact., 2014, 97, p 57-68. https://doi.org/10.1016/j.matchar.2014.08.020CrossRef

20.

J.Z. Lu, K.Y. Luo, Y.K. Zhang, C.Y. Cui, G.F. Sun, J.Z. Zhou, L. Zhang, J. You, K.M. Chen and J.W. Zhong, Grain Refinement of LY2 Aluminum Alloy Induced by Ultra-High Plastic Strain during Multiple Laser Shock Processing Impacts, Acta Mater., 2010, 58(11), p 3984-3994.CrossRef

21.

C. Wang, L. Wang, C.L. Wang, K. Li and X.G. Wang, Dislocation Density-Based Study of Grain Refinement Induced by Laser Shock Peening, Opt. Laser Technol., 2020, 121, p 105827.CrossRef

22.

J.E. Masse and G. Barreau, Surface Modification by Laser Induced Shock Waves, Surf. Eng., 1995, 11(2), p 131-132.CrossRef

23.

L. Zhou, Y. Li, W. He, D. Chen and X. Nie, Effect of Multiple Laser Shock Processing on Microstructure and Mechanical Properties of Ti-5Al-4Mo-4Cr-2Sn-2Zr Titanium Alloy, Xiyou Jinshu Cailiao Yu Gongcheng/Rare Met. Mater. Eng., 2014, 43(5), p 1067-1072.

24.

X. Shen, P. Shukla, S. Nath and J. Lawrence, Improvement in Mechanical Properties of Titanium Alloy (Ti-6Al-7Nb) Subject to Multiple Laser Shock Peening, Surf. Coat. Technol., 2017, 327, p 101-109.CrossRef

25.

R. Sundar, H. Kumar, R. Kaul, K. Ranganathan, P. Tiwari, L.M. Kukreja and S.M. Oak, Studies on Laser Peening Using Different Sacrificial Coatings, Surf. Eng., 2012, 28(8), p 564-568.CrossRef

26.

N. Mukai, N. Aoki, M. Obata, A. Ito, Y. Sano, and C. Konagai, Laser Processing for Underwater Maintenance in Nuclear Plants, in 3rd JSME/ASME Joint International Conference on Nuclear Engineering, 1995, p 1489-1494. https://inis.iaea.org/search/search.aspx?orig_q=RN:38008928. Accessed 11 March 2020

27.

Y. Sano, K. Akita, K. Masaki, Y. Ochi, I. Altenberger and B. Scholtes, Laser Peening Without Coating as a Surface Enhancement Technology, J. Laser Micro Nanoeng., 2006, 1(3), p 161-166.CrossRef

28.

B. Sarre, S. Flouriot, G. Geandier, B. Panicaud and V. De Rancourt, Mechanical Behavior and Fracture Mechanisms of Titanium Alloy Welded Joints Made by Pulsed Laser Beam Welding, Proc. Struct. Integr., 2016, 2, p 3569-3576.

29.

Y. Sano, K. Masaki, T. Gushi and T. Sano, Improvement in Fatigue Performance of Friction Stir Welded A6061-T6 Aluminum Alloy by Laser Peening Without Coating, Mater. Des., 2012, 36, p 809-814. https://doi.org/10.1016/j.matdes.2011.10.053CrossRef

30.

D. Kumar, S. Nadeem Akhtar, A. Kumar Patel, J. Ramkumar and K. Balani, Tribological Performance of Laser Peened Ti-6Al-4V, Wear, 2015, 322-323, p 203-217.CrossRef

31.

U. Trdan and J. Grum, SEM/EDS Characterization of Laser Shock Peening Effect on Localized Corrosion of Al Alloy in a Near Natural Chloride Environment, Corros. Sci., 2014, 82, p 328-338.CrossRef

32.

P. Peyre, R. Fabbro, P. Merrien and H.P. Lieurade, Laser Shock Processing of Aluminium Alloys. Application to High Cycle Fatigue Behaviour, Mater. Sci. Eng. A, 1996, 210(1-2), p 102-113.CrossRef

33.

A.H. Clauer and D.F. Lahrman, Laser Shock Processing as a Surface Enhancement Process, Key Eng. Mater., 2001, 197, p 121-142.CrossRef

34.

C. Wang, L. Wang, C.L. Wang, K. Li and X.G. Wang, Dislocation Density-Based Study of Grain Refinement Induced by Laser Shock Peening, Opt. Laser Technol., 2019, 2020, p 121.

35.

H. Ding and Y.C. Shin, Dislocation Density-Based Modeling of Subsurface Grain Refinement with Laser-Induced Shock Compression, Comput. Mater. Sci., 2012, 53(1), p 79-88.CrossRef

36.

A. Umapathi and S. Swaroop, Residual Stress Distribution in a Laser Peened Ti-2.5Cu Alloy, Surf. Coat. Technol., 2016, 307, p 38-46. https://doi.org/10.1016/j.surfcoat.2016.08.053CrossRef

37.

D. Karthik, K.U. Yazar, A. Bisht, S. Swaroop, C. Srivastava and S. Suwas, Gradient Plastic Strain Accommodation and Nanotwinning in Multi-pass Laser Shock Peened 321 Steel, Appl. Surf. Sci., 2019, 487(May), p 426-432. https://doi.org/10.1016/j.apsusc.2019.05.130CrossRef

38.

O. Hatamleh and A. DeWald, An Investigation of the Peening Effects on the Residual Stresses in Friction Stir Welded 2195 and 7075 Aluminum Alloy Joints, J. Mater. Process. Technol., 2009, 209(10), p 4822-4829.CrossRef

39.

H. Chen, A. Feng, J. Li, T. Jia and Y. Liu, Effects of Multiple Laser Peening Impacts on Mechanical Properties and Microstructure Evolution of 40CrNiMo Steel, J. Mater. Eng. Perform., 2019, 28(5), p 2522-2529. https://doi.org/10.1007/s11665-019-04034-xCrossRef

40.

X.C. Zhang, Y.K. Zhang, J.Z. Lu, F.Z. Xuan, Z.D. Wang and S.T. Tu, Improvement of Fatigue Life of Ti-6Al-4V Alloy by Laser Shock Peening, Mater. Sci. Eng. A, 2010, 527(15), p 3411-3415. https://doi.org/10.1016/j.msea.2010.01.076CrossRef

41.

J. Li, J. Zhou, A. Feng, S. Huang, X. Meng, Y. Sun, Y. Huang and X. Tian, Influence of Multiple Laser Peening on Vibration Fatigue Properties of TC6 Titanium Alloy, Opt. Laser Technol., 2019, 118, p 183-191.CrossRef

42.

J.Z. Lu, K.Y. Luo, Y.K. Zhang, G.F. Sun, Y.Y. Gu, J.Z. Zhou, X.D. Ren, X.C. Zhang, L.F. Zhang, K.M. Chen, C.Y. Cui, Y.F. Jiang, A.X. Feng and L. Zhang, Grain Refinement Mechanism of Multiple Laser Shock Processing Impacts on ANSI 304 Stainless Steel, Acta Mater., 2010, 58(16), p 5354-5362.CrossRef

43.

C. Ye, S. Suslov, D. Lin and G.J. Cheng, Deformation-Induced Martensite and Nanotwins by Cryogenic Laser Shock Peening of AISI 304 Stainless Steel and the Effects on Mechanical Properties, Philos. Mag., 2012, 92(11), p 1369-1389.CrossRef

44.

Y. Yang, X. Lian, K. Zhou and G. Li, Effects of Laser Shock Peening on Microstructures and Properties of 2195 Al-Li Alloy, J. Alloys Compd., 2019, 781, p 330-336. https://doi.org/10.1016/j.jallcom.2018.12.118CrossRef

45.

S. Sathyajith, S. Kalainathan and S. Swaroop, Laser Shot Peening of 304 Austenitic Stainless Steel Without Protective Coating, Mater. Sci. Forum, 2011, 699, p 131-140.CrossRef

46.

Y. Sano, M. Obata, T. Kubo, N. Mukai, M. Yoda, K. Masaki and Y. Ochi, Retardation of Crack Initiation and Growth in Austenitic Stainless Steels by Laser Peening Without Protective Coating, Mater. Sci. Eng. A, 2006, 417(1-2), p 334-340.CrossRef

47.

I. Nikitin, B. Scholtes, H.J. Maier and I. Altenberger, High Temperature Fatigue Behavior and Residual Stress Stability of Laser-Shock Peened and Deep Rolled Austenitic Steel AISI 304, Scr. Mater., 2004, 50(10), p 1345-1350.CrossRef

48.

Z. Lu, F. Xu, C. Tang, Y. Cui, H. Xu and J. Mao, Stress Corrosion Cracking Susceptibility of 304 Stainless Steel Subjected to Laser Shock Peening Without Coating, J. Mater. Eng. Perform., 2021 https://doi.org/10.1007/s11665-021-05898-8CrossRef

49.

A. Nakajima, K. Hashimoto and T. Watanabe, Recent Studies on Super-Hydrophobic Films, Monatshefte für Chemie/Chem. Mon., 2001, 132(1), p 31-41. https://doi.org/10.1007/s007060170142CrossRef

50.

Y.B. Wang, H.F. Li, Y.F. Zheng, S.C. Wei and M. Li, Correlation Between Corrosion Performance and Surface Wettability in ZrTiCuNiBe Bulk Metallic Glasses, Appl. Phys. Lett., 2010, 96(25), p 8-11.

51.

T. Sasaki, M. Shin-ya, S. Mitsui, R. Nishimura, K. Yanagi, T. Miyoshi and Y. Arai, X-ray Tri-Axial Stress Analysis System Using Two Monolithic SOI Pixel Detectors, Nucl. Instrum. Methods Phys. Res. section A Accel. Spectrom. Detect. Assoc. Equip., 2020, 979, p 164426.CrossRef

52.

K.Y. Luo, J.Z. Lu, Y.K. Zhang, J.Z. Zhou, L.F. Zhang, F.Z. Dai, L. Zhang, J.W. Zhong and C.Y. Cui, Effects of Laser Shock Processing on Mechanical Properties and Micro-structure of ANSI 304 Austenitic Stainless Steel, Mater. Sci. Eng. A, 2011, 528(13-14), p 4783-4788.CrossRef

53.

P.R. Smith, M.J. Shepard, P.S. Prevéy and A.H. Clauer, Effect of Power Density and Pulse Repetition on Laser Shock Peening of Ti-6Al-4V, J. Mater. Eng. Perform., 2000, 9(1), p 33-37.CrossRef

54.

Z. Tong, X. Ren, Y. Ren, F. Dai, Y. Ye, W. Zhou, L. Chen and Z. Ye, Effect of Laser Shock Peening on Microstructure and Hot Corrosion of TC11 Alloy, Surf. Coat. Technol., 2018, 335, p 32-40.CrossRef

55.

D. Karthik and S. Swaroop, Laser Peening without Coating Induced Phase Transformation and Thermal Relaxation of Residual Stresses in AISI 321 Steel, Surf. Coat. Technol., 2016, 291, p 161-171. https://doi.org/10.1016/j.surfcoat.2016.02.038CrossRef

56.

B.D. Cullity, Elements of X-ray Diffraction, Addison Wesley Publishing, Reading, MA, 1956, p 99

57.

E. Nagy, V. Mertinger, F. Tranta and J. Sólyom, Deformation Induced Martensitic Transformation in Stainless Steels, Mater. Sci. Eng. A, 2004, 378(1-2 SPEC. ISS.), p 308-313.CrossRef

58.

A.K. De, D.C. Murdock, M.C. Mataya, J.G. Speer and D.K. Matlock, Quantitative Measurement of Deformation-Induced Martensite in 304 Stainless Steel by X-ray Diffraction, Scr. Mater., 2004, 50(12), p 1445-1449.CrossRef

59.

Y.F. Shen, X.X. Li, X. Sun, Y.D. Wang and L. Zuo, Twinning and Martensite in a 304 Austenitic Stainless Steel, Mater. Sci. Eng. A, 2012, 552, p 514-522.CrossRef

60.

M. Turski, S. Clitheroe, A.D. Evans, C. Rodopoulos, D.J. Hughes and P.J. Withers, Engineering the Residual Stress State and Microstructure of Stainless Steel with Mechanical Surface Treatments, Appl. Phys. A Mater. Sci. Process., 2010, 99(3), p 549-556.CrossRef

61.

M. Gerland and M. Hallouin, Effect of Pressure on the Microstructure of an Austenitic Stainless Steel Shock-Loaded by Very Short Laser Pulses, J. Mater. Sci., 1994, 29(2), p 345-351.CrossRef

62.

I. Nikitin and I. Altenberger, Comparison of the Fatigue Behavior and Residual Stress Stability of Laser-Shock Peened and Deep Rolled Austenitic Stainless Steel AISI 304 in the Temperature Range 25-600 °C, Mater. Sci. Eng. A, 2007, 465(1-2), p 176-182.CrossRef

63.

B.N. Mordyuk, Y.V. Milman, M.O. Iefimov, G.I. Prokopenko, V.V. Silberschmidt, M.I. Danylenko and A.V. Kotko, Characterization of Ultrasonically Peened and Laser-Shock Peened Surface Layers of AISI 321 Stainless Steel, Surf. Coat. Technol., 2008, 202(19), p 4875-4883.CrossRef

64.

S. Kalainathan, S. Sathyajith and S. Swaroop, Effect of Laser Shot Peening Without Coating on the Surface Properties and Corrosion Behavior of 316L Steel, Opt. Lasers Eng., 2012, 50(12), p 1740-1745. https://doi.org/10.1016/j.optlaseng.2012.07.007CrossRef

65.

P. Peyre, X. Scherpereel, L. Berthe, C. Carboni, R. Fabbro, G. Béranger and C. Lemaitre, Surface Modifications Induced in 316L Steel by Laser Peening and Shot-Peening. Influence on Pitting Corrosion Resistance, Mater. Sci. Eng. A, 2000, 280(2), p 294-302.CrossRef

66.

B. Dhakal and S. Swaroop, Effect of Laser Shock Peening on Mechanical and Microstructural Aspects of 6061-T6 Aluminum Alloy, J. Mater. Process. Technol., 2020, 282, p 116640.CrossRef

67.

G.E. Dieter, Mechanical Metallurgy, McGRAW-Hill Book Company, New York, 1961, p 447-459

68.

L. Zhou, W. He, S. Luo, C. Long, C. Wang, X. Nie, G. He, X. Shen and Y. Li, Laser Shock Peening Induced Surface Nanocrystallization and Martensite Transformation in Austenitic Stainless Steel, J. Alloys Compd., 2016, 655, p 66-70. https://doi.org/10.1016/j.jallcom.2015.06.268CrossRef

69.

K.Y. Luo, H.X. Yao, F.Z. Dai and J.Z. Lu, Surface Textural Features and Its Formation Process of AISI 304 Stainless Steel Subjected to Massive LSP Impacts, Opt. Lasers Eng., 2014, 55, p 136-142.CrossRef

70.

M.J.J.P.T. NovelliFundenbergerBocherGrosdidier, On the Effectiveness of Surface Severe Plastic Deformation by Shot Peening at Cryogenic Temperature, Appl. Surf. Sci., 2016, 389, p 1169-1174.CrossRef

71.

Y. Zou, Z. Sang, Q. Wang, T. Li, D. Li and Y. Li, Improving the Mechanical Properties of 304 Stainless Steel Using Waterjet Peening, Medziagotyra, 2020, 26(2), p 161-167.

72.

S. Prabhakaran, A. Kulkarni, G. Vasanth, S. Kalainathan, P. Shukla and V.K. Vasudevan, Laser Shock Peening Without Coating Induced Residual Stress Distribution, Wettability Characteristics and Enhanced Pitting Corrosion Resistance of Austenitic Stainless Steel, Appl. Surf. Sci., 2018, 428, p 17-30. https://doi.org/10.1016/j.apsusc.2017.09.138CrossRef

73.

B.S. Yilbas, H. Ali, A. Al-Sharafi and H. Al-Qahtani, Laser Processing of Ti6Al4V Alloy: Wetting State of Surface and Environmental Dust Effects, Heliyon, 2019, 5(2), p e01211.CrossRef

74.

P. Peyre, C. Carboni, A. Sollier, L. Berthe, C. Richard, E. de Los Rios and R. Fabbro, New Trends in Laser Shock Wave Physics and Applications, High-Power Laser Ablation IV, 2002, 4760, p 654-666.CrossRef

75.

P. Peyre, C. Carboni, P. Forget, G. Beranger, C. Lemaitre and D. Stuart, Influence of Thermal and Mechanical Surface Modifications Induced by Laser Shock Processing on the Initiation of Corrosion Pits in 316L Stainless Steel, J. Mater. Sci., 2007, 42(16), p 6866-6877.CrossRef

76.

D. Karthik and S. Swaroop, Laser Shock Peening Enhanced Corrosion Properties in a Nickel Based Inconel 600 Superalloy, J. Alloys Compd., 2017, 694, p 1309-1319.CrossRef

77.

M.A. Meyers, Microstructural Evolution in Adiabatic Shear Localization in Stainless Steel, Acta Mater., 2003, 571, p 571-574.

78.

V.K. Caralapatti and S. Narayanswamy, Analyzing the Effect of High Repetition Laser Shock Peening on Dynamic Corrosion Rate of Magnesium, Opt. Laser Technol., 2017, 93, p 165-174. https://doi.org/10.1016/j.optlastec.2017.02.010CrossRef

Titel: Residual Stress Distribution, Phase Transformation, and Wettability Characteristics of Laser Peened Austenitic Stainless Steel
verfasst von: K. Praveenkumar
S. Swaroop
Geetha Manivasagam
Publikationsdatum: 15.03.2022
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 8/2022
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-022-06748-x

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 8/2022

Microstructure and Mechanical Properties of a High-Ductility Al-Zn-Mg-Cu Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing

Grain Refinement Behavior of Accumulative Roll Bonding-Processed Mg-14Li-3Al-2Gd Alloy

Corrosion Law of Q345 Steel Pipe when Transporting Tailings Paste Slurry

Effect of Post Processes on Mechanical Properties of 3D Printed Ti6Al4V Gears

A New Ductile Fracture Model for Edge Cracking Prediction of Ultra-High Strength Steel Considering Damage Accumulation in Blanking Process

Statistical Analysis of Clad Geometry in Direct Energy Deposition of Inconel 718 Single Tracks

Premium Partner

Marktübersichten