Skip to main content
Fachgebiete
Automobil + Motoren Bauwesen + Immobilien Business IT + Informatik Elektrotechnik + Elektronik Energie + Nachhaltigkeit Finance + Banking Management + Führung Marketing + Vertrieb Maschinenbau + Werkstoffe Versicherung + Risiko
DE
EN
Bücher
Zeitschriften
Themenseiten
Organisationspsychologie Projektmanagement Marketing Smart Manufacturing
Weitere Formate
Podcasts Webinare Technik Webinare Wirtschaft Kongresse Veranstaltungskalender Awards
Jetzt Einzelzugang starten
Zugang für Unternehmen
Referenzkunden
SLX-Digitalkonferenz: Zukunftswerkstatt 2024

Mehr Umsatz mit Top-Kontakten

Am 7. Mai erfahren Sie, wie Vertriebsteams Leadgenerierung, Leadnurturing und Leadstrategien effizient steuern können.
Erweiterte Suche
Anmelden
nach oben
Journal of Materials Science
Erschienen in: Journal of Materials Science 1/2018

05.09.2017 | Ceramics

Robocasting of dense yttria-stabilized zirconia structures

verfasst von: Erwin Peng, Xiangxia Wei, Ulf Garbe, Dehong Yu, Brunet Edouard, Aihong Liu, Jun Ding

Erschienen in: Journal of Materials Science | Ausgabe 1/2018

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config
loading …

Abstract

Advanced ceramic materials with complex design have become inseparable from the current engineering applications. Due to the limitation of traditional ceramic processing, ceramic additive manufacturing (AM) which allows high degree of fabrication freedom has gained significant research interest. Among these AM techniques, low-cost robocasting technique is often considered to fabricate complex ceramic components. In this work, aqueous ceramic suspension comprising of commercial nano-sized yttria-stabilized zirconia (YSZ) powder has been developed for robocasting purpose. Both fully and partially stabilized YSZ green bodies with complex morphologies were successfully printed in ambient conditions using relatively low-solid-content ceramic suspensions (<38 vol%). The sintered structures were able to retain the original morphologies with >94% of the theoretical density despite its high linear shrinkage (up to 33%). The microstructure analysis indicated that dense fully and partially stabilized YSZ with grain size as small as 1.40 ± 0.53 and 0.38 ± 0.10 μm can be obtained, respectively. The sintered partially stabilized YSZ solid and porous mesh samples (porosity of macro-pores >45%) exhibited hardness up to 13.29 GPa and flexural strengths up to 242.8 ± 11.4 and 57.3 ± 5.2 MPa, respectively. The aqueous-based ceramic suspension was also demonstrated to be suitable for the fabrication of large YSZ parts with good repeatability.
Vorheriger Artikel Synthesis and characterization of mechanically strong carboxymethyl cellulose–gelatin–hydroxyapatite nanocomposite for load-bearing orthopedic application
Nächster Artikel Synthesis, microstructure, and electrical behavior of (Na0.5Bi0.5)0.94Ba0.06TiO3 piezoelectric ceramics via a citric acid sol–gel method

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

  • über 102.000 Bücher
  • über 537 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Finance + Banking
  • Management + Führung
  • Marketing + Vertrieb
  • Maschinenbau + Werkstoffe
  • Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

  • über 67.000 Bücher
  • über 390 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Maschinenbau + Werkstoffe




 

Jetzt Wissensvorsprung sichern!

Jetzt informieren
Anhänge
Nur mit Berechtigung zugänglich
Literatur
1.
Belmonte M (2006) Advanced ceramic materials for high temperature applications. Adv Eng Mater 8(8):693–703CrossRef
2.
Kelly JR, Denry I (2008) Stabilized zirconia as a structural ceramic: an overview. Dent Mater 24(3):289–298CrossRef
3.
Gautam C, Joyner J, Gautam A, Rao J, Vajtai R (2016) Zirconia based dental ceramics: structure, mechanical properties, biocompatibility and applications. Dalton Trans 45(48):19194–19215CrossRef
4.
Park J-S, Kim H, Kim I-D (2014) Overview of electroceramic materials for oxide semiconductor thin film transistors. J Electroceram 32(2):117–140CrossRef
5.
Schlordt T, Schwanke S, Keppner F, Fey T, Travitzky N, Greil P (2013) Robocasting of alumina hollow filament lattice structures. J Eur Ceram Soc 33(15–16):3243–3248CrossRef
6.
Manicone PF, Rossi Iommetti P, Raffaelli L (2007) An overview of zirconia ceramics: basic properties and clinical applications. J Dent 35(11):819–826CrossRef
7.
Zhao S, Xiao W, Rahaman MN, O’Brien D, Seitz-Sampson JW, Sonny Bal B (2017) Robocasting of silicon nitride with controllable shape and architecture for biomedical applications. Int J Appl Ceram Technol 14(2):117–127CrossRef
8.
Cai K, Román-Manso B, Smay JE, Zhou J, Osendi MI, Belmonte M, Miranzo P (2012) Geometrically complex silicon carbide structures fabricated by robocasting. J Am Ceram Soc 95(8):2660–2666CrossRef
9.
Chen Z, Song X, Lei L, Chen X, Fei C, Chiu CT, Qian X, Ma T, Yang Y, Shung K, Chen Y, Zhou Q (2016) 3D printing of piezoelectric element for energy focusing and ultrasonic sensing. Nano Energy 27:78–86CrossRef
10.
Tuttle BA, Smay JE, Cesarano J, Voigt JA, Scofield TW, Olson WR, Lewis JA (2001) Robocast Pb(Zr0.95Ti0.05)O3 ceramic monoliths and composites. J Am Ceram Soc 84(4):872–874CrossRef
11.
Jakus AE, Taylor SL, Geisendorfer NR, Dunand DC, Shah RN (2015) Metallic architectures from 3D-printed powder-based liquid inks. Adv Func Mater 25(45):6985–6995CrossRef
12.
Wei X, Nagarajan RS, Peng E, Xue J, Wang J, Ding J (2016) Fabrication of YBa2Cu3O7−x (YBCO) superconductor bulk structures by extrusion freeforming. Ceram Int 42(14):15836–15842CrossRef
13.
Tsampas MN, Sapountzi FM, Vernoux P (2015) Applications of yttria stabilized zirconia (YSZ) in catalysis. Catal Sci Technol 5(11):4884–4900CrossRef
14.
Devi PS, Sharma AD, Maiti HS (2004) Solid oxide fuel cell materials: a review. Trans Indian Ceram Soc 63(2):75–98CrossRef
15.
Porter DL, Evans AG, Heuer AH (1979) Transformation-toughening in partially-stabilized zirconia (PSZ). Acta Metall 27(10):1649–1654CrossRef
16.
Durá OJ, López de la Torre MA, Vázquez L, Chaboy J, Boada R, Rivera-Calzada A, Santamaria J, Leon C (2010) Ionic conductivity of nanocrystalline yttria-stabilized zirconia: grain boundary and size effects. Phys Rev B 81(18):184301CrossRef
17.
Shanti NO, Hovis DB, Seitz ME, Montgomery JK, Baskin DM, Faber KT (2009) Ceramic laminates by gelcasting. Int J Appl Ceram Technol 6(5):593–606CrossRef
18.
Hotza D, Greil P (1995) Review: aqueous tape casting of ceramic powders. Mater Sci Eng A 202(1):206–217CrossRef
19.
Mohd Foudzi F, Muhamad N, Bakar Sulong A, Zakaria H (2013) Yttria stabilized zirconia formed by micro ceramic injection molding: rheological properties and debinding effects on the sintered part. Ceram Int 39(3):2665–2674CrossRef
20.
Lewis JA, Smay JE, Stuecker J, Cesarano J (2006) Direct ink writing of three-dimensional ceramic structures. J Am Ceram Soc 89(12):3599–3609CrossRef
21.
Travitzky N, Bonet A, Dermeik B, Fey T, Filbert-Demut I, Schlier L, Schlordt T, Greil P (2014) Additive manufacturing of ceramic-based materials. Adv Eng Mater 16(6):729–754CrossRef
22.
Zocca A, Colombo P, Gomes CM, Günster J (2015) Additive manufacturing of ceramics: issues, potentialities, and opportunities. J Am Ceram Soc 98(7):1983–2001CrossRef
23.
Qian B, Shen Z (2013) Laser sintering of ceramics. J Asian Ceram Soc 1(4):315–321CrossRef
24.
Manogharan G, Kioko M, Linkous C (2015) Binder jetting: a novel solid oxide fuel-cell fabrication process and evaluation. JOM 67(3):660–667CrossRef
25.
Halloran JW (2016) Ceramic stereolithography: additive manufacturing for ceramics by photopolymerization. Annu Rev Mater Res 46(1):19–40CrossRef
26.
Allahverdi M, Danforth SC, Jafari M, Safari A (2001) Processing of advanced electroceramic components by fused deposition technique. J Eur Ceram Soc 21(10–11):1485–1490CrossRef
27.
Lu X, Lee Y, Yang S, Hao Y, Evans JRG, Parini CG (2009) Fine lattice structures fabricated by extrusion freeforming: process variables. J Mater Process Technol 209(10):4654–4661CrossRef
28.
Maazouz Y, Montufar EB, Guillem-Marti J, Fleps I, Ohman C, Persson C, Ginebra MP (2014) Robocasting of biomimetic hydroxyapatite scaffolds using self-setting inks. J Mater Chem B 2(33):5378–5386CrossRef
29.
Mason MS, Huang T, Landers RG, Leu MC, Hilmas GE (2009) Aqueous-based extrusion of high solids loading ceramic pastes: process modeling and control. J Mater Process Technol 209(6):2946–2957CrossRef
30.
Scheithauer U, Schwarzer E, Richter H-J, Moritz T (2015) Thermoplastic 3D printing—an additive manufacturing method for producing dense ceramics. Int J Appl Ceram Technol 12(1):26–31CrossRef
31.
Vaidyanathan R, Walish J, Lombardi JL, Kasichainula S, Calvert P, Cooper KC (2000) The extrusion freeforming of functional ceramic prototypes. JOM 52(12):34–37CrossRef
32.
Leu MC, Deuser BK, Tang L, Landers RG, Hilmas GE, Watts JL (2012) Freeze-form extrusion fabrication of functionally graded materials. CIRP Ann Manuf Technol 61(1):223–226CrossRef
33.
de Hazan Y, Thänert M, Trunec M, Misak J (2012) Robotic deposition of 3d nanocomposite and ceramic fiber architectures via UV curable colloidal inks. J Eur Ceram Soc 32(6):1187–1198CrossRef
34.
Faes M, Valkenaers H, Vogeler F, Vleugels J, Ferraris E (2015) Extrusion-based 3D printing of ceramic components. Procedia CIRP 28:76–81CrossRef
35.
Feilden E, Blanca EG-T, Giuliani F, Saiz E, Vandeperre L (2016) Robocasting of structural ceramic parts with hydrogel inks. J Eur Ceram Soc 36(10):2525–2533CrossRef
36.
Lu X, Lee Y, Yang S, Hao Y, Ubic R, Evans JRG, Parini CG (2008) Fabrication of electromagnetic crystals by extrusion freeforming. Metamaterials 2(1):36–44CrossRef
37.
Lu X, Lee Y, Yang S, Hao Y, Evans JRG, Parini CG (2010) Solvent-based paste extrusion solid freeforming. J Eur Ceram Soc 30(1):1–10CrossRef
38.
Michna S, Wu W, Lewis JA (2005) Concentrated hydroxyapatite inks for direct-write assembly of 3-D periodic scaffolds. Biomaterials 26(28):5632–5639CrossRef
39.
Smay JE, Cesarano J, Lewis JA (2002) Colloidal inks for directed assembly of 3-D periodic structures. Langmuir 18(14):5429–5437CrossRef
40.
Garbe U, Randall T, Hughes C (2011) The new neutron radiography/tomography/imaging station DINGO at OPAL. Nucl Instrum Methods Phys Res Sect A 651(1):42–46CrossRef
41.
Lewis JA (2000) Colloidal processing of ceramics. J Am Ceram Soc 83(10):2341–2359CrossRef
42.
Moreno R (2012) Colloidal processing of ceramics and composites. Adv Appl Ceram 111(5-6):246–253CrossRef
43.
Hidber PC, Graule TJ, Gauckler LJ (1996) Citric acid—a dispersant for aqueous alumina suspensions. J Am Ceram Soc 79(7):1857–1867CrossRef
44.
Çınar S, Akinc M (2014) Ascorbic acid as a dispersant for concentrated alumina nanopowder suspensions. J Eur Ceram Soc 34(8):1997–2004CrossRef
45.
Stuecker JN, Cesarano Iii J, Hirschfeld DA (2003) Control of the viscous behavior of highly concentrated mullite suspensions for robocasting. J Mater Process Technol 142(2):318–325CrossRef
46.
Tekeli S (2007) The solid solubility limit of Al2O3 and its effect on densification and microstructural evolution in cubic-zirconia used as an electrolyte for solid oxide fuel cell. Mater Des 28(2):713–716CrossRef
47.
Tekeli S, Demir U (2005) Colloidal processing, sintering and static grain growth behaviour of alumina-doped cubic zirconia. Ceram Int 31(7):973–980CrossRef
48.
Houmard M, Fu Q, Genet M, Saiz E, Tomsia AP (2013) On the structural, mechanical, and biodegradation properties of HA/β-TCP robocast scaffolds. J Biomed Mater Res B Appl Biomater 101(7):1233–1242CrossRef
49.
Michorczyk P, Hedrzak E, Wegrzyniak A (2016) Preparation of monolithic catalysts using 3D printed templates for oxidative coupling of methane. J Mater Chem A 4(48):18753–18756CrossRef
50.
Metadaten
Titel
Robocasting of dense yttria-stabilized zirconia structures
verfasst von
Erwin Peng
Xiangxia Wei
Ulf Garbe
Dehong Yu
Brunet Edouard
Aihong Liu
Jun Ding
Publikationsdatum
05.09.2017
Verlag
Springer US
Erschienen in
Journal of Materials Science / Ausgabe 1/2018
Print ISSN: 0022-2461
Elektronische ISSN: 1573-4803
DOI
https://doi.org/10.1007/s10853-017-1491-x

Weitere Artikel der Ausgabe 1/2018

Journal of Materials Science 1/2018 Zur Ausgabe

Energy materials

Synthesis of poly(m-phenylenediamine)-coated hexagonal Co9S8 for high-performance supercapacitors

Polymers

Review: nanoparticles and nanostructured materials in papermaking

Ceramics

Investigation of earth-alkaline (EA = Mg, Ca, Sr) containing methylammonium tin iodide perovskite systems

Review

Review of recent achievements in self-healing conductive materials and their applications

Review

A review of soft errors and the low α-solder bumping process in 3-D packaging technology

Chemical routes to materials

A versatile and efficient method to fabricate recyclable superhydrophobic composites based on brucite and organosilane

Premium Partner

    Marktübersichten

    Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen. 

    Zur Marktübersicht
    Bildnachweise