nach oben

Journal of Materials Engineering and Performance

Erschienen in:

23.05.2022 | Technical Article

Effect of Electromagnetic Stirring Frequency on Inconel625-High Strength Low Alloy Steel Functionally Graded Material Fabricated by Wire Arc Additive Manufacturing

verfasst von: Jiarong Zhang, Xinjie Di, Chengning Li, Lingzhi Ba, Xing Jiang

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 12/2022

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The influences of electromagnetic stirring (EMS) at different frequencies on the formability, microstructure, mechanical properties and corrosion behavior of Inconel625-HSLA (high-strength low-alloy) steel functionally graded materials (FGMs) were studied. A wire arc additive manufacturing (WAAM) system with EMS at different frequencies was applied to fabricate the Inconel625-HSLA steel FGMs. The ratio of the maximum effective area (R_max) was used to illustrate the formability of the FGMs. The R_max of the FGMs was increased from 54.7 to 84.8% after EMS at a frequency of 4 Hz with an excitation current of 2 A. The tensile strength and microhardness were tested, and electrochemical tests were conducted to study the corrosion resistance of the FGMs. Compared to the FGM without EMS, the FGM fabricated in EMS at a frequency of 4 Hz and excitation current of 2 A had a primary dendrite spacing that was an average of 13.7% lower, an increased average tensile strength and microhardness (12.5 and 6.7%, respectively), and an increased the corrosion potential (E_corr), pitting potential (E_p) and passive region (ΔE); these values increased from − 186 to − 139 mV_SCE, from 299 to 477 mV_SCE and from 113 to 338 mV_SCE, respectively.

Vorheriger Artikel Effect of Hard Cyclic Viscoplastic Deformation on the Microstructure, Mechanical Properties, and Electrical Conductivity of Cu-Cr Alloy

Nächster Artikel Optimization of Welding Parameters During Ti-TA2/5A06Al Dissimilar Double-Sided Cold Arc Metal Inert Gas Welding

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

G.P. Dinda, A.K. Dasgupta, and J. Mazumder, Laser Aided Direct Metal Deposition of Inconel 625 Superalloy: Microstructure Evolution and Thermal Stability, Mater. Sci. Eng. A., 2009, 509(1–2), p 98–104. https://doi.org/10.1016/j.msea.2009.01.009CrossRef

T. Jacek, F. Dariusz, and R. Gregorz, Dissimilar Under water welding of HSLA steels, Int. J. Adv. Manuf. Technol., 2020 https://doi.org/10.1007/s00170-020-05617-yCrossRef

H. Vemanaboina, G. Edison, and S. Akella, Weld Bead Temperature and Residual Stresses Evaluations in Multipass Dissimilar INCONEL625 and SS316L by GTAW Using IR Thermography and X-ray Diffraction Techniques, Mater. Res. Exp., 2020 https://doi.org/10.1088/2053-1591/ab3298CrossRef

N.K. Adomako, H.J. Park, S.C. Cha, and Lee.M, Kim.J H., Microstructure Evolutin and Mechanical Properties of the Dissimilar Joint Between IN718 and STS304, Mater. Sci. Eng. A., 2021 https://doi.org/10.1016/j.msea.2020.140262CrossRef

J.M. Wilson and Y.C. Shin, Microstructure and Wear Properties of Laser-Deposited Functionally Graded Inconel 690 Reinforced with TiC, Surf. Coat. Technol., 2012, 207, p 517–522. https://doi.org/10.1016/j.surfcoat.2012.07.058CrossRef

H.P. Qu, P. Li, S.Q. Zhang, A. Li, and H.M. Wang, Microstructure and Mechanical Property of Lasermelting Deposition (LMD) Ti/TiAl Structural Gradient Material, Mater. Des., 2010, 31(1), p 128–134. https://doi.org/10.1016/j.matdes.2009.07.004CrossRef

C. Varun, N.M. Sai, K. Kumar, and Y, Srinivas A M, Sriswaroop D, Abhinav J, R.V. Ramanujan, R. Banerjee., Additive Manufacturing of Functionally Graded Co- Fe and Ni-Fe Magnetic Materials, J. Alloys Comp., 2020 https://doi.org/10.1016/j.jallcom.2020.153817CrossRef

Bo. Chen, Su. Yi, X. Zhouhong, T. Caiwang, and F. Jicai, Development and Characterization of 316L/Inconel625 Functionally Graded Material Fabricated by Laser Direct Metal Deposition, Opt. Laser Technol., 2020 https://doi.org/10.1016/j.optlastec.2019.105916CrossRef

Q. Jia and D. Gu, Selective Laser Melting Additive Manufacturing of Inconel 718 Superalloy Parts: Densification, Microstructure and Properties, J. Alloys Comp, 2013 https://doi.org/10.1016/j.jallcom.2013.09.171CrossRef

10.

P.L. Blackwell, The Mechanical and Microstructural Characteristics of Laser-Deposited IN718, J. Mater. Process. Technol., 2005, 170(1–2), p 240–246. https://doi.org/10.1016/j.jmatprotec.2005.5.008CrossRef

11.

C. Zhong, A. Gasser, J. Kittel, K. Wissenbach, and R. Poprawe, Improvement of Material Performance of Inconel 718 Formed by High Deposition-Rate Laser Metal Deposition, Mater. Des., 2016, 98, p 128–134. https://doi.org/10.1016/j.matdes.2016.03.006CrossRef

12.

T. Trosch, J. Strößner, R. Völkl, and U. Glatzel, Microstructure and Mechanical Properties of Selective Laser Melted Inconel 718 Compared to Forging and Casting, Mater. Lett., 2016, 164, p 428–431. https://doi.org/10.1016/j.matlet.2015.10.136CrossRef

13.

C. Shen, Z.X. Pan, Y. Ma, D. Cuiuri, and H.J. Li, Fabrication of Iron-Rich Fe-Al Intermetallics Using the Wire-Arc Additive Manufacturing Process, Addit. Manuf., 2015, 7, p 20–26. https://doi.org/10.1016/j.addma.2015.06.001CrossRef

14.

S.W. Williams, F. Martina, A.C. Addison, J. Ding, G. Pardal, and P. Colegrove, Wire+Arc Additive Manufacturing, Mater. Sci. Technol., 2016, 32, p 641–647. https://doi.org/10.1179/1743284715Y.0000000073CrossRef

15.

Y.F. Wang, X.Z. Chen, and C.C. Su, Microstructure and Mechanical Properties of Inconel 625 Fabricated by Wire-Arc Additive Manufacturing, Surf. Coat. Technol., 2019, 374, p 116123. https://doi.org/10.1016/j.surfcoat.2019.05.079CrossRef

16.

A. Horgar, H. Fostervoll, B. Nyhus, X. Ren, M. Eriksson, and O.M. Akselsen, Additive Manufacturing Using WAAM with AA5183 Wire, J. Mater. Process. Technol., 2018, 259, p 6874. https://doi.org/10.1016/j.jmatprotec.2018.04.014CrossRef

17.

J.R. Zhang, X.J. Di, C.N. Li, X.P. Zhao, L.Z. Ba, and X. Jiang, Additive Manufacturing of Inconel625-HSLA Steel Functionally Graded Material by Wire Arc Additive Manufacturing, Metall. Res. Technol., 2021 https://doi.org/10.1051/metal/2021063CrossRef

18.

X. Xiangfang, J. Ding, G. Supriyo, and S. Williams, Investigation of Process Factors Affecting Mechanical Properties of INCONEL 718 Superalloy in Wire + Arc Additive Manufacture Process, J. Mater. Process. Technol, 2019 https://doi.org/10.1016/j.jmatprotec.2018.10.023CrossRef

19.

D.R. Corradi, A.Q. Bracarense, Wu. Bintao, D. Cuiuri, Z. Pan, and H. Li, Effect of Magnetic Arc Oscillation on the Geometry of Single-Pass Multi-layer Walls and the Process Stability in Wire and Arc Additive Manufacturing, J. Mater. Process. Technol, 2020 https://doi.org/10.1016/j.jmatprotec.2020.116723CrossRef

20.

L. Wang, Wu. Chuansong, Ji. Chen, and J. Gao, Influence of the External Magnetic Field on Fluid Flow, Temperature Profile and Humping Bead in High Speed Gas Metal Arc Welding, Int. J. Heat Mass. Trans., 2018 https://doi.org/10.1016/j.ijheatmasstransfer.2017.09.130CrossRef

21.

C. Li, X. Zhang and J. Wang, The Effect of Axial External Magnetic Field on Tungsten Inert Gas Welding of Magnesium Alloy, Mater. Res. Exp., 2018 https://doi.org/10.1088/2053-1591/aabb39CrossRef

22.

R. Chen, Effect of External Magnetic Field on the Microstructure and Strength of Laser-Welded Aluminum to Titanium, J. Mater. Sci., 2020 https://doi.org/10.1007/s10853-019-04249-2CrossRef

23.

Q. Yao, Z. Luo, Y. Li, F.Y. Yan, and R. Duan, Effect of Electromagnetic Stirring on the Microstructures and Mechanical Properties of Magnesium Alloy Resistance Spot Weld, Mater. Des., 2014, 63, p 200–207. https://doi.org/10.1016/j.matdes.2014.06.004CrossRef

24.

A. Reichardt, R.P. Dillon, J.P. Borgonia, A.A. Shapiro, B.W. McEnerney, T. Momose, and P. Hosemann, Development and Characterization of Ti-6Al-4V to 304L Stainless Steel Gradient Components Fabricated with Laser Deposition Additive Manufacturing, Mater. Des, 2016 https://doi.org/10.1016/j.matdes.2016.05.016CrossRef

25.

W. Kurz and D.J. Fisher, Fundamentals of Solidification, Lausanne, Switzerland, 1986.

26.

J.F. Wang, Q.J. Sun, H. Wang, J.P. Liu, and J.C. Feng, Effect of Location on Microstructure and Mechanical Properties of Additive Layer Manufactured Inconel 625 Using Gas Tungsten Arc Welding, Mater. Sci. Eng. A, 2016 https://doi.org/10.1016/j.msea.2016.09.015CrossRef

27.

E.P. Cardozo, S. Rios, S. Ganguly, C.M. Ana Sofia, and D’Oliveira., Assessment of the Effect of Different Forms of Inconel 625 Alloy Feedstock in Plasma Transferred Arc (PTA) Additive Manufacturing, Int. J. Adv. Manuf. Tech, 2018 https://doi.org/10.1007/s00170-018-2340-zCrossRef

28.

J. Nguejio, F. Szmytka, S. Hallasi, A. Tanguy, S. Nardone, and M.G. Martinez, Comparison of Microstructure Features and Mechanical Properties for Additive Manufactured and Wrought Nickel Alloys 625, Mater. Sci. Eng. A., 2019, 764, p 138214. https://doi.org/10.1016/j.msea.2019.138214CrossRef

29.

D. Kong, C. Dong, X. Ni, L. Zhang, C. Man, J. Yao, Y. Ji, Y. Ying, K. Xiao, X. Cheng, and X. Li, High-Throughput Fabrication of Nickel-Based Alloys with Different Nb Contents Via a Dual-Feed Additive Manufacturing System: Effect of Nb Content on Microstructural and Mechanical Properties, J. Alloys Comp., 2019, 785(826), p 837. https://doi.org/10.1016/j.jallcom.2019.01.263CrossRef

30.

X. Ni, L. Zhang, Wu. Wenheng, and D. Zhu, Functionally Nb Graded inconel 718 Alloys Fabricated by Laser Melting Deposition: Mechanical Properties and Corrosion Behavior, Anti-Corros. Method. M., 2020, 67(1), p 16–23. https://doi.org/10.1108/ACMM-06-2019-2131CrossRef

31.

Y. Li, Z. Luo, F.Y. Yan, R. Duan, and Q. Yao, Effect of External Magnetic Field on Resistance Spot Welds of Aluminum Alloy, Mater. Des., 2014, 56, p 1025–1033. https://doi.org/10.1016/j.matdes.2013.12.005CrossRef

32.

J.D. Hunt, Steady State Columnar Equiaxed Growth of Dendrites and Eutectic, Mater. Sci. Eng., 1984, 65, p 75–83.CrossRef

33.

N. Thieme, M. Keil, D. Meier, P. Bonisch, K. Dadzis, O. Patzold, M. Stelter, L. Buttner, and J. Czarske, Directional Solidification of Gallium Under Time-Dependent Magnetic Fields with In Situ Measurements of the Melt Flow and the Solid-Liquid Interface, J. Cryst. Growth., 2019, 522, p 221–229. https://doi.org/10.1016/j.jcrysgro.2019.06.034CrossRef

34.

F. Matsuda, A.H. Nakagam, and K. Nakata, Effect of Electromagnetic Stirring on Weld Solidification Structure of Aluminum Alloy, Trans. Jpn. Weld Soc., 1998, 7, p 111–126.

35.

L.Y. Xu, M. Li, H. Jing, and Y.D. Han, Electrochemical Behavior of Corrosion Resistance of X65/Inconel 625 Welded Joints, Int. J. Electrochem. Sc., 2013, 8, p 2069–2079.

36.

L.Y. Xu, H.Y. Jing, and Y.D. Han, Effect of Welding on the Corrosion Behavior of X65/Inconel 625 in Simulated Solution, Weld World., 2018, 62, p 1–13. https://doi.org/10.1007/s40194-018-0549-yCrossRef

37.

S.E. Ziemniak and M.A. Goyette, Nickel(II) Oxide Solubility and Phase Stability in High Temperature Aqueous Solutions, J. Solut. Chem., 2004, 33(9), p 1135–1159. https://doi.org/10.1023/B:JOSL.0000048061.87789.81CrossRef

38.

X. Zhong, E.-H. Han, and Wu. Xinqiang, Corrosion Behavior of Alloy 690 in Aerated Supercritical Water, Corros. Sci., 2013, 66, p 369–379. https://doi.org/10.1016/j.corsci.2012.10.001CrossRef

39.

X.J. Wang, B.S. Wang, L.L. Zhang, C. Yang, and Y. Yang, Effect of Different Welding Processes on Electrochemical and Corrosion Behavior of Pure Nickel in 1 M NaCl Solution, Metals, 2017 https://doi.org/10.3390/met7120532CrossRef

40.

P. Marcus, V. Maurice, and H.H. Strehblow, Localized Corrosion (pitting): A Model of Passivity Breakdown Including the Role of the Oxide Layer Nanostructure, Corros. Sci., 2008, 50, p 2698–2704. https://doi.org/10.1016/j.corsci.2008.06.047CrossRef

41.

K. Łyczkowska and J. Michalska, Studies on the Corrosion Resistance of Laser-Welded Inconel 600 and Inconel 625 Nickel-Based Superalloys, Arch. Metall. Mater., 2017, 62(2), p 653–656. https://doi.org/10.1515/amm-2017-0100CrossRef

42.

L.Y. Xu, M. Li, H.Y. Jing, and Y.D. Han, Electrochemical Behavior of Corrosion Resistance of X65/Inconel 625 Welded Joints, Int. J. Electrochem. Sci., 2013, 8(2), p 2069–2079.

43.

N. Anbarasan, S. Jerome, and N. Arivazhagan, Argon and Argon-Hydrogen Shielding Gas Effects on the Laves Phase Formation and Corrosion Behavior of Inconel 718 gas Tungsten Arc Welds, J. Mater. Process. Technol., 2019, 263, p 374–384. https://doi.org/10.1016/j.jmatprotec.2018.07.038CrossRef

Titel: Effect of Electromagnetic Stirring Frequency on Inconel625-High Strength Low Alloy Steel Functionally Graded Material Fabricated by Wire Arc Additive Manufacturing
verfasst von: Jiarong Zhang
Xinjie Di
Chengning Li
Lingzhi Ba
Xing Jiang
Publikationsdatum: 23.05.2022
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 12/2022
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-022-07008-8

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 12/2022

Hydrothermal Sealing of Plasma Electrolytic Oxidation Coatings Developed on AZ31 Alloy

Oxidation Behavior of SiCf/SiC Minicomposites with Multilayered (BN/SiC)n Interfacial Coatings under Humid Environment

Effect of Shot Peening on the Ballistic Performance of Friction Stir Welded Magnesium Alloy (AZ31B) Joints

Hot Workability and Microstructural Evolution of Powder Metallurgy Ti-22Al-24Nb-0.5Mo Alloy during Hot Compression

Characterization of Residual Stresses in Conventional Forming and Hydroforming of Tailor Welded Blanks

Effect of Hard Cyclic Viscoplastic Deformation on the Microstructure, Mechanical Properties, and Electrical Conductivity of Cu-Cr Alloy

Premium Partner

Marktübersichten