nach oben

Tribology Letters

Erschienen in:

01.06.2022 | Original Paper

Effect of Ti₃SiC₂ Amount on Microstructures and Properties of TiAl Matrix Composites

verfasst von: Qin Zou, Zhichao Lou, Yong Guan, Yanguo Li, Jiangbo Xu, Yuanyuan Li, Lingyu Bu, Peng Wang, Yong’an Luo

Erschienen in: Tribology Letters | Ausgabe 2/2022

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The TiAl matrix composites were manufactured using spark plasma sintering under the conditions of 1100 °C/10 min/30 MPa. The effect of Ti₃SiC₂ amount on microstructures and properties of TiAl matrix composites was investigated. Ti₃SiC₂ was homogeneously distributed in the TiAl matrix, and it partly decomposed to form Ti₅Si₃ and TiC. The TiAl matrix with 30 wt% of Ti₃SiC₂ exhibited the lowest friction coefficient and wear rate of 0.507 and 1.35 × 10^–4 mm³ N⁻¹ m⁻¹ at room temperature and 0.423 and 0.21 × 10^–4 mm³ N⁻¹ m⁻¹ at 550 °C, while the compression strength reached the maximum value of 1080 GPa at room temperature and 640 GPa at 550 °C, respectively. The hardness reached the value of 5.1 GPa. The TiAl matrix composites had a lower friction coefficient and wear rate at 550 °C than at room temperature. A Ti₃SiC₂ lubricating film was formed on the friction surface of the TiAl matrix composites after friction test at room temperature, while a Fe–Ti–Al–Si-oxide lubricating film was formed after friction test at 550 °C. The wear mechanisms of the TiAl matrix composites with the Ti₃SiC₂ addition were mainly abrasive wear and adhesive wear at room temperature and 550 °C, respectively.

Vorheriger Artikel Air, Helium and Water Leakage in Rubber O-ring Seals with Application to Syringes

Nächster Artikel Transient Evolution of Rheological Properties of Dense Granular Inertial Flow Under Plane Shear

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Bewlay, B.P., Nag, S., Suzuki, A., Weimer, M.J.: TiAl alloys in commercial aircraft engines. Mater. High Temp. 33, 549–559 (2016). https://doi.org/10.1080/09603409.2016.1183068CrossRef

Cui, S., Cui, C.X., Xie, J.Q., Liu, S.J., Shi, J.J.: Carbon fibers coated with graphene reinforced TiAl alloy composite with high strength and toughness. Sci. Rep. 8, 2364 (2018). https://doi.org/10.1038/s41598-018-20799-yCrossRef

Pan, Y., Lu, X., Hayat, M., Yang, F., Liu, C.C., Li, Y., Li, X.Y., Xu, W., Qu, X.H., Cao, P.: Effect of Sn addition on the high-temperature oxidation behavior of high Nb-containing TiAl alloys. Corros. Sci. 116, 108449 (2020). https://doi.org/10.1016/j.corsci.2020.108449CrossRef

Tian, S.G., Lv, X.X., Yu, H.C., Wang, Q., Jiao, Z.H., Sun, H.F.: Creep behavior and deformation feature of TiAl-Nb alloy with various states at high temperature. Mater. Sci. Eng. A 651, 490–498 (2015). https://doi.org/10.1016/j.msea.2015.10.096CrossRef

Klocke, F., Herrig, T., Zeis, M., Klink, A.: Experimental research on the electrochemical machinability of selected γ-TiAl alloys for the manufacture of future aero engine components. Procedia CIRP 35, 50–54 (2015). https://doi.org/10.1016/j.procir.2015.08.050CrossRef

Jung, J.Y., Park, C., Bae, C.: Effects of high-response TiAl turbine wheel on engine performance under transient conditions. JSAE 2015, 01 (1881). https://doi.org/10.4271/2015-01-1881CrossRef

Cheng, J., Li, F., Zhu, S.Y., Yu, Y., Qiao, Z.H., Yang, J.: Electrochemical corrosion and tribological evaluation of TiAl alloy for marine application. Tribol. Int. 115, 483–492 (2017). https://doi.org/10.1016/j.triboint.2017.06.027CrossRef

Korotitskiy, A.V., Asnis, E.A., Piskun, N.V., Statkevich, I.I., Gorshenkov, M.V., Korotitski, A.V.: A promising microstructure/deformability adjustment of β-stabilized γ-TiAl intermetallics. Mater. Lett. 162, 180–184 (2016). https://doi.org/10.1016/j.matlet.2015.09.139CrossRef

Yeh, C.L., Sun, W.E.: Use of TiH₂ as a reactant in combustion synthesis of porous Ti₅Si₃ and Ti₅Si₃/TiAl intermetallics. J. Alloy. Compd. 669, 66–71 (2016). https://doi.org/10.1016/j.jallcom.2016.01.236CrossRef

10.

Tian, S.W., Jiang, H.T., Guo, W.Q., Zhang, G.H., Zeng, S.W.: Hot deformation and dynamic recrystallization behavior of TiAl-based alloy. Intermetallics 112, 106521 (2019). https://doi.org/10.1016/j.intermet.2019.106521CrossRef

11.

Sun, Y.J., Lin, Y.F., Zhang, N., Zhang, D.L.: Microstructures and mechanical properties of TiAl alloy fabricated by spark plasma sintering. Int. J. Mod. Phys. B 34, 2040036 (2020). https://doi.org/10.1142/S0217979220400366CrossRef

12.

Xu, Z.S., Shi, X.L., Zhang, Q.X., Zhai, W.Z., Yao, J., Chen, L., Zhu, Q.S., Xiao, Y.C.: High-temperature tribological performance of Ti₃SiC₂/TiAl self-lubricating composite against Si₃N₄ in air. J. Mater. Eng. Perform. 23, 2255–2264 (2014). https://doi.org/10.1007/s11665-014-0969-9CrossRef

13.

Xu, Z.S., Xue, B., Shi, X.L., Zhang, Q.X., Zhai, W.Z., Yao, J., Wang, Y.F.: sliding speed and load dependence of tribological properties of Ti₃SiC₂/TiAl composite. Tribol. Trans. 58, 87–96 (2014). https://doi.org/10.1080/10402004.2014.951748CrossRef

14.

Shen, Q., Shi, X.L., Zou, J.L., Yang, K., Huang, C., Zhang, A., Ibrahim, M.M., Wang, Y.F.: Tribological performance and self-lubricating film formation mechanism of TiAl-based composites at elevated temperatures. J. Mater. Eng. Perform. 26, 268–276 (2017). https://doi.org/10.1007/s11665-016-2433-5CrossRef

15.

Xu, Z.S., Shi, X.L., Wang, M., Zhai, W.Z., Yao, J., Song, S.Y., Zhang, Q.X.: Effect of Ag and Ti₃SiC₂ on tribological properties of TiAl matrix self-lubricating composites at room and increased temperatures. Tribol. Lett. 53, 617–629 (2014). https://doi.org/10.1007/s11249-014-0299-yCrossRef

16.

Xu, Z.S., Zhang, Q.X., Shi, X.L., Zhai, W.Z., Yang, K.: Tribological properties of TiAl matrix self-lubricating composites containing multilayer graphene and Ti₃SiC₂ at high temperatures. Tribol. Trans. 58(6), 1131–1141 (2015). https://doi.org/10.1080/10402004.2015.1046007CrossRef

17.

Xu, Z.S., Shi, X.L., Zhang, Q.X., Zhai, W.Z., Li, X.X., Yao, J., Chen, L., Zhu, Q.S., Xiao, Y.C.: Effect of sliding speed and applied load on dry sliding tribological performance of TiAl matrix self-lubricating composites. Tribol. Lett. 55(3), 393–404 (2014). https://doi.org/10.1007/s11249-014-0367-3CrossRef

18.

Ghosh, N., Harimkar, S.: Microstructure and wear behavior of spark plasma sintered Ti₃SiC₂ and Ti₃SiC₂–TiC composites. Ceram. Int. 39, 4597–4607 (2013). https://doi.org/10.4028/www.scientific.net/AMR.105-106.31CrossRef

19.

Rahmani, K., Majzoobi, G.: The effect of particle size on microstructure, relative density and indentation load of Mg-B4C composites fabricated at different loading rates. J. Compos. Mater. 54(17), 1–15 (2020). https://doi.org/10.1177/0021998319896009CrossRef

20.

Gürbüz, M., Mutuk, T., Uyan, P.: Mechanical, wear and thermal behaviors of graphene reinforced titanium composites. Met. Mater. Int. 27, 744–752 (2021). https://doi.org/10.1007/s12540-020-00673-1CrossRef

21.

Zhang, Z.F., Sun, Z.M., Hashimoto, H.: Rapid synthesis of ternary carbide Ti₃SiC₂ through pulse-discharge sintering technique from Ti/Si/TiC powders. Metall. Mater. Trans. A. 33, 3321–3328 (2002). https://doi.org/10.1007/s11661-002-0320-1CrossRef

22.

Talero, R., Trusilewicz, L., Delgado, A., Pedrajas, C., Lannegrand, R., Rahhal, V., Mejía, R., Delvastoe, S., Ramírezf, F.A.: Comparative and semi-quantitative XRD analysis of Friedel’s salt originating from pozzolan and Portland cement. Constr. Build. Mater. 25, 2370–2380 (2011). https://doi.org/10.1016/j.conbuildmat.2010.11.037CrossRef

23.

El-Raghy, T., Barsoum, M.W., Sika, M.: Reaction of Al with Ti₃SiC₂ in the 800–1000 °C temperature range. Mater. Sci. Eng., A 298, 174–178 (2001). https://doi.org/10.1016/S0921-5093(00)01281-8CrossRef

24.

Gu, W.L., Yan, C.K., Zhou, Y.C.: Reactions between Al and Ti₃SiC₂ in temperature range of 600–650 °C. Scripta Mater. 49, 1075–1080 (2003). https://doi.org/10.1016/j.scriptamat.2003.08.016CrossRef

25.

Wang, Q., Chen, G.Q., Wang, K., Fu, X.S., Zhou, W.L.: Microstructural evolution and growth kinetics of interfacial compounds in TiAl/Ti₃SiC₂ diffusion bonding joints. Mater. Sci. Eng., A 756, 149–155 (2019). https://doi.org/10.1016/j.msea.2019.04.034CrossRef

26.

Dang, W.T., Ren, S.F., Zhou, J.S., Yu, Y.J., Wang, L.Q.: The tribological properties of Ti₃SiC₂/Cu/Al/SiC composite at elevated temperatures. Tribol. Int. 104, 294–302 (2016). https://doi.org/10.1016/j.triboint.2016.09.008CrossRef

27.

Zuo, L.J., Ye, B., Feng, J., Zhang, H.X., Kong, X.Y., Jiang, H.Y.: Effect of ε-Al₃Ni phase on mechanical properties of Al–Si–Cu–Mg–Ni alloys at elevated temperature. Mater. Sci. Eng., A 772, 138794 (2020). https://doi.org/10.1016/j.msea.2019.138794CrossRef

28.

Shi, X.L., Yao, J., Xu, Z.S., Zhai, W.Z., Song, S.Y., Wang, M., Zhang, Q.X.: Tribological performance of TiAl matrix self-lubricating composites containing Ag, Ti₃SiC₂ and BaF₂/CaF₂ tested from room temperature to 600 °C. Mater. Des. 53, 620–633 (2014). https://doi.org/10.1016/j.matdes.2013.07.053CrossRef

29.

Xu, Z.S., Shi, X.L., Zhang, Q.X., Zhai, W.Z., Li, X.X., Yao, J., Song, S.Y.: Wear and friction of TiAl matrix self-lubricating composites against Si₃N₄ in air at room and elevated temperatures. Tribol. Trans. 57(6), 1017–1027 (2014). https://doi.org/10.1080/10402004.2014.931497CrossRef

30.

Zhai, W.Z., Shi, X.L., Wang, M., Xu, Z.S., Yao, J., Song, S.Y., Zhang, Q.X.: Friction and wear properties of TiAl-Ti₃SiC₂-MoS₂ composites prepared by spark plasma sintering. Tribol. Trans. 57(3), 416–424 (2014). https://doi.org/10.1080/10402004.2014.880539CrossRef

31.

Xu, Z.S., Yao, J., Shi, X.L., Zhai, W.Z., Ibrahim, A.M.M., Xiao, Y.C., Chen, L., Zhu, Q.S., Zhang, A.: A study of the frictional layer of TiAl-12Ag-5TiB₂ composite during dry sliding wear. J. Mater. Eng. Perform. 24(8), 2875–2884 (2015). https://doi.org/10.1007/s11665-015-1569-zCrossRef

32.

Barsoum, M.W.: The M_N+1AX_N phases: a new class of solids: thermodynamically stable nanolaminates. Prog. Solid State Chem. 28, 201–281 (2000). https://doi.org/10.1016/S0079-6786(00)00006-6CrossRef

33.

Gupta, S., Barsoum, M.W.: On the tribology of the MAX phases and their composites during dry sliding: a review. Wear 271, 1878–1894 (2011). https://doi.org/10.1016/j.wear.2011.01.043CrossRef

34.

Kalin, M.: Influence of flash temperatures on the tribological behaviour in low-speed sliding: a review. Mater. Sci. Eng. A 374, 390–397 (2004). https://doi.org/10.1016/j.msea.2004.03.031CrossRef

35.

Wang, L., Cheng, J., Zhu, S.Y., Yuan, Y., Qiaio, Z.H., Yang, J., Liu, W.M.: High temperature wear behaviors of TiAl-TiB₂ composites. Tribol. Lett. 65, 144 (2017). https://doi.org/10.1007/s11249-017-0924-7CrossRef

36.

An, Q., Huang, L.J., Bao, T., Zhang, R., Jiang, S., Gen, L., Xiao, M.M.: Microstructure and tribological behavior of in situ synthesized (TiB+TiC)/Ti6Al4V (TiB/TiC=1/1) composites. Tribol. Int. 121, 252–259 (2018). https://doi.org/10.1016/j.triboint.2020.106177CrossRef

37.

Yang, J., Gu, W., Pan, L.M., Song, K., Chen, X., Qiu, T.: Friction and wear properties of in situ (TiB₂ + TiC)/Ti₃SiC₂ composites. Wear 271, 2940–2946 (2011). https://doi.org/10.1016/j.wear.2011.06.017CrossRef

Titel: Effect of Ti3SiC2 Amount on Microstructures and Properties of TiAl Matrix Composites
verfasst von: Qin Zou
Zhichao Lou
Yong Guan
Yanguo Li
Jiangbo Xu
Yuanyuan Li
Lingyu Bu
Peng Wang
Yong’an Luo
Publikationsdatum: 01.06.2022
Verlag: Springer US
Erschienen in: Tribology Letters / Ausgabe 2/2022
Print ISSN: 1023-8883
Elektronische ISSN: 1573-2711
DOI: https://doi.org/10.1007/s11249-022-01571-w

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 2/2022

Adjusting for Running-in: Extension of the Archard Wear Equation

High Wear Resistance of Ultralow-Wear Polyethylene with Different Molecular Weights Under Different Contact Pressure

Review of Molecular Dynamics Simulations of Phosphonium Ionic Liquid Lubricants

Organic-Sulfonate Functionalized Graphene as a High Temperature Lubricant for Efficient Antifriction and Antiwear in Water Based Drilling Fluid

Simulating the Misting of Lubricant in the Piston Assembly of an Automotive Gasoline Engine: The Effect of Viscosity Modifiers and Other Key Lubricant Components

Influence of Natural Serpentine on Tribological Performance of Phosphate Bonded Solid Coatings

Premium Partner

Marktübersichten