nach oben

Journal of Materials Engineering and Performance

Erschienen in:

22.03.2022 | Technical Article

Microstructure, Fracture Behavior, and Mechanical and Frictional Properties of Ti(C_0.7N_0.3)-Based Cermets Containing Graphene

verfasst von: Lei Liang, Qiwen Zheng, Tianen Yang, Xianke Shi, Ji Xiong

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 9/2022

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Multilayer graphene as an extra carbon source was introduced into a Ti(C_0.7N_0.3)-based cermet, and the microstructure, fracture performance, and mechanical and frictional properties of the cermet were investigated in the current work. The results suggested that the number of undissolved Ti(C_0.7N_0.3) phases (dark cores) was reduced in the microstructure, while the (Ti, W, Mo) (C, N) solid solutions with more W and Mo but less Ti (bright cores) increased as the graphene content increased. Moreover, the ratio of the rim ((Ti, W, Mo) (C,N) solid solutions) thickness to the undissolved Ti(C_0.7N_0.3) core size gradually increased. Some high-carbon areas were found among (Ti, W, Mo) (C, N) solid solution rims when no less than 1.5 wt.% graphene was added, and it was finally confirmed that these high-carbon areas contained more graphene. When 0.75 wt.% graphene was added, the cermet with a moderate rim thickness and small dark cores had the highest flexure strength and hardness. The cermet containing excessive graphene had a high-volume fraction of high-carbon areas, and cracks propagated easily through these areas, leading to lower fracture toughness. The appropriate addition of graphene can reduce the friction coefficient and wear rate of Ti(C_0.7N_0.3)-based cermets at high temperatures.

Vorheriger Artikel Dissolution and Coarsening Kinetics of γ′ Precipitates in Waspaloy during Solution Treatment at Temperatures of 1000-1045 °C

Nächster Artikel Application of Hybrid Transient Thermal Tensioning/Trailing Active Cooling Treatment for Minimizing Distortion, Residual Stress, and Fatigue Crack Growth Rate of Friction Stir Welding Joints

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

C. Liu, N. Lin and Y.H. He, Influence of Mo₂C and TaC Additions on the Microstructure and Mechanical Properties of Ti(C, N)-Based Cermets, Ceram Int., 2016, 42(2), p 3569–3574. https://doi.org/10.1016/j.ceramint.2015.10.168CrossRef

S.M. Rafiaei, J. Kim and S. Kang, Effect of Nitrogen and Secondary Carbide on the Microstructure and Properties of (Ti_0.93W_0.07)C–Ni Cermets, Int. J. Refract. Metals Hard Mater., 2014, 44, p 123–128. https://doi.org/10.1016/j.ijrmhm.2014.02.001CrossRef

B. Zhan, N. Liu, Z. Jin, Q. Li and J. Shi, Effect of VC/Cr₃C₂ on Microstructure and Mechanical Properties of Ti(C, N)-Based Cermets, T Nonferr. Metal Soc., 2012, 22(5), p 1096–1105. https://doi.org/10.1016/S1003-6326(11)61289-2CrossRef

H. Yang, Z. Wang, X. Yue, P. Ji and S. Shu, Simultaneously Improved Strength and Toughness of In Situ bi-Phased TiB₂–Ti(C, N)–Ni Cermets by Mo Addition, J Alloy Compd., 2020, 820, 153068. https://doi.org/10.1016/j.jallcom.2019.153068CrossRef

Z. Cao, N. Jin, J. Ye, D. Zhuang and Y. Liu, The Effects of Nitrogen on the Stability, Elastic Properties and Electronic Structure of Ti(C_xN_1−x): A First Principles Investigation, Int. J. Refract Metal Hard Mater., 2021, 94, 105382. https://doi.org/10.1016/j.ijrmhm.2020.105382CrossRef

S. Tang, D. Liu, P. Li, L. Jiang and Q. Niu, Mechanical Properties and Cutting Performance of TiCN-Based Cermets Fabricated by Spark Plasma Sintering, Int. J. Mach. Mach. Mater., 2018, 20(1), p 90. https://doi.org/10.1504/IJMMM.2018.089475CrossRef

X. Kang, N. Lin, Y. He and M. Zhang, Influence of ZrC Addition on the Microstructure, Mechanical Properties and Oxidation Resistance of Ti(C, N)-Based Cermets, Ceram Int., 2018, 44(10), p 11151–11159. https://doi.org/10.1016/j.ceramint.2018.03.131CrossRef

W. Lengauer and F. Scagnetto, Ti(C, N)-Based Cermets: Critical Review of Achievements and Recent Developments, Solid State Phenom., 2018, 274, p 53–100. https://doi.org/10.4028/www.scientific.net/SSP.274.53CrossRef

N. Liu, X. Liu, X. Zhang and L. Zhu, Effect of Carbon Content on the Microstructure and Mechanical Properties of Superfine Ti(C, N)-Based Cermets, Mater Charact., 2008, 59(10), p 1440–1446. https://doi.org/10.1016/j.matchar.2008.01.006CrossRef

10.

E. Chicardi, Y. Torres, M.J. Sayagués, V. Medri, C. Melandri, J.M. Córdoba et al., Toughening of Complete Solid Solution Cermets by Graphite Addition, Chem Eng J., 2015, 267, p 297–305. https://doi.org/10.1016/j.cej.2015.01.022CrossRef

11.

J. Zackrisson and H.O. Andrén, Effect of Carbon Content on the Microstructure and Mechanical Properties of (Ti, W, Ta, Mo)(C, N)–(Co, Ni) Cermets, Int. J. Refract Metal Hard Mater., 1999, 17(4), p 265–273. https://doi.org/10.1016/S0263-4368(98)00074-2CrossRef

12.

Y. Li, N. Liu and Y. Li, Carbon Nanotube/Ultrafine Grade Ti(C, N) Based Cermets Composite, Mater Sci Tech-Lond., 2013, 27(8), p 1287–1293. https://doi.org/10.1179/026708309X12506933872829CrossRef

13.

S. Luyckx and A.D. Love, Empirical Quantitative Relationships Among Grain Size, Mean Free Path, Contiguity and Cobalt Content in WC-Co Hardmetal, Trans. R. Soc. South Afr., 2003, 58(2), p 145–148. https://doi.org/10.1080/00359190309520469CrossRef

14.

L. Makhele-Lekala, S. Luyckx and F.R.N. Nabarro, Semi-empirical Relationship Between the Hardness, Grain Size and Mean Free Path of WC–Co, Int. J. Refract Metal Hard Mater., 2001, 19(4–6), p 245–249. https://doi.org/10.1016/S0263-4368(01)00022-1CrossRef

15.

G. Liu, R. Li, T. Yuan, M. Zhang and F. Zeng, Spark Plasma Sintering of Pure TiCN: Densification Mechanism, Grain Growth and Mechanical Properties, Int. J. Refract Metal Hard Mater., 2017, 66, p 68–75. https://doi.org/10.1016/j.ijrmhm.2017.02.008CrossRef

16.

F. Bonaccorso, L. Colombo, G. Yu, M. Stoller, V. Tozzini, A.C. Ferrari et al., Graphene, Related Two-dimensional Crystals, and Hybrid Systems for Energy Conversion and Storage, Science, 2015, 347(6217), p 1246501. https://doi.org/10.1126/science.1246501CrossRef

17.

A.A. Balandin, S. Ghosh, W. Bao, I. Calizo, D. Teweldebrhan, F. Miao et al., Superior Thermal Conductivity of Single-Layer Graphene, Nano Lett., 2008, 8(3), p 902–907. https://doi.org/10.1021/nl0731872CrossRef

18.

V.K. Singh, Densification of Alumina and Silica in the Presence of a Liquid Phase, J. Am. Ceram. Soc., 1981, 64(10), p C-133-C–136. https://doi.org/10.1111/j.1151-2916.1981.tb10235.xCrossRef

19.

E. Bódis, I. Cora, C. Balázsi, P. Németh, Z. Károly, S. Klébert et al., Spark Plasma Sintering of graphene Reinforced Silicon Carbide Ceramics, Ceram Int., 2017, 43(12), p 9005–9011. https://doi.org/10.1016/j.ceramint.2017.04.042CrossRef

20.

M. Gaier, Z.N. Farhat and K.P. Plucknett, The Effects of Graphene Nano-platelet Additions on the Sliding Wear of TiC-Ni₃Al Cermets, Tribol Int., 2019, 130, p 119–132. https://doi.org/10.1016/j.triboint.2018.09.015CrossRef

21.

Z. Xu, X. Shi, W. Zhai, J. Yao, S. Song and Q. Zhang, Preparation and Tribological Properties of TiAl Matrix Composites Reinforced by Multilayer Graphene, Carbon, 2014, 67, p 168–177. https://doi.org/10.1016/j.carbon.2013.09.077CrossRef

22.

T.E. Yang, L. Ni, J. Xiong, R. Shi and Q. Zheng, Flank Wear Mechanism and Tool Endurance of (Ti, W)C-M_o2C-Co Cermets during Dry Turning, Ceram Int., 2018, 44(7), p 8447–8455. https://doi.org/10.1016/j.ceramint.2018.02.040CrossRef

23.

P. Lindahl, P. Gustafson, U. Rolander, L. Stals and H.O. Andrén, Microstructure of Model Cermets with High Mo or W Content, Int. J. Refract Metal Hard Mater., 1999, 17(6), p 411–421. https://doi.org/10.1016/S0263-4368(99)00032-3CrossRef

24.

Q. Zheng, W. Yao and L. Lim, Ostwald Ripening and Grain Growth in Ti(C, N)-Based Cermets during Liquid Phase Sintering, Int. J. Refract Metal Hard Mater., 2016, 58, p 1–7. https://doi.org/10.1016/j.ijrmhm.2016.03.008CrossRef

25.

H. Xiong, Y. Wen, X. Gan, Z. Li and L. Chai, Influence of Coarse TiCN Content on the Morphology and Mechanical Properties of Ultrafine TiCN-Based Cermets, Mater. Sci. Eng., A, 2017, 682, p 648–655. https://doi.org/10.1016/j.msea.2016.11.085CrossRef

26.

Y. Zheng, W. Liu, S. Wang and W. Xiong, Effect of Carbon Content on the Microstructure and Mechanical Properties of Ti(C, N)-Based Cermets, Ceram Int., 2004, 30(8), p 2111–2115. https://doi.org/10.1016/j.ceramint.2003.11.016CrossRef

27.

W. Zhang, Y. Peng, P. Zhou, W. Chen, Y. Du, W. Xie et al., Experimental Investigation and Computer Simulation of Gradient Zone Formation in WC-Ti(C, N)-TaC-NbC-Co Cemented Carbides, J Phase Equilib Diff., 2013 https://doi.org/10.1007/s11669-013-0225-2CrossRef

28.

J. Zackrisson, H.O. Andrén and U. Rolander, Development of Cermet Microstructures during Sintering, Metall. and Mater. Trans. A., 2001, 32(1), p 85–94. https://doi.org/10.1007/s11661-001-0104-zCrossRef

29.

E. Conforto, D. Mari and T. Cutard, The Role of Molybdenum in the Hard-Phase Grains of (Ti, Mo)(C, N)–Co Cermets, Philos Mag., 2004, 84(17), p 1717–1733. https://doi.org/10.1080/14786430310001659516CrossRef

30.

Q. Yang, W. Xiong, G. Zhang and B. Huang, Grain Growth in Ti(C, N)-Based Cermets During Liquid-Phase Sintering, J Am Ceram Soc., 2015, 98(3), p 1005–1012. https://doi.org/10.1111/jace.13359CrossRef

31.

Y. Li, N. Liu, X. Zhang and C. Rong, Effect of Mo Addition on the Microstructure and Mechanical Properties of Ultra-fine Grade TiC–TiN–WC–Mo₂C–Co Cermets, Int. J. Refract Metal Hard Mater., 2008, 26(3), p 190–196. https://doi.org/10.1016/j.ijrmhm.2007.05.005CrossRef

32.

G. Östberg, K. Buss, M. Christensen, S. Norgren, H. Andrén, D. Mari et al., Mechanisms of Plastic Deformation of WC–Co and Ti(C, N)–WC–Co, Int. J. Refract Metal Hard Mater., 2006, 24(1–2), p 135–144. https://doi.org/10.1016/j.ijrmhm.2005.04.009CrossRef

33.

J. Sun, J. Zhao, F. Gong, Z. Li and X. Ni, Design, Fabrication and Characterization of Multi-layer Graphene Reinforced Nanostructured Functionally Graded Cemented Carbides, J Alloy Compd., 2018, 750, p 972–979. https://doi.org/10.1016/j.jallcom.2018.04.108CrossRef

34.

A.V. Shatov, S.S. Ponomarev and S.A. Firstov, Fracture of WC–Ni Cemented Carbides with Different Shape of WC Crystals, Int. J. Refract Metal Hard Mater., 2008, 26(2), p 68–76. https://doi.org/10.1016/j.ijrmhm.2007.03.002CrossRef

35.

X. Zeng, J. Teng, J. Yu, A. Tan, D. Fu and H. Zhang, Fabrication of Homogeneously Dispersed Graphene/Al Composites by Solution Mixing and Powder Metallurgy, Int. J. Miner. Metall. Mater., 2018, 25(1), p 102–109. https://doi.org/10.1007/s12613-018-1552-4CrossRef

36.

J. Luo and R. Stevens, Porosity-Dependence of Elastic Moduli and Hardness of 3Y-TZP Ceramics, Ceram Int., 1999, 25(3), p 281–286. https://doi.org/10.1016/S0272-8842(98)00037-6CrossRef

37.

Y. Fang, X. Zhao, M. Zhang, G. Du, J. Wu, H. Cheng et al., Properties of Ti(C, N)-Based Cermets Reinforced with ZrO2 Whiskers Deposited via Sulfate Flux at High Temperatures, Vacuum, 2021, 191, 110336. https://doi.org/10.1016/j.vacuum.2021.110336CrossRef

38.

L. Sun, T.E. Yang, C. Jia and J. Xiong, Effects of Graphite on the Microstructure and Properties of Ultrafine WC-11Co Composites by Spark Plasma Sintering, Rare Met., 2011, 30(1), p 63–67. https://doi.org/10.1007/s12598-011-0198-4CrossRef

39.

J. Jung and S. Kang, Effect of Ultra-fine Powders on the Microstructure of Ti(CN)–xWC–Ni Cermets, Acta Mater., 2004, 52(6), p 1379–1386. https://doi.org/10.1016/j.actamat.2003.11.021CrossRef

40.

Mishra A. Reduction of Sliding Wear of Alloys by Using Oxides. Int. J. Mech. Eng. Robot. Res., 2014, 3(3), p 598–602. http://www.ijmerr.com/show-124-520-1.html

41.

J. Glascott, F.H. Stott and G.C. Wood, The Effectiveness of Oxides in Reducing Sliding Wear of Alloys, Oxid Met., 1985, 24(3–4), p 99–114. https://doi.org/10.1007/BF00664227CrossRef

42.

Y. Fang, Y. Zhang, J. Song, H. Fan and L. Hu, Influence of Structural Parameters on the Tribological Properties of Al₂O₃/Mo Laminated Nanocomposites, Wear, 2014, 320, p 152–160. https://doi.org/10.1016/j.wear.2014.09.003CrossRef

43.

K. Broniszewski, J. Wozniak, K. Czechowski, L. Jaworska and A. Olszyna, Al₂O₃–Mo Cutting Tools for Machining Hardened Stainless Steel, Wear, 2013, 303(1–2), p 87–91. https://doi.org/10.1016/j.wear.2013.03.002CrossRef

44.

Y.G. Zhou, X.T. Zu, F. Gao, H.Y. Xiao and H.F. Lv, Electronic and Magnetic Properties of Graphene Absorbed with S Atom: A First-Principles Study, J Appl Phys., 2009, 105(10), p 104311. https://doi.org/10.1063/1.3130401CrossRef

45.

C. Sun, Y. Huang, Q. Shen, W. Wang, W. Pan, P.A. Zong et al., Embedding Two-dimensional Graphene Array in Ceramic Matrix, Sci Adv., 2020 https://doi.org/10.1126/sciadv.abb1338CrossRef

46.

L. Zhou, J. Xiong, Z. Guo, J. Ye and J. Liu, Tribological Performances of Ti(C, N)-Based Cermets with Different Graphite Contents in Dry Sliding Condition, Int. J. Refract Metal Hard Mater., 2017, 68, p 113–120. https://doi.org/10.1016/j.ijrmhm.2017.07.001CrossRef

47.

Q. Gou, J. Xiong, Z. Guo, J. Liu, L. Yang and X. Li, Influence of NbC Additions on Microstructure and Wear Resistance of Ti(C, N)-Based Cermets Bonded by CoCrFeNi High-Entropy Alloy, Int. J. Refract Metal Hard Mater., 2021, 94, p 105375. https://doi.org/10.1016/j.ijrmhm.2020.105375CrossRef

Titel: Microstructure, Fracture Behavior, and Mechanical and Frictional Properties of Ti(C0.7N0.3)-Based Cermets Containing Graphene
verfasst von: Lei Liang
Qiwen Zheng
Tianen Yang
Xianke Shi
Ji Xiong
Publikationsdatum: 22.03.2022
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 9/2022
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-022-06786-5

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 9/2022

Correction to: Simultaneous Effects of Carbon Nanotube Content and Diameter Size on Microstructure and Mechanical Properties of Double Pressed Double Sintered Al/Carbon Nanotube Nanocomposites

Sliding Friction and Wear Properties of GCr15 Steel under Different Lubrication Conditions

Sustainable Hard Machining of AISI 304 Stainless Steel Through TiAlN, AlTiN, and TiAlSiN Coating and Multi-Criteria Decision Making Using Grey Fuzzy Coupled Taguchi Method

Editorial

Failure Analysis of Abnormal Bulging and Cracking for High-Pressure Steam Pipe

Analyses of Axisymmetric Drawing-Bulging Forming Process of Sheet Metal Using Parametric and Direct Integral Methods

Premium Partner

Marktübersichten